Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333397 POWER STEERING SYSTEM(for TMT Made) S

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMT Made)  DIAGNOSTIC TROUBLE CODE CHART  


Power Steering System
DTC No. Detection Item DTC Detection Condition Warning Indicate Return-to-normal Condition Note Link
C1511 Torque Sensor1 Diagnosis Condition: IG ON
Malfunction Status: TRQ1 voltage is less than 0.25 V or more than 4.6 V
EPS warning light: Comes on Ignition switch ON again - Click here
C1512 Torque Sensor2 Diagnosis Condition: IG ON
Malfunction Status: TRQ2 voltage is less than 0.25 V or more than 4.6 V
EPS warning light: Comes on Ignition switch ON again - Click here
C1513 Torque Sensor Deviation Excessive Deviation of torque sensor TRQ1 and TRQ2 exceeds specified values EPS warning light: Comes on Ignition switch ON again - Click here
C1514 Torque Sensor Power Supply Voltage Diagnosis Condition: IG ON
Malfunction Status: TRQV voltage is less than 4.5 V or more than 5.5 V.
EPS warning light: Comes on Ignition switch ON again - Click here
C1515 Torque Sensor Zero Point Adjustment Undone This DTC is stored when torque sensor zero point calibration has not been performed. EPS warning light: Comes on Zero point calibration occurs There is no malfunction if this DTC is not output again after performing zero point calibration. Click here
C1516 Torque Sensor Zero Point Adjustment Incomplete Torque sensor zero point calibration is incomplete due to the steering wheel being touched during calibration. EPS warning light: Comes on Clear DTC There is no malfunction if this DTC is not output again after clearing the DTC and torque sensor calibration value, and performing zero point calibration. Click here
C1517 Torque Hold Temporary control due to malfunction related to torque sensor continues for long time EPS warning light: Comes on Ignition switch ON again - Click here
C1524 Motor Terminal Voltage Short (or open) in motor circuit or abnormal voltage in motor circuit EPS warning light: Comes on Ignition switch ON again - Click here
C1531 ECU Malfunction ECU internal malfunction
(CPU malfunction)
EPS warning light: Comes on Ignition switch ON again - Click here
C1532 ECU Malfunction ECU internal malfunction (Peripheral circuit malfunction) EPS warning light: Comes on Ignition switch ON again - Click here
C1533 Temperature Sensor Circuit is Low or High ECU internal malfunction
(Substrate temperature sensor malfunction)
EPS warning light: Comes on Ignition switch ON again and after normal confirmation - Click here
C1534 EEPROM ECU internal malfunction
(EEPROM error)
EPS warning light: Comes on Ignition switch ON again - Click here
C1535 ECU Malfunction ECU internal malfunction (Steering wheel location data error) EPS warning light: Comes on Ignition switch ON again - Click here
C1541 Vehicle Speed Signal Vehicle speed signals via CAN communication are cut off for 3 seconds or more. EPS warning light: Comes on The ECU judges the system has returned to normal or the ignition switch is turned ON again - Click here
C1542 Vehicle Speed Signal Malfunction Vehicle speed signals via CAN communication are cut off for 3 seconds or more. EPS warning light: Does not come on The ECU judges the system has returned to normal or the ignition switch is turned ON again - Click here
C1551 IG Power Supply Voltage Open or short in IG power source circuit with ignition switch ON EPS warning light: Comes on After normal confirmation - Click here
C1552 PIG Power Supply Voltage PIG power source circuit malfunction EPS warning light: Comes on After normal confirmation - Click here
C1553 PIG Power Supply Overvoltage
·

PIG power source overvoltage

·

IG power source overvoltage


EPS warning light: Comes on After normal confirmation - Click here
C1554 Power Supply Relay Failure Power source relay circuit malfunction EPS warning light: Comes on Ignition switch ON again - Click here
C1555 Motor Relay Welding Failure Predriver (Motor relay circuit) malfunction EPS warning light: Comes on Ignition switch ON again - Click here
C1571 Speed Sensor Malfunction (Test Mode DTC) Vehicle speed signals via CAN communication are cut off for 3 seconds or more. EPS warning light: Does not come on After test mode separation and after normal confirmation - Click here
C1581 Assist Map Number Un-Writing Assist map not written in power steering ECU assembly EPS warning light: Comes on Assist map written - Click here
C1582 Assist Map Number Mismatch Assist map number mismatch EPS warning light: Does not come on Ignition switch ON again - Click here
U0100 Lost Communication with ECM / PCM "A" Lost communication with ECM EPS warning light: When an error occurs during steering assist, the warning light does not illuminate. For errors that occur before assist (at the time of the decision to start assist), the warning light illuminates. After normal confirmation - Click here
U0129 Lost Communication with Brake System Control Module Lost communication with skid control ECU (Brake actuator assembly) EPS warning light: Comes on After normal confirmation - Click here