Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _089412 M15A-FXE ENGINE MECHANICAL _0424635 CYLINDER HEAD GASKET A

M15A-FXE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking support brake system (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 17167 4.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 22030 7.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 8.REMOVE THROTTLE BODY GASKET

Hide 23250 9.REMOVE FUEL INJECTOR ASSEMBLY

Hide 11452D 12.REMOVE OIL LEVEL GAGE GUIDE

Hide 13.REMOVE NO. 1 WATER BY-PASS PIPE ASSEMBLY

Hide 16281 14.REMOVE NO. 4 WATER BY-PASS HOSE

Hide 12262 15.REMOVE NO. 2 VENTILATION HOSE

Hide 16.REMOVE WIRE HARNESS CLAMP BRACKET

Hide 11102A 17.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 18.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 19.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 20.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 13090E 21.REMOVE CAM TIMING CONTROL MOTOR O-RING

Hide 13470 22.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 11201 23.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 24.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 25.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320B 26.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 27.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 29.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13050 30.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 32.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 33.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 34.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 35.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 36.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 13478 37.REMOVE CRANKSHAFT PULLEY SPACER

Hide 11103 38.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13501A 40.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

Hide 13502B 41.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

Hide 11101 42.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 43.REMOVE CYLINDER HEAD GASKET

A466044

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 44.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 45.INSPECT CYLINDER HEAD SUB-ASSEMBLY