Home › Engine / Hybrid System › 2NZ-FE COOLING › RADIATOR › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017082 2NZ-FE COOLING _0092345 RADIATOR A

2NZ-FE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16561 1.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL (w/ No. 1 Radiator to Support Seal)

HINT:

This procedure is only performed when replacing the No. 1 radiator to support seal with a new one.


a.
A347852E01
2.271,0.073 3.354,0.281 1.083,0.208 10 false 63 mm (2.48 in.)

Install the No. 1 radiator to support seal for lower side to the radiator assembly.

HINT:

Make sure that the No. 1 radiator to support seal does not overlap onto the radiator core plate.



b.
A347853E01
2.25,1.938 3.365,2.146 1.115,0.208 10 false 63 mm (2.48 in.)

Install the No. 1 radiator to support seal for upper side to the radiator assembly.

HINT:

Make sure that the No. 1 radiator to support seal does not overlap onto the radiator core plate.



Hide 2.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install the radiator drain cock plug to the radiator assembly.

NOTICE:

Replace the O-ring if it is damaged.



Hide 16535 3.INSTALL LOWER RADIATOR SUPPORT

a.

Install the 2 lower radiator supports to the radiator assembly.


Hide 16523A 4.INSTALL RADIATOR SUPPORT CUSHION

a.

Install the 2 radiator support cushions to the radiator assembly.


Hide 16561 5.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL (w/ No. 1 Radiator to Support Seal)

HINT:

This procedure is only performed when replacing the No. 1 radiator to support seal with a new one.


a.
A350134E01
2.635,0.688 3.188,1.052 0.552,0.365 10 false 13 mm (0.51 in.) 1.135,0.156 2.219,0.375 1.083,0.219 10 false 10 mm (0.39 in.)

Install the No. 1 radiator to support seal to the fan shroud.


Hide 16711 6.INSTALL FAN SHROUD

A302956

a.

Engage the 2 guides and 2 claws to install the fan shroud to the radiator assembly.


Hide 16400 7.INSTALL RADIATOR ASSEMBLY (w/ Cooler System)

a.
A302965

Install the radiator assembly together with fan shroud to the vehicle.

NOTICE:

Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.



b.
A302957

Engage the 2 guides and 2 claws to install the cooler condenser assembly to the radiator assembly.

HINT:

While tilting the cooler condenser assembly toward the front of the vehicle, install the cooler condenser assembly to the radiator assembly.



c.

Engage the 3 clamps to connect the wire harness to the fan shroud.


d.

Connect the cooling fan motor connector.


Hide 16400 8.INSTALL RADIATOR ASSEMBLY (w/o Cooler System)

a.
A302965

Install the radiator assembly together with fan shroud to the vehicle.


b.

Engage the 3 clamps to connect the wire harness to the fan shroud.


c.

Connect the cooling fan motor connector.


Hide 32941 9.CONNECT INLET NO. 1 OIL COOLER HOSE (for Automatic Transaxle)

A310447C01
0.24,1.188 0.427,1.396 0.188,0.208 10 true A 0.26,2.073 0.573,2.271 0.313,0.198 10 false *a 0.979,2.052 1.292,2.25 0.313,0.198 10 false *b 1.49,2.333 1.802,2.531 0.313,0.198 10 false *c 1.313,2.99 1.646,3.188 0.333,0.198 10 false 180°
*a View A
*b Top of Vehicle
*c Right Side of Vehicle


a.

Connect the inlet No. 1 oil cooler hose to the radiator assembly with the hose clip.

NOTICE:

Perform the installation with the hose clip at the correct angle.



Hide 32942 10.CONNECT OUTLET NO. 1 OIL COOLER HOSE (for Automatic Transaxle)

a.
A310448C01
2.094,0.531 2.292,0.677 0.198,0.146 10 true A 0.958,2.115 1.271,2.313 0.313,0.198 10 false *a 1.677,2.104 1.99,2.302 0.313,0.198 10 false *b 2.188,2.385 2.5,2.583 0.313,0.198 10 false *c 2.01,3.073 2.625,3.271 0.615,0.198 10 false 180°
*a View A
*b Top of Vehicle
*c Right Side of Vehicle


Connect the outlet No. 1 oil cooler hose to the radiator assembly with the hose clip.

NOTICE:

Perform the installation with the hose clip at the correct angle.



Hide 16572D 11.CONNECT NO. 2 RADIATOR HOSE

a.
A302896C02
2.052,2.948 2.333,3 true 1.167,0.781 1.323,0.979 0.156,0.198 10 true A 1.385,2.031 1.698,2.229 0.313,0.198 10 false *a 2.385,2.917 2.698,3.115 0.313,0.198 10 false *b 2.083,2.083 2.396,2.281 0.313,0.198 10 false *c 1.479,2.646 1.792,2.844 0.313,0.198 10 false *d
*a View A
*b Hose Paint Mark
*c Top of Vehicle
*d Left Side of Vehicle


Connect the No. 2 radiator hose to the radiator assembly with the hose clip.

NOTICE:

Perform the installation with the No. 2 radiator hose and hose clip at the correct angle.



Hide 16573B 12.CONNECT NO. 3 RADIATOR HOSE

a.
A302895C02
0.75,3.135 0.823,2.813 true 0.51,2.208 0.823,2.365 0.313,0.156 10 false *a 0.594,3.115 0.906,3.271 0.313,0.156 10 false *b 1.219,2.208 1.531,2.365 0.313,0.156 10 false *c 0.542,2.573 0.854,2.729 0.313,0.156 10 false *d 2.177,1.198 2.333,1.396 0.156,0.198 10 true A
*a View A
*b Hose Paint Mark
*c Top of Vehicle
*d Left Side of Vehicle


Connect the No. 3 radiator hose to the radiator assembly with the hose clip.

NOTICE:

Perform the installation with the No. 3 radiator hose and hose clip at the correct angle.



Hide 13.CONNECT RADIATOR RESERVOIR TANK HOSE

a.

Connect the radiator reservoir tank hose to the water filler sub-assembly.


Hide 16750 14.INSTALL FAN SHROUD VENTILATION DUCT ASSEMBLY (w/ Fan Shroud Ventilation Duct)

a.

Engage the 2 guides and 2 claws to install the fan shroud ventilation duct assembly to the radiator assembly.


Hide 53216A 15.INSTALL UPPER RADIATOR SUPPORT (for LHD)

a.

Install the upper radiator support to the radiator support assembly with the 4 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Connect the low pitched horn assembly connector.


c.

Engage the 2 clamps to connect the wire harness to the upper radiator support.


d.

Engage the clamp to connect the hood lock control cable assembly to the upper radiator support.


Hide 53216A 16.INSTALL UPPER RADIATOR SUPPORT (for RHD)

a.

Install the upper radiator support to the radiator support assembly with the 4 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Connect the low pitched horn assembly connector.


c.

Engage the 2 clamps to connect the wire harness to the upper radiator support.


d.

Engage the clamp to connect the hood lock control cable assembly to the upper radiator support.


Hide 88891H 17.INSTALL NO. 1 COOLER COVER (w/o Fan Shroud Ventilation Duct)

Hide 53215B 18.INSTALL HOOD LOCK SUPPORT (for Sedan)

a.

Install the hood lock support to the radiator support assembly with the 2 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Engage the clamp to connect the wire harness to the hood lock support.


Hide 53215B 19.INSTALL HOOD LOCK SUPPORT (for Hatchback)

a.

Install the hood lock support to the radiator support assembly with the 2 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Connect the hood lock support to the front bumper assembly with the clip.


c.

Engage the clamp to connect the wire harness to the hood lock support.


Hide 53510 20.INSTALL HOOD LOCK ASSEMBLY (for Sedan LHD)

Hide 53510 21.INSTALL HOOD LOCK ASSEMBLY (for Sedan RHD)

Hide 53510 22.INSTALL HOOD LOCK ASSEMBLY (for Hatchback LHD)

Hide 53510 23.INSTALL HOOD LOCK ASSEMBLY (for Hatchback RHD)

Hide 89173 24.INSTALL FRONT AIRBAG SENSOR (w/ Airbag System)

Hide 53101 25.INSTALL RADIATOR GRILLE SUB-ASSEMBLY (for Hatchback)

Hide 53141F 26.INSTALL RADIATOR COVER (for Hatchback)

Hide 81150 27.INSTALL HEADLIGHT ASSEMBLY LH (for Sedan)

Hide 81150 28.INSTALL HEADLIGHT ASSEMBLY RH (for Sedan)

HINT:

Use the same procedure as for the LH side.