Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P023400  Turbocharger/Supercharger "A" Overboost Condition  


DESCRIPTION

Refer to DTC P003312.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P003312

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P023400 Turbocharger/Supercharger "A" Overboost Condition Boost pressure exceeds the threshold value (calculated from turbocharger speed upper limit value).
(1 trip detection logic)
·

Waste gate valve system

·

No. 2 turbo pressure sensor

·

Mass air flow meter sub-assembly

·

E.F.I. vacuum sensor assembly

·

Wire harness or connector

·

ECM


- SAE: P0234

MONITOR DESCRIPTION

If the boost pressure exceeds the threshold value (calculated from turbocharger speed upper limit value or compressor downstream temperature upper limit value), there may be a turbocharger system malfunction. In this case, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

A468662E04
2.865,1.688 2.656,1.323 2.656,1.323 2.458,1.323 false 0.25,0.292 1.354,0.542 1.104,0.25 10 false Vehicle Speed 0.76,0.677 1.375,0.875 0.615,0.198 10 false 50 km/h 0.927,2.042 1.542,2.24 0.615,0.198 10 false Idling 0.354,2.344 1.281,2.927 0.927,0.583 10 false Ignition switch ON 5.615,3.365 5.979,3.615 0.365,0.25 10 false [C] 1.427,1.26 2.729,1.563 1.302,0.302 10 false Fully depressed 2.198,1.885 2.656,2.083 0.458,0.198 10 false [A] 2.833,0.813 3.313,1.01 0.479,0.198 10 false [B]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

7.

Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P023400.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [B] and [C] again.




WIRING DIAGRAM

Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P010012

Refer to DTC P010012 for intake air temperature sensor (mass air flow meter sub-assembly) circuit.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P010012

Refer to DTC P012A11 for the E.F.I. vacuum sensor assembly circuit.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P012A11

Refer to DTC P023511 for No. 2 turbo pressure sensor circuit.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P023511

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P023400)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P023400 is output A
P023400 and other DTCs are output B


HINT:

If any DTCs other than P023400 are output, troubleshoot those DTCs first.




A

2.CLEAR DTC

B

GO TO DTC CHART

2.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

3.READ OUTPUT DTC
3.READ OUTPUT DTC
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Start the engine and wait 1 minute or more.

HINT:

At this time, waste gate valve active detection is performed to check for malfunctions in the waste gate valve system.



d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC is not output A
DTCs are output B




A

4.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)

B

GO TO DTC CHART

4.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
50003 372 229

b.

Using the table, read the normal atmospheric pressure value for the applicable altitude and temperature.

A337505

HINT:
·

Standard atmospheric pressure is approximately 101 kPa(abs) (15 psi(abs)).

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.15 psi). This varies by weather.




c.

Compare the Atmospheric pressure value in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Other than the following A
Difference between Atmospheric Pressure in the Data List and normal atmospheric pressure value is 10 kPa (1.45 psi) or more. B




A

5.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)

B

5.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
50003 372 214

b.

Read the Data List after cooling the engine sufficiently.

Result:
Result Proceed to
Other than the following A
Difference between Intake Air Temperature in the Data List and actual outside air temperature value is 15°C (27°F) or more. B




A

6.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

B

17.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)
6.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Inspect the mass air flow meter sub-assembly, referring to On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter sub-assembly, referring to Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 2 TURBO PRESSURE SENSOR

NG

15.CHECK HARNESS AND CONNECTOR
7.INSPECT NO. 2 TURBO PRESSURE SENSOR

Result:
Proceed to
OK
NG



OK

8.INSPECT E.F.I. VACUUM SENSOR ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR
8.INSPECT E.F.I. VACUUM SENSOR ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

9.CLEAR DTC

NG

11.CHECK HARNESS AND CONNECTOR
9.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P023400)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P023400)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P023400.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P023400 is output)
B




A

END

B

11.CHECK HARNESS AND CONNECTOR
a.

Disconnect the E.F.I. vacuum sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D93-3(VC) - D93-1(E2) Ignition switch ON 4.5 to 5.5 V
D93-2(PIC) - D93-1(E2) Ignition switch ON 3.0 to 5.5 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D93-3(VC) - D93-2(PIC) Ignition switch off 171 to 189 kΩ
D93-1(E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE E.F.I. VACUUM SENSOR ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (E.FI. VACUUM SENSOR ASSEMBLY - ECM)
12.CHECK HARNESS AND CONNECTOR (E.FI. VACUUM SENSOR ASSEMBLY - ECM)
a.

Disconnect the E.F.I. vacuum sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D93-3(VC) - D104-82(VCPR) Always Below 1 Ω
D93-2(PIC) - D104-105(PIC) Always Below 1 Ω
D93-1(E2) - D104-81(EPIC) Always Below 1 Ω
D93-3(VC) or D104-82(VCPR) - Body ground and other terminals Always 10 kΩ or higher
D93-2(PIC) or D104-105(PIC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR
a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D94-3(VC) - D94-2(E2) Ignition switch ON 4.5 to 5.5 V
D94-1(PTA) - D94-2(E2) Ignition switch ON 3.0 to 5.5 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D94-3(VC) - D94-1(PTA) Ignition switch off 171 to 189 kΩ
D94-2(E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

14.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
14.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D94-3(VC) - D104-80(VPTA) Always Below 1 Ω
D94-1(PTA) - D104-103(PTA) Always Below 1 Ω
D94-2(E2) - D104-79(EPTA) Always Below 1 Ω
D94-3(VC) or D104-80(VPTA) - Body ground and other terminals Always 10 kΩ or higher
D94-1(PTA) or D104-103(PTA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D23-3(VCC) - D23-2(E2G) Ignition switch ON 4.8 to 5.2 V
D23-1(FG) - D23-2(E2G) Ignition switch ON 4.8 to 5.2 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-3(VCC) - D23-1(FG) Ignition switch off 2.09 to 2.31 kΩ
D23-2(E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-3(VCC) - D104-84(VCVG) Always Below 1 Ω
D23-1(FG) - D104-107(VG) Always Below 1 Ω
D23-2(E2G) - D104-83(E2G) Always Below 1 Ω
D23-3(VCC) or D104-84(VCVG) - Body ground and other terminals Always 10 kΩ or higher
D23-1(FG) or D104-107(VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter sub-assembly (intake air temperature sensor).

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-4(THA) - D104-106(THA) Always Below 1 Ω
D23-2(E2G) - D104-83(E2G) Always Below 1 Ω
D23-4(THA) or D104-106(THA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR