Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › VALVE CLEARANCE › 2013.08–2016.07
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091000 VALVE CLEARANCE N

1NZ-FE ENGINE MECHANICAL  VALVE CLEARANCE  ADJUSTMENT  


PROCEDURE

Hide 1. PRECAUTION

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51441C 3.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51451A 4.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 11212 6.REMOVE NO. 2 CYLINDER HEAD COVER

Hide 12261 8.DISCONNECT VENTILATION HOSE

Hide 23820 9.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 11201 10.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11.INSPECT VALVE CLEARANCE

HINT:

Inspect the valve clearance when the engine is cold.


a.

Set the No. 1 cylinder to TDC/compression.

i.
A116203C02
2.146,1.042 2.406,1.948 true 2.26,1.01 2.688,1.927 true 2.365,1.979 2.531,2.156 0.167,0.177 10 false *a 2.656,1.969 2.823,2.146 0.167,0.177 10 false *b
*a Timing Notch
*b Timing Mark "0"


Turn the crankshaft damper sub-assembly and align its timing notch with the timing mark "0" of the oil pump assembly.


ii.
A116204C01
1.094,0.719 1.156,1.75 1.156,1.75 2.063,1.521 false 2.167,1.094 1.156,1.74 false 0.969,1.729 1.146,1.906 0.177,0.177 10 false *a
*a Timing Mark


Check that both timing marks on the camshaft timing sprocket and camshaft timing gear assembly are facing upward, as shown in the illustration.

HINT:

If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.




b.
A116201

Check the valves indicated in the illustration.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Valve clearance (cold):
for intake:

0.15 to 0.25 mm (0.006 to 0.010 in.)

for exhaust:

0.25 to 0.35 mm (0.010 to 0.014 in.)



ii.

Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.



c.

Turn the crankshaft 1 complete revolution (360°) and align its timing notch with the timing mark "0" of the oil pump assembly.


d.
A116202

Check the valves indicated in the illustration.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Valve clearance (cold):
for intake:

0.15 to 0.25 mm (0.006 to 0.010 in.)

for exhaust:

0.25 to 0.35 mm (0.010 to 0.014 in.)



ii.

Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.



Hide 12.ADJUST VALVE CLEARANCE

a.

Remove the engine mounting insulator sub-assembly RH.

Click hereEngine / Hybrid System>1NZ-FE LUBRICATION>OIL PUMP>REMOVAL




d.

Remove the 16 valve lifters from the cylinder head sub-assembly.


e.
A111168

Using a micrometer, measure the thickness of the removed valve lifter.


f.

Calculate the thickness of a new valve lifter so that the valve clearance comes to within the specified values.

A Thickness of new valve lifter
B Thickness of used valve lifter
C Measured valve clearance

Valve clearance:

Intake A = B + (C - 0.20 mm (0.008 in.))

Exhaust A = B + (C - 0.30 mm (0.012 in.))



g.

Select a new valve lifter with a thickness as close to the calculated values as possible.

HINT:

Valve lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).


A105866C01
1.271,0.521 1.583,0.677 0.313,0.156 10 false *a 0.719,1.125 1.031,1.281 0.313,0.156 10 false *b
*a Measured clearance
mm (in.)
*b Installed valve lifter thickness
mm (in.)


Intake valve clearance (cold):

0.15 to 0.25 mm (0.006 to 0.010 in.)


EXAMPLE:

A 5.250 mm (0.2067 in.) valve lifter is installed, and measured clearance is 0.400 mm (0.0158 in.). Replace the 5.250 mm (0.2067 in.) valve lifter with a new No. 46 valve lifter.


New Valve Lifter Thickness:
Valve Lifter No. Thickness Valve Lifter No. Thickness Valve Lifter No. Thickness
06 5.060 (0.1992) 30 5.300 (0.2087) 54 5.540 (0.2181)
08 5.080 (0.2000) 32 5.320 (0.2094) 56 5.560 (0.2189)
10 5.100 (0.2008) 34 5.340 (0.2102) 58 5.580 (0.2197)
12 5.120 (0.2016) 36 5.360 (0.2110) 60 5.600 (0.2205)
14 5.140 (0.2024) 38 5.380 (0.2118) 62 5.620 (0.2213)
16 5.160 (0.2031) 40 5.400 (0.2126) 64 5.640 (0.2220)
18 5.180 (0.2039) 42 5.420 (0.2134) 66 5.660 (0.2228)
20 5.200 (0.2047) 44 5.440 (0.2142) 68 5.680 (0.2236)
22 5.220 (0.2055) 46 5.460 (0.2150) 70 5.700(0.2244)
24 5.240 (0.2063) 48 5.480 (0.2157) 72 5.720 (0.2252)
26 5.260 (0.2071) 50 5.500 (0.2165) 74 5.740 (0.2260)
28 5.280 (0.2079) 52 5.520 (0.2173) - -


A105867C01
0.958,0.469 1.271,0.625 0.313,0.156 10 false *a 0.375,0.979 0.688,1.135 0.313,0.156 10 false *b
*a Measured clearance
mm (in.)
*b Installed valve lifter thickness
mm (in.)


Exhaust valve clearance (Cold):

0.25 to 0.35 mm (0.010 to 0.014 in.)


EXAMPLE:

A 5.340 mm (0.2102 in.) valve lifter is installed, and measured clearance is 0.440 mm (0.0173 in.). Replace the 5.340 mm (0.2102 in.) valve lifter with a new No. 48 valve lifter.


New Valve Lifter Thickness:
Valve Lifter No. Thickness Valve Lifter No. Thickness Valve Lifter No. Thickness
06 5.060 (0.1992) 30 5.300 (0.2087) 54 5.540 (0.2181)
08 5.080 (0.2000) 32 5.320 (0.2094) 56 5.560 (0.2189)
10 5.100 (0.2008) 34 5.340 (0.2102) 58 5.580 (0.2197)
12 5.120 (0.2016) 36 5.360 (0.2110) 60 5.600 (0.2205)
14 5.140 (0.2024) 38 5.380 (0.2118) 62 5.620 (0.2213)
16 5.160 (0.2031) 40 5.400 (0.2126) 64 5.640 (0.2220)
18 5.180 (0.2039) 42 5.420 (0.2134) 66 5.660 (0.2228)
20 5.200 (0.2047) 44 5.440 (0.2142) 68 5.680 (0.2236)
22 5.220 (0.2055) 46 5.460 (0.2150) 70 5.700 (0.2244)
24 5.240 (0.2063) 48 5.480 (0.2157) 72 5.720 (0.2252)
26 5.260 (0.2071) 50 5.500 (0.2165) 74 5.740 (0.2260)
28 5.280 (0.2079) 52 5.520 (0.2173) - -



h.

Install the selected valve lifter to the cylinder head sub-assembly.




k.

Install the engine mounting insulator sub-assembly RH.

Click hereEngine / Hybrid System>1NZ-FE LUBRICATION>OIL PUMP>INSTALLATION


Hide 11201 13.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23820 14.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 12261 15.CONNECT VENTILATION HOSE

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 51441C 20.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51405A 21.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 22.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)