The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
| *a | Heavy object exceeding the capacity of the engine lifter |
Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.
If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.
| *a | High temperature areas |
Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.
Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3. DISCHARGE FUEL SYSTEM PRESSURE
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5.REMOVE FRONT WHEELS
51451A
6.REMOVE CENTER ENGINE UNDER COVER
51442C
7.REMOVE ENGINE UNDER COVER LH
51441C
8.REMOVE ENGINE UNDER COVER RH
9.DRAIN ENGINE OIL
10.DRAIN ENGINE COOLANT (for Engine)
11.DRAIN HYBRID TRANSAXLE FLUID
G9200
12.REMOVE INVERTER WITH CONVERTER ASSEMBLY
82662A
13.REMOVE NO. 1 RELAY BLOCK COVER
Remove the No. 1 relay block cover from the engine room relay block.
14.REMOVE ENGINE WIRE
Disconnect the 2 connectors from the engine room relay block.
Remove the nut.
Disengage the 4 claws to separate the engine wire from the engine room relay block.
Remove the 2 bolts to separate the engine wire from the vehicle.
Remove the clamp.
Disengage the clamp to separate the engine wire from the vehicle.
33820B
15.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Disengage the clamp to separate the transmission control cable assembly.
Remove the bolt to disconnect the transmission control cable assembly from the hybrid vehicle transaxle assembly.
Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.
Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.
16571C
16.DISCONNECT NO. 1 RADIATOR HOSE
Slide the clip and disconnect the No. 1 radiator hose from the water outlet.
16572D
17.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the water inlet sub-assembly.
G922H
18.DISCONNECT INLET HYBRID RADIATOR HOSE
Slide the clip and disconnect the inlet hybrid radiator hose from the motor cooling cooler.
G922F
19.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE
Slide the clip and disconnect the outlet No. 1 hybrid water pump hose from the motor cooling cooler.
23826
20.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
Disconnect the No. 1 fuel vapor feed hose from the fuel tank to canister tube.
77261D
21.DISCONNECT FUEL TANK TO CANISTER TUBE
Disengage the clamps to separate the fuel tank to canister tube from the engine wire.
16290F
22.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY
87245
23.DISCONNECT INLET HEATER WATER HOSE
23901
24.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp for the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pump assembly.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
88703
25.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
88704
26.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
27. SECURE STEERING WHEEL
45259A
28.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
29.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
17410
30.REMOVE FRONT EXHAUST PIPE ASSEMBLY
31.REMOVE DRIVE SHAFT ASSEMBLY
32.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the bolt and engine mounting stay LH.
Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.
Remove the 10 bolts to separate the front suspension crossmember sub-assembly from the vehicle.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
12353
33.REMOVE ENGINE MOUNTING BRACKET CAP
Turn over the engine mounting bracket cap to the upper part.
While rotating in the direction shown in the diagram, remove the engine mounting bracket cap.
34.INSTALL ENGINE HANGER
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
|
Bolt |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 91552-F1040 |
Attach an engine sling device and hang the engine assembly with transaxle with a chain block.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedure while the engine assembly with transaxle is suspended because doing so may cause the engine assembly with transaxle to drop, resulting in injury. However, the engine assembly with transaxle needs to be suspended when it is installed to or removed from an engine stand.
12372A
35.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Remove the 5 bolts, nut and engine mounting insulator LH from the vehicle.
G92A0A
36.DISCONNECT INVERTER RESERVE TANK ASSEMBLY
Remove the 2 bolts and disconnect the inverter reserve tank assembly.
12305
37.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the clamp and disconnect the air conditioner tube.
Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.
28193
38.REMOVE STARTER HOLE INSULATOR
11363A
39.REMOVE FLYWHEEL HOUSING SIDE COVER
821H2
40.REMOVE HV AIR CONDITIONING WIRE
82121
41.REMOVE ENGINE WIRE
Remove the 6 bolts.
Remove the bolt.
Remove the 3 bolts.
Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.
42.REMOVE WATER HOSE
Slide the 3 clips and remove the water hose from the engine assembly with transaxle.
43.REMOVE ENGINE ASSEMBLY
31270
44.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY
13405
45.REMOVE FLYWHEEL SUB-ASSEMBLY
19315
46.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
88370
47.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY
48.INSTALL ENGINE TO ENGINE STAND
Install the engine assembly to an engine stand.
49.REMOVE ENGINE HANGER
Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.