Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › ENGINE ASSEMBLY(for Automatic Transaxle) › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017074 2NZ-FE ENGINE MECHANICAL _0091017 ENGINE ASSEMBLY(for Automatic Transaxle) A

2NZ-FE ENGINE MECHANICAL  ENGINE ASSEMBLY(for Automatic Transaxle)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Fan Shroud Ventilation Duct)

Hide 3.DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.REMOVE FRONT WHEELS

Hide 51442C 5.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

a.

Remove the 3 bolts, 5 screws and engine under cover LH from the vehicle.


Hide 51441C 6.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

a.

Remove the 2 bolts, 2 screws and engine under cover RH from the vehicle.


Hide 51451A 7.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

a.

Remove the 4 screws, 5 clips and center engine under cover from the vehicle.


Hide 51405A 8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

a.

Remove the 11 bolts and No. 1 engine under cover sub-assembly from the vehicle.


Hide 11.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 11212 12.REMOVE NO. 2 CYLINDER HEAD COVER

Hide 23820 13.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 23827A 14.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE

Hide 17341T 15.DISCONNECT NO. 1 AIR HOSE

Hide 17735 16.REMOVE AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

Hide 17801 17.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.
A310643

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


Hide 18.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A111178

Disengage the clamp to disconnect the engine wire from the air cleaner case sub-assembly.


b.

Remove the 3 bolts and air cleaner case sub-assembly from the air cleaner bracket.


Hide 23820 19.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY

A106614

a.

Loosen the 2 hose clips and remove the fuel vapor feed hose assembly from the cylinder head cover sub-assembly and fuel tube.


Hide 28800 20.REMOVE BATTERY

a.

Remove the terminal cover from the positive (+) battery terminal.


b.
A111179C01
0.406,0.198 0.573,0.333 true 0.854,0.24 0.729,0.5 true 0.229,0.094 0.542,0.25 0.313,0.156 10 false *1 0.885,0.125 1.104,0.281 0.219,0.156 10 false *2
*1 Engine Room Main Wire
*2 Engine Wire


Remove the nut and disconnect the engine room main wire with engine wire from the positive (+) battery terminal.


c.

Disengage the 2 claws to disconnect the engine room main wire from the engine wire.


d.

Remove the 2 nuts, battery clamp bolt and battery clamp sub-assembly from the battery carrier assembly.


e.

Remove the battery from the battery tray.


Hide 74431 21.REMOVE BATTERY TRAY

a.
A310644

Remove the battery tray from the battery carrier assembly.


Hide 74410 22.REMOVE BATTERY CARRIER ASSEMBLY

A304753

a.

Disengage the 6 clamps to disconnect the engine wire from the battery carrier assembly.


b.

Remove the 5 bolts and battery carrier assembly from the engine mounting insulator LH and vehicle.


Hide 17361M 23.SEPARATE AIR TUBE

A111182

a.

Remove the bolt to separate the air tube from the cylinder head cover sub-assembly.


Hide 24.DISCONNECT RADIATOR RESERVOIR TANK HOSE

Hide 16573B 25.DISCONNECT NO. 3 RADIATOR HOSE

A111184

a.

Loosen the hose clip and disconnect the No. 3 radiator hose from the water filler sub-assembly.


Hide 16572D 26.DISCONNECT NO. 2 RADIATOR HOSE

A111512

a.

Loosen the hose clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 87245 27.DISCONNECT INLET HEATER WATER HOSE

a.
A305927

Loosen the hose clip and disconnect the inlet heater water hose from the cylinder head sub-assembly.


Hide 87246 28.DISCONNECT OUTLET HEATER WATER HOSE

a.
A305930

Loosen the hose clip and disconnect the outlet heater water hose from the No. 1 water by-pass pipe.


Hide 23842A 29.REMOVE EFI FUEL PIPE CLAMP

Hide 23901 30.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 32941 31.DISCONNECT INLET NO. 1 OIL COOLER HOSE

Hide 32942 32.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 44772 33.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

A111514

a.

Loosen the hose clip and disconnect the check valve to connector tube hose from the booster vacuum tube.


Hide 16361A 34.REMOVE FAN AND GENERATOR V BELT

Hide 88320 35.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/o Fan Shroud Ventilation Duct)

A111513

a.

Disconnect the cooler compressor assembly connector.


b.

Remove the 3 bolts to separate the cooler compressor assembly from the oil pan sub-assembly.

HINT:

Separate the cooler compressor assembly together with the No. 1 cooler refrigerant discharge hose and No. 1 cooler refrigerant suction hose, then suspend them from the vehicle with a piece of rope.



Hide 88711 36.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Fan Shroud Ventilation Duct)

Hide 88712 37.DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (w/ Fan Shroud Ventilation Duct)

Hide 88320 38.REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Fan Shroud Ventilation Duct)

Hide 55550 39.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82121 40.DISCONNECT ENGINE WIRE

a.

Remove the relay block cover from the engine room relay block.


b.
A111519

Disengage the clamp to disconnect the engine wire from the vehicle.


c.

Disconnect the connector from the engine room relay block.


d.

Remove the nut from the engine room relay block.


e.

Disengage the 2 claws to disconnect the engine wire from the engine room relay block.


f.
A304755

Disconnect the 3 connectors as shown in the illustration.


g.

Disengage the 2 clamps to disconnect the engine wire from the wire harness clamp bracket and vehicle.


h.
A304743

Disengage the clamp to disconnect the engine wire from the wire harness clamp bracket.


i.

Disengage the grommet and pass the engine wire through the hole to the inside of the engine room.


j.
A304745

Disengage the 2 clamps to disconnect the engine wire from the engine mounting bracket LH.


k.

Remove the bolt to disconnect the engine wire from the automatic transaxle assembly.


Hide 58910C 41.REMOVE REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 42.REMOVE REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 57533B 43.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 44.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 33820B 45.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 43420 46.REMOVE FRONT DRIVE SHAFT ASSEMBLY

Hide 32101A 48.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 45259A 49.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45209 50.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45025D 51.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 52.REMOVE ENGINE ASSEMBLY WITH AUTOMATIC TRANSAXLE ASSEMBLY

a.
A112924

Loosen the engine moving control rod bolt.


b.
A304746C01
1.854,0 2.271,0 false
V100155

Attachment Placement Position


Place the height adjustment attachments or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with automatic transaxle assembly and front suspension crossmember sub-assembly.

NOTICE:
·

Place the height adjustment attachments or plate lift attachments so that the engine assembly with automatic transaxle assembly is level.

·

Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

As the engine assembly with automatic transaxle assembly is very heavy, be sure to support it securely.

·

To prevent deformation of the No. 2 oil pan sub-assembly, never set any attachments against the No. 2 oil pan sub-assembly of the engine assembly.

·

To prevent deformation of the automatic transaxle oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the automatic transaxle assembly.




c.
A112928

Remove the bolt and 2 nuts to disconnect the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


d.
A113660

Remove the through bolt and nut to disconnect the engine mounting insulator LH from the engine mounting bracket LH.

HINT:

Loosen by holding the nut and turning the through bolt.



e.
A305308

Remove the 6 bolts, engine assembly with automatic transaxle assembly and front suspension crossmember sub-assembly from the vehicle.

NOTICE:

When removing the engine assembly with automatic transaxle assembly and front suspension crossmember sub-assembly, be careful not to damage any engine wire or the steering shaft.



Hide 12281A 53.INSTALL NO. 1 ENGINE HANGER

a.

Separate the air fuel ratio sensor wire from the wire harness clamp bracket.


b.
A310645

Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.


c.
A105871C01
0.927,0.542 1.104,0.375 false 2.896,0.542 3.083,0.375 false 1.167,0.26 1.479,0.417 0.313,0.156 10 false *1 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.906,0.063 2.219,0.219 0.313,0.156 10 false *b 3.115,0.281 3.323,0.438 0.208,0.156 10 false *1
*1 No. 1 Engine Hanger
*a Front Side
*b Rear Side


Install the 2 No. 1 engine hangers to the cylinder head sub-assembly with the 2 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

HINT:
Part Name Part No.
No. 1 Engine Hanger 12281-0M020
Bolt 90119-T0011



Hide 51201 54.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

A304741

a.

Using an engine sling device and a chain block, suspend the engine assembly with automatic transaxle assembly.


b.

Remove the through bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.


Hide 82121 55.REMOVE ENGINE WIRE

A121490

a.

Remove the 2 bolts to disconnect the engine wire from the cylinder head sub-assembly.


b.

Disconnect all the engine wire and connectors. Make sure that no engine wire are connected to the engine.


Hide 12261 56.REMOVE VENTILATION HOSE

A259822

a.

Loosen the 2 hose clips and remove the ventilation hose from the cylinder head cover sub-assembly and intake manifold.


Hide 16502 57.REMOVE WATER FILLER SUB-ASSEMBLY

A116983

a.

Loosen the hose clip and disconnect the No. 1 radiator hose from the cylinder head sub-assembly.


b.

Remove the 2 nuts and water filler sub-assembly from the throttle body with motor assembly.


Hide 15301 58.REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 17111 59.REMOVE INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY

A117312

a.

Loosen the hose clip and disconnect the union to connector tube hose from the booster vacuum tube.


b.
A117313

Loosen the hose clip and disconnect the water by-pass hose from the cylinder head sub-assembly.


c.
A116984

Loosen the hose clip and disconnect the No. 2 water by-pass hose from the No. 1 water by-pass pipe.


d.
A302829

Remove the 3 bolts, 2 nuts and intake manifold with throttle body with motor assembly from the cylinder head sub-assembly.


e.

Remove the intake manifold to head gasket from the intake manifold.


Hide 17167 60.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25591 61.REMOVE MANIFOLD SUPPORT BRACKET

Hide 64.FIX ENGINE ASSEMBLY

A305920

a.

Use a lashing belt or a rope to secure the engine assembly to the engine lifter.

NOTICE:
·

Do not tighten the lashing belt or the rope any more than is necessary.




b.

Using a rope, engine sling device and a chain block, hold the automatic transaxle assembly.


c.

To enable removal of the automatic transaxle assembly, adjust the positions of the height adjustment attachments or plate lift attachments and set them in place.

NOTICE:
·

Place the height adjustment attachments or plate lift attachments so that the engine assembly with automatic transaxle assembly is level.

·

As the engine assembly with automatic transaxle assembly is very heavy, be sure to support it securely.

·

To prevent deformation of the No. 2 oil pan sub-assembly, never set any attachments against the No. 2 oil pan sub-assembly of the engine assembly.

·

To prevent deformation of the automatic transaxle oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the automatic transaxle assembly.




Hide 12321B 65.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

Hide 11363A 66.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 28100 67.REMOVE STARTER ASSEMBLY

Hide 68.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A305307

Remove the 2 bolts and 2 wire harness clamp brackets from the automatic transaxle assembly.


Hide 30500 69.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.
C283076E01
0.906,0.073 1.052,0.25 0.146,0.177 10 false A 2.365,0.031 2.51,0.208 0.146,0.177 10 false A 2.51,1.885 2.656,2.063 0.146,0.177 10 false B 2.167,2 2.313,2.177 0.146,0.177 10 false B 1.281,2 1.427,2.177 0.146,0.177 10 false B 0.646,0.906 0.792,1.083 0.146,0.177 10 true B 0.906,1.708 1.031,1.885 0.125,0.177 10 true B

Remove the 7 bolts and automatic transaxle assembly from the engine assembly.

NOTICE:

Do not allow the torque converter assembly to fall off.


HINT:
·

Bolt A: Remove from automatic transaxle assembly side

·

Bolt B: Remove from engine assembly side




Hide 32101 70.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using height adjustment attachments or plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustment attachments or plate lift attachments, place the engine assembly horizontally.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A166739E01
2.63,1.619 2.935,1.773 0.304,0.155 10 SST 1.954,2.054 2.592,1.726 false

Using SST, hold the crankshaft damper sub-assembly.

SST
09960-10010  (09962-01000, 09963-01000)


c.
A278687

Remove the 6 bolts, the rear drive plate spacer, the drive plate and ring gear sub-assembly, and the front drive plate spacer from the crankshaft.


Hide 71.INSTALL ENGINE STAND

a.

Using a sling device and a chain block, install the engine stand to the engine assembly.

NOTICE:
·

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.




Hide 12305 72.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A121468

Remove the 3 bolts and engine mounting insulator sub-assembly RH from the vehicle.


Hide 12372A 73.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Only perform this procedure when replacement of the engine mounting insulator LH is necessary.


a.
A121469

Remove the 5 bolts and engine mounting insulator LH from the vehicle.