Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › 2020.03–2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422075 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BREATHER PLUG SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the continuously variable transaxle assembly.


a.
C428840

Install the breather plug sub-assembly to the continuously variable transaxle assembly.


Hide 35150B 2.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.
C428839C03
0.521,0.094 0.792,0.333 0.271,0.24 12 false *A 1.625,0.094 1.938,0.333 0.313,0.24 12 false *B
*A for Type A
*B for Type B


for Type A:

i.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission case plug assembly.

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Install the transmission case plug assembly to the continuously variable transaxle assembly.

NOTICE:

Be careful not to damage the O-ring.




b.

for Type B:

i.

Install the transmission case plug assembly to the continuously variable transaxle assembly.

NOTICE:

Be careful not to damage the O-ring.




Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 3 wire harness clamp brackets to the continuously variable transaxle assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 4.INSTALL CVT TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands and then apply MP grease to the entire periphery of the lip of a new CVT type T oil seal.


b.

Temporarily install the CVT type T oil seal by pressing it to the installation surface of the oil pump housing by hand.

NOTICE:

Be sure to install the CVT type T oil seal in the correct direction.



c.

Clean the CVT type T oil seal contact surface of SST and the area around it.

SST
09223-00010  


d.
C428783C01
1.667,2.583 1.667,2.167 false 0.844,2.667 1.156,2.823 0.313,0.156 10 false *a 1.583,2.594 1.896,2.75 0.313,0.156 10 false SST
*a Depth


Using SST and a hammer, drive the CVT type T oil seal in evenly, until it is even with the side surface of the transaxle housing.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Drive the CVT type T oil seal in gradually, while visually checking that it is even.

·

After installation, confirm that the CVT type T oil seal has been driven in until it is even with the side surface of the transaxle housing.

·

Wipe any extra grease off with your hand.




Hide 32000A 5.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C428784C01
1.323,0.458 1.823,0.167 true 2.469,0.521 2.771,0.979 true 1.833,0.052 2.146,0.208 0.313,0.156 10 false *a 2.24,0.427 2.427,0.604 0.188,0.177 10 true *b
*a Matchmark
*b Key


Set the key at the top of the drive sprocket and put a matchmark on the transaxle housing.


b.
C429298C01
1.396,0.177 1.552,0.177 1.552,0.177 1.75,0.5 false 1.417,2.021 1.573,2.021 1.573,2.021 1.74,1.667 false 1.25,0.083 1.542,0.313 0.292,0.229 10 false *a 1.26,1.948 1.531,2.125 0.271,0.177 10 false *b
*a Groove
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.

HINT:

The relative positions of the groove (*a) in the sleeve and the setblock will not necessarily be the same as in the illustration.



c.
C429299C03
1.24,0.719 0.458,0.198 0.458,0.198 1.25,0.479 true 2.354,1.365 1.635,1.948 1.635,1.948 2.375,1.063 true 1.49,1.896 1.802,2.052 0.313,0.156 10 false *1 0.271,0.104 0.563,0.281 0.292,0.177 10 false *a
*1 CVT Type T Oil Seal
*a Matchmark


Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT type T oil seal.




d.
C429300C01
1.292,0.417 1.552,0.104 1.552,0.104 1.698,0.104 true 1.271,1.604 1,1.927 1,1.927 0.844,1.927 true 2.365,1.052 1.646,1.958 1.646,1.958 2.365,1.365 true 1.51,1.885 1.74,2.073 0.229,0.188 10 false *1 1.698,0.021 1.958,0.219 0.26,0.198 10 false *a 0.688,1.844 0.948,2.042 0.26,0.198 10 true *a
*1 CVT Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT type T oil seal.




e.
C450689C01
1.313,0.698 0.625,0.229 0.625,0.229 1.333,0.479 true 2.448,1.375 1.5,1.99 1.5,1.99 2.438,1.115 true 1.354,1.927 1.656,2.135 0.302,0.208 10 false *1 0.469,0.115 0.781,0.323 0.313,0.208 10 false *a
*1 CVT Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the groove of the torque converter assembly into the key of the drive sprocket.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the CVT type T oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C435474N01
0.729,0.104 0.885,0.302 0.156,0.198 10 false A

Using a vernier caliper and straightedge, measure the dimension (A) between the set block and the end face of the continuously variable transaxle assembly.

NOTICE:

Make sure to deduct the thickness of the straightedge.



h.
C451164C01
0.573,2.073 0.24,2.417 true 2.646,1.49 2.385,1.573 false 2.865,0.438 3.042,0.563 false 0.906,0.771 1.375,0.406 true 2.698,0.333 2.896,0.5 0.198,0.167 10 false *a 0.052,2.354 0.24,2.521 0.188,0.167 10 false *b 2.906,1.875 3.094,2.042 0.188,0.167 10 false B 1.417,0.323 1.615,0.49 0.198,0.167 10 false *a 2.219,1.51 2.406,1.677 0.188,0.167 10 false *b
*a Engine Assembly Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (B) between the continuously variable transaxle assembly contact surface of the engine*a and the torque converter assembly contact surfaces of the drive plate*b, and check that dimension (B) is larger than dimension (A).

Standard:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 30400 6.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.

Using a transmission jack, support the continuously variable transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.

·

Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.




Hide 30400 7.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C435476C01
1.823,1.073 2.49,0.74 true 1.74,3.302 2.406,2.969 true 0.271,0.094 0.531,0.271 0.26,0.177 12 false *A 0.396,2.354 0.677,2.542 0.281,0.188 12 false *B 1.052,1.208 1.365,1.365 0.313,0.156 10 false *1 2.531,0.646 2.844,0.802 0.313,0.156 10 false *2 1.083,3.406 1.396,3.563 0.313,0.156 10 false *1 2.448,2.875 2.76,3.031 0.313,0.156 10 false *2
*A for Type A
*B for Type B
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum Grease Amount:

Approximately 1 g (0.0353 oz.)



b.
C435477C01
1.146,0.844 2.583,1.385 2.583,1.385 2.208,0.573 true 2.604,1.302 2.917,1.458 0.313,0.156 10 false *1 2.083,2.479 2.24,2.677 0.156,0.198 10 false A 2.51,4.104 2.667,4.302 0.156,0.198 10 false C 2.177,4.458 2.333,4.656 0.156,0.198 10 false B 0.813,2.74 0.969,2.938 0.156,0.198 10 false C 0.563,3.344 0.719,3.542 0.156,0.198 10 true C 0.813,4.125 0.969,4.323 0.156,0.198 10 true C 1.146,4.438 1.302,4.635 0.156,0.198 10 true C
*1 Knock Pin


Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.


c.

Install the continuously variable transaxle assembly to the engine assembly with the 7 bolts.

Torque:
Bolt (A) : 46 N*m (469 kgf*cm, 34 ft.*lbf)
Bolt (B) : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt (C) : 46 N*m (469 kgf*cm, 34 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.



HINT:
·

Bolt (A), (B): Install from continuously variable transaxle assembly side

·

Bolt (C): Install from engine assembly side




Hide 12372A 8.INSTALL ENGINE MOUNTING INSULATOR LH

a.
C428835C03
3.073,0.615 3.229,0.813 0.156,0.198 10 true 6 0.188,0.854 0.74,1.042 0.552,0.188 10 true 1 (*a), 5 1.146,0.938 1.302,1.135 0.156,0.198 10 true 3 3.104,1.438 3.26,1.635 0.156,0.198 10 true 4 2.208,1.969 2.365,2.167 0.156,0.198 10 true 2
*a Temporarily Tighten


Temporarily install the engine mounting insulator LH to the vehicle body with the bolts and nut.


b.

Fully tighten the bolts and nut in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
C428834E01
0.271,0.135 0.427,0.333 0.156,0.198 10 true 4 0.24,0.781 0.396,0.979 0.156,0.198 10 true 2 0.552,1.396 0.708,1.594 0.156,0.198 10 true 3 3.052,1.771 3.208,1.969 0.156,0.198 10 true 1

Temporarily install the engine mounting insulator LH to the continuously variable transaxle assembly with the 3 bolts and nut.


d.

Fully tighten the bolts and nut in the order shown in the illustration.

Torque:
Bolt : 42 N*m (428 kgf*cm, 31 ft.*lbf)
Nut : 20 N*m (204 kgf*cm, 15 ft.*lbf)


e.

Engage the clamp to connect the engine wire to the engine mounting insulator LH.


Hide 32101G 9.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Clean the threads of the 6 drive plate and torque converter assembly setting bolts.


b.
C321585C03
1.865,1.688 1.865,1.427 false 1.813,1.719 2.125,1.875 0.313,0.156 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 10.INSTALL FLYWHEEL HOUSING UNDER COVER

a.
C435479C01
0,0 0,0 false
V113147

Install in this Direction


Install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 12364B 12.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C435473C01
0.854,0.646 1.375,0.833 0.521,0.188 10 true 1(*a), 4 2.021,0.333 2.167,0.51 0.146,0.177 10 true 3 1.865,1.51 2.01,1.688 0.146,0.177 10 true 2
*a Temporarily Tighten


Install the No. 2 engine moving control rod to the continuously variable transaxle assembly with the 3 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 51201 13.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 14.REMOVE ENGINE SUPPORT BRIDGE

a.

Remove SST from the vehicle body.

NOTICE:

Prevent SST from contacting the vehicle body, windshield glass or upper front radiator support.



Hide 17410 17.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 51447D 18.INSTALL CENTER NO. 4 ENGINE UNDER COVER

Hide 19.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45260 20.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 21.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 28100 22.INSTALL STARTER ASSEMBLY

Hide 33823 23.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 16290F 24.CONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 16290F 25.CONNECT NO. 4 WATER BY-PASS HOSE

Hide 89535B 26.INSTALL TCM

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to connect all of the coolant system hoses before installing the TCM.


a.

Install the TCM to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 82121 27.CONNECT ENGINE WIRE

a.

Engage the 3 clamps to connect the engine wire to the front suspension crossmember sub-assembly.


b.

Engage the 3 clamps to connect the engine wire to the continuously variable transaxle assembly.


c.

Connect the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

Connect the No. 3 water by-pass hose assembly.


e.

Engage the 4 clamps to connect the engine wire to the continuously variable transaxle assembly.

C435478C01
2.635,0.073 2.813,0.24 0.177,0.167 10 true *1 2.938,0.76 3.125,0.927 0.188,0.167 10 true *2 2.948,1.333 3.135,1.49 0.188,0.156 10 true *3 3.719,0.75 3.906,0.906 0.188,0.156 10 true *4 3.083,1.844 3.271,2 0.188,0.156 10 true *5 4.354,1.823 4.542,1.99 0.188,0.167 10 true *6 2.667,2.583 2.854,2.75 0.188,0.167 10 true *7 2.188,2.313 2.375,2.469 0.188,0.156 10 true *8
*1 Transmission Wire Connector *2 Shift Stroke Sensor Connector
*3 Park/Neutral Position Switch Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 TCM Connector *6 Transmission Revolution Sensor (NSS) Connector
*7 Oil Pressure Sensor Connector *8 Transmission Revolution Sensor (NT) Connector
V113147

Install in this Direction - -



f.

Connect the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


g.

Connect the transmission revolution sensor (NT) connector.


h.

Connect the oil pressure sensor connector.


i.

Connect the transmission revolution sensor (NSS) connector.


j.

Connect the TCM connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the TCM connector makes a click sound.



k.

Connect the transmission revolution sensor (NOUT) connector.


l.

Connect the park/neutral position switch connector.


m.

Connect the shift stroke sensor connector.


n.

Connect the transmission wire connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 33820B 28.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 74404A 29.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 17701 31.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 32.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 55701J 33.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55815E 35.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 36.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 37.INSTALL FRONT WHEELS

Hide 38.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 39.ADD ENGINE COOLANT

Hide 40.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 42.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK

Hide 53876A 46.INSTALL FRONT FENDER LINER LH

Hide 53875A 47.INSTALL FRONT FENDER LINER RH

Hide 51442C 48.INSTALL ENGINE UNDER COVER LH

Hide 51441C 49.INSTALL ENGINE UNDER COVER RH

Hide 51451A 50.INSTALL CENTER ENGINE UNDER COVER

Hide 52.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 54. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART