Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2021.11
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM J

G16E-GTS ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A477654E01
1.302,0.833 3.115,1.135 1.813,0.302 10 false from EFI NO. 1 Fuse 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.563,3.031 2.427,0.385 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.865,1.042 3.698,1.396 0.833,0.354 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R 0.896,1.198 2.729,1.51 1.833,0.313 10 false from EFI-MAIN NO. 1 Relay

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit

·

VC Output Circuit

A425734E21
0.448,0.198 0.823,0.396 0.375,0.198 10 false D19 0.448,0.385 1.969,0.771 1.521,0.385 10 false Throttle Body with Motor Assembly 0.458,1.781 0.771,1.979 0.313,0.198 10 false f1 0.448,1.969 2.229,2.188 1.781,0.219 10 false Crankshaft Position Sensor 0.458,3.052 0.771,3.25 0.313,0.198 10 false D90 0.448,3.24 2.063,3.625 1.615,0.385 10 false Camshaft Position Sensor (for Intake Camshaft) 0.448,4.365 0.76,4.563 0.313,0.198 10 false D91 0.458,4.552 2.073,4.938 1.615,0.385 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.448,5.646 0.792,5.854 0.344,0.208 10 false D95 0.458,5.833 2.531,6.198 2.073,0.365 10 false No. 1 Turbo Pressure Sensor 0.469,6.969 1.177,7.188 0.708,0.219 10 false D110 0.458,7.156 2,7.75 1.542,0.594 10 false Engine Oil Pressure and Temperature Sensor 2.542,0.281 2.844,0.5 0.302,0.219 10 false VC 2.542,0.667 2.844,0.833 0.302,0.167 10 false E2 2.469,1 2.917,1.167 0.448,0.167 10 false VTA 2.406,1.375 2.844,1.573 0.438,0.198 10 false VTA2 2.865,0.531 3.115,0.698 0.25,0.167 10 false 3 2.865,0.177 3.115,0.344 0.25,0.167 10 false 5 2.875,0.906 3.125,1.073 0.25,0.167 10 false 6 2.865,1.26 3.115,1.427 0.25,0.167 10 false 4 2.875,1.781 3.125,1.948 0.25,0.167 10 false 3 2.896,2.146 3.146,2.313 0.25,0.167 10 false 2 2.865,2.521 3.115,2.688 0.25,0.167 10 false 1 2.875,3.052 3.125,3.219 0.25,0.167 10 false 3 2.865,3.417 3.115,3.583 0.25,0.167 10 false 2 2.865,3.76 3.115,3.927 0.25,0.167 10 false 1 2.865,4.729 3.115,4.896 0.25,0.167 10 false 2 2.885,5.073 3.135,5.24 0.25,0.167 10 false 1 2.875,4.354 3.125,4.521 0.25,0.167 10 false 3 2.854,5.646 3.104,5.813 0.25,0.167 10 false 3 2.854,6.021 3.104,6.188 0.25,0.167 10 false 2 2.885,6.375 3.135,6.542 0.25,0.167 10 false 1 2.875,6.969 3.125,7.135 0.25,0.167 10 false 3 2.854,7.313 3.104,7.479 0.25,0.167 10 false 2 2.865,7.708 3.115,7.875 0.25,0.167 10 false 1 2.865,8.094 3.115,8.26 0.25,0.167 10 false 4 2.365,1.885 2.854,2.083 0.49,0.198 10 false VCNE 2.49,2.24 2.865,2.427 0.375,0.188 10 false NE- 2.469,2.615 2.854,2.844 0.385,0.229 10 false NE+ 2.531,3.167 2.854,3.375 0.323,0.208 10 false VC 2.448,3.521 2.854,3.76 0.406,0.24 10 false VVI- 2.438,3.885 2.833,4.104 0.396,0.219 10 false VVI+ 2.458,4.469 2.844,4.667 0.385,0.198 10 false VC2 2.375,4.833 2.844,5.083 0.469,0.25 10 false VVE- 2.365,5.208 2.823,5.438 0.458,0.229 10 false VVE+ 2.531,5.75 2.844,5.99 0.313,0.24 10 false VC 2.542,6.115 2.844,6.365 0.302,0.25 10 false E2 2.479,6.479 2.844,6.74 0.365,0.26 10 false PIM 2.531,7.083 2.865,7.333 0.333,0.25 10 false VC 2.542,7.448 2.875,7.698 0.333,0.25 10 false E2 2.438,7.823 2.823,8.01 0.385,0.188 10 false PEO 2.375,8.219 2.833,8.51 0.458,0.292 10 false THEO 4.958,0.177 5.229,0.344 0.271,0.167 10 false 109 4.948,0.531 5.219,0.698 0.271,0.167 10 false 110 4.938,0.906 5.208,1.073 0.271,0.167 10 false 108 5,1.26 5.198,1.427 0.198,0.167 10 false 87 4.927,1.771 5.198,1.938 0.271,0.167 10 false 116 4.927,2.135 5.198,2.302 0.271,0.167 10 false 115 4.99,2.51 5.188,2.677 0.198,0.167 10 false 92 4.99,3.052 5.188,3.219 0.198,0.167 10 false 88 5,3.417 5.198,3.583 0.198,0.167 10 false 89 5,3.781 5.198,3.948 0.198,0.167 10 false 90 4.917,4.354 5.188,4.521 0.271,0.167 10 false 113 4.927,4.729 5.198,4.896 0.271,0.167 10 false 114 4.979,5.094 5.177,5.26 0.198,0.167 10 false 91 5,5.635 5.271,5.802 0.271,0.167 10 false 75 4.99,6 5.26,6.167 0.271,0.167 10 false 76 5.01,6.375 5.281,6.542 0.271,0.167 10 false 98 5.01,6.969 5.281,7.25 0.271,0.281 10 false 77 5.021,7.344 5.365,7.771 0.344,0.427 10 false 78 4.938,7.708 5.302,7.938 0.365,0.229 10 false 100 4.958,8.094 5.313,8.344 0.354,0.25 10 false 101 5.333,8.635 5.75,8.813 0.417,0.177 10 false D104 5.823,8.635 6.167,8.813 0.344,0.177 10 false ECM 6.271,0.146 6.542,0.313 0.271,0.167 10 false 5 V 5.281,0.177 5.688,0.354 0.406,0.177 10 false VCTA 5.281,0.542 5.604,0.719 0.323,0.177 10 false ETA 5.292,1.01 5.677,1.198 0.385,0.188 10 false VTA1 5.281,1.375 5.667,1.563 0.385,0.188 10 false VTA2 5.281,1.781 5.708,1.958 0.427,0.177 10 false VCNE 5.281,2.156 5.594,2.333 0.313,0.177 10 false NE- 5.292,2.615 5.604,2.792 0.313,0.177 10 false NE+ 5.292,3.063 5.719,3.24 0.427,0.177 10 false VCV1 5.292,3.427 5.719,3.604 0.427,0.177 10 false VV1- 5.292,3.896 5.719,4.073 0.427,0.177 10 false VV1+ 5.292,4.375 5.719,4.552 0.427,0.177 10 false VCE1 5.281,4.74 5.708,4.917 0.427,0.177 10 false EV1- 5.281,5.198 5.708,5.375 0.427,0.177 10 false EV1+ 5.292,5.646 5.75,5.833 0.458,0.188 10 false VCPM 5.292,6.01 5.708,6.188 0.417,0.177 10 false EPIM 5.292,6.479 5.615,6.667 0.323,0.188 10 false PIM 5.292,6.969 5.729,7.156 0.438,0.188 10 false VCPE 5.281,7.333 5.719,7.521 0.438,0.188 10 false EPEO 5.292,7.813 5.646,8 0.354,0.188 10 false PEO 5.281,8.208 5.729,8.396 0.448,0.188 10 false THEO

A468623E02
0.469,0.719 0.927,0.917 0.458,0.198 10 false A62 0.469,0.906 2.094,1.521 1.625,0.615 10 false Accelerator Pedal Sensor Assembly 2.458,1.5 2.865,1.75 0.406,0.25 10 false EPA 2.385,1.854 2.823,2.146 0.438,0.292 10 false EPA2 2.458,2.219 2.833,2.458 0.375,0.24 10 false VPA 2.396,2.573 2.844,2.813 0.448,0.24 10 false VPA2 2.896,1.396 3.177,1.615 0.281,0.219 10 false 5 2.896,1.75 3.177,1.969 0.281,0.219 10 false 2 2.896,2.115 3.177,2.333 0.281,0.219 10 false 6 2.906,2.469 3.188,2.688 0.281,0.219 10 false 3 4.969,1.688 5.25,1.906 0.281,0.219 10 false 59 4.958,1.323 5.24,1.542 0.281,0.219 10 false 56 4.969,2.063 5.25,2.281 0.281,0.219 10 false 55 4.969,2.417 5.25,2.635 0.281,0.219 10 false 58 5.323,1.385 5.729,1.604 0.406,0.219 10 false EPA 5.323,1.75 5.729,1.969 0.406,0.219 10 false EPA2 5.323,2.219 5.729,2.438 0.406,0.219 10 false VPA 5.323,2.573 5.729,2.792 0.406,0.219 10 false VPA2 0.469,3.115 0.927,3.313 0.458,0.198 10 false D23 0.469,3.302 1.781,3.896 1.313,0.594 10 false Mass Air Flow Meter Sub-assembly 2.479,3.146 2.823,3.385 0.344,0.24 10 false VCC 2.49,3.51 2.833,3.802 0.344,0.292 10 false E2G 2.573,3.875 2.875,4.115 0.302,0.24 10 false FG 2.5,4.24 2.917,4.5 0.417,0.26 10 false THA 5.323,3.042 5.823,3.25 0.5,0.208 10 false VCVG 5.323,3.406 5.729,3.625 0.406,0.219 10 false E2G 5.323,3.885 5.729,4.104 0.406,0.219 10 false VG 5.323,4.24 5.729,4.458 0.406,0.219 10 false THA 2.906,3.052 3.188,3.271 0.281,0.219 10 false 3 2.917,3.417 3.198,3.635 0.281,0.219 10 false 2 2.906,3.771 3.188,3.99 0.281,0.219 10 false 1 2.917,4.135 3.198,4.354 0.281,0.219 10 false 4 4.958,2.99 5.229,3.188 0.271,0.198 10 false 84 4.969,3.354 5.24,3.552 0.271,0.198 10 false 83 4.917,3.719 5.198,3.938 0.281,0.219 10 false 107 4.917,4.083 5.198,4.302 0.281,0.219 10 false 106 0.469,4.656 0.927,4.854 0.458,0.198 10 false D97 0.469,4.844 2.115,5.344 1.646,0.5 10 false Fuel Pressure Sensor (for High Pressure Side) 2.563,4.688 2.865,4.927 0.302,0.24 10 false VC 2.573,5.052 2.844,5.292 0.271,0.24 10 false E2 2.552,5.406 2.958,5.625 0.406,0.219 10 false PR 5.323,4.583 5.729,4.802 0.406,0.219 10 false VCPR 5.323,4.958 5.729,5.177 0.406,0.219 10 false EPR 5.323,5.417 5.729,5.635 0.406,0.219 10 false PR 2.896,4.604 3.177,4.823 0.281,0.219 10 false 1 2.917,4.938 3.198,5.156 0.281,0.219 10 false 2 2.906,5.323 3.188,5.542 0.281,0.219 10 false 3 4.958,4.521 5.229,4.719 0.271,0.198 10 false 96 4.969,4.896 5.24,5.094 0.271,0.198 10 false 73 4.958,5.26 5.229,5.458 0.271,0.198 10 false 97 0.469,5.917 0.927,6.115 0.458,0.198 10 false E4 0.469,6.104 2.208,6.677 1.74,0.573 10 false No. 2 Fuel Pressure Sensor (for Low Pressure Side) 2.563,5.958 2.865,6.198 0.302,0.24 10 false VC 2.583,6.313 2.854,6.552 0.271,0.24 10 false E2 2.896,5.833 3.177,6.052 0.281,0.219 10 false 1 2.896,6.198 3.177,6.417 0.281,0.219 10 false 3 2.906,6.573 3.188,6.792 0.281,0.219 10 false 2 5.313,5.854 5.719,6.073 0.406,0.219 10 false VCPF 5.313,6.219 5.719,6.438 0.406,0.219 10 false EPFL 5.313,6.677 5.719,6.896 0.406,0.219 10 false PFL 4.938,5.781 5.208,5.979 0.271,0.198 10 false 120 4.938,6.156 5.208,6.354 0.271,0.198 10 false 119 4.938,6.51 5.219,6.729 0.281,0.219 10 false 121 5.76,8.354 6.906,8.688 1.146,0.333 10 false ECM 2.49,6.677 2.896,6.896 0.406,0.219 10 false PFL 2.385,1.135 3,1.333 0.615,0.198 10 false VCP2 2.365,0.781 2.979,0.979 0.615,0.198 10 false VCPA 2.885,1.01 3.042,1.208 0.156,0.198 10 false 1 2.885,0.656 3.042,0.854 0.156,0.198 10 false 4 5.323,1.021 5.938,1.219 0.615,0.198 10 false VCP2 5.323,0.656 5.938,0.854 0.615,0.198 10 false VCPA 4.958,0.969 5.271,1.167 0.313,0.198 10 false 60 4.979,0.594 5.292,0.792 0.313,0.198 10 false 57 4.875,0.76 5.333,0.958 0.458,0.198 10 false A106 4.885,3.156 5.344,3.354 0.458,0.198 10 false D104 4.958,7.042 5.229,7.24 0.271,0.198 10 false 43 4.958,7.417 5.229,7.615 0.271,0.198 10 false 44 4.958,7.781 5.26,7.979 0.302,0.198 10 false 52 2.885,7.094 3.167,7.313 0.281,0.219 10 false 3 2.885,7.469 3.167,7.688 0.281,0.219 10 false 1 2.896,7.844 3.177,8.063 0.281,0.219 10 false 2 2.469,7.208 2.875,7.427 0.406,0.219 10 false VDO 2.458,7.583 2.865,7.802 0.406,0.219 10 false GND 2.469,7.948 2.875,8.167 0.406,0.219 10 false OUT 0.469,7.177 0.875,7.396 0.406,0.219 10 false A107 0.469,7.365 2.24,7.969 1.771,0.604 10 false Clutch Pedal Stroke Sensor Assembly 5.313,7.104 5.823,7.323 0.51,0.219 10 false VCCL 5.313,7.49 5.823,7.708 0.51,0.219 10 false E2CL 5.323,7.927 5.833,8.146 0.51,0.219 10 false CLS 4.885,7.208 5.344,7.406 0.458,0.198 10 false A106 4.896,7.583 5.354,7.781 0.458,0.198 10 false A106 4.896,7.948 5.354,8.146 0.458,0.198 10 false A106 4.885,1.125 5.344,1.323 0.458,0.198 10 false A106 4.875,1.49 5.333,1.688 0.458,0.198 10 false A106 4.875,1.854 5.333,2.052 0.458,0.198 10 false A106 4.875,2.219 5.333,2.417 0.458,0.198 10 false A106 4.885,2.583 5.344,2.781 0.458,0.198 10 false A106 4.885,3.521 5.344,3.719 0.458,0.198 10 false D104 4.885,3.885 5.344,4.083 0.458,0.198 10 false D104 4.885,4.25 5.344,4.448 0.458,0.198 10 false D104 4.896,4.688 5.354,4.885 0.458,0.198 10 false D104 4.885,5.063 5.344,5.26 0.458,0.198 10 false D104 4.896,5.427 5.354,5.625 0.458,0.198 10 false D104 4.906,5.948 5.365,6.146 0.458,0.198 10 false D104 4.896,6.323 5.354,6.521 0.458,0.198 10 false D104 4.896,6.688 5.354,6.885 0.458,0.198 10 false D104

A468624E02
5.896,4.906 6.948,5.313 1.052,0.406 10 false ECM 4.969,0.885 5.583,1.083 0.615,0.198 10 false A106 4.969,1.25 5.583,1.448 0.615,0.198 10 false A106 4.969,1.615 5.583,1.813 0.615,0.198 10 false A106 4.979,2.146 5.594,2.344 0.615,0.198 10 false D104 4.99,2.521 5.604,2.719 0.615,0.198 10 false D104 4.99,2.885 5.604,3.083 0.615,0.198 10 false D104 4.99,3.406 5.604,3.604 0.615,0.198 10 false D104 4.99,3.771 5.604,3.969 0.615,0.198 10 false D104 4.99,4.146 5.604,4.344 0.615,0.198 10 false D104 0.563,0.854 1.177,1.052 0.615,0.198 10 false D66 0.563,2.104 1.177,2.302 0.615,0.198 10 false D93 0.563,3.365 1.177,3.563 0.615,0.198 10 false D94 0.563,1.031 1.854,1.615 1.292,0.583 10 false Differential Pressure Sensor*1 0.563,2.292 1.969,2.854 1.406,0.563 10 false E.F.I. Vacuum Sensor Assembly 0.563,3.552 2.51,4.01 1.948,0.458 10 false No. 2 Turbo Pressure Sensor 2.458,0.896 3.073,1.094 0.615,0.198 10 false VCDR 2.583,1.25 3.198,1.448 0.615,0.198 10 false E2R 2.552,1.604 3.167,1.802 0.615,0.198 10 false VPR 2.99,0.781 3.604,0.979 0.615,0.198 10 false 3 2.99,1.135 3.604,1.333 0.615,0.198 10 false 1 3,1.51 3.615,1.708 0.615,0.198 10 false 2 5.042,0.708 5.667,0.906 0.625,0.198 10 false 48 5.042,1.094 5.667,1.292 0.625,0.198 10 false 47 5.042,1.448 5.667,1.646 0.625,0.198 10 false 37 5.406,0.771 6.031,0.969 0.625,0.198 10 false VCPX*1 5.406,1.135 6.031,1.333 0.625,0.198 10 false EPEX*1 5.406,1.604 6.031,1.802 0.625,0.198 10 false PEX*1 2.979,2.771 3.594,2.969 0.615,0.198 10 false 2 2.99,3.667 3.604,3.865 0.615,0.198 10 false 2 2.979,2.01 3.594,2.208 0.615,0.198 10 false 3 2.99,3.292 3.604,3.49 0.615,0.198 10 false 3 2.979,2.375 3.594,2.573 0.615,0.198 10 false 1 3,4.01 3.615,4.208 0.615,0.198 10 false 1 2.635,2.167 3.25,2.365 0.615,0.198 10 false VC 2.656,2.51 3.271,2.708 0.615,0.198 10 false E2 2.615,2.875 3.229,3.073 0.615,0.198 10 false PIC 2.635,3.406 3.25,3.604 0.615,0.198 10 false VC 2.667,3.75 3.281,3.948 0.615,0.198 10 false E2 2.573,4.104 3.188,4.302 0.615,0.198 10 false PTA 5.406,4.135 6.021,4.333 0.615,0.198 10 false PTA 5.406,3.667 6.021,3.865 0.615,0.198 10 false EPTA 5.406,3.302 6.021,3.5 0.615,0.198 10 false VPTA 5.406,2.875 6.021,3.073 0.615,0.198 10 false PIC 5.406,2.406 6.021,2.604 0.615,0.198 10 false EPIC 5.406,2.042 6.021,2.24 0.615,0.198 10 false VCPC 5.052,1.958 5.677,2.156 0.625,0.198 10 false 82 5.052,2.344 5.677,2.542 0.625,0.198 10 false 81 5.042,2.719 5.667,2.917 0.625,0.198 10 false 105 5.063,3.229 5.688,3.427 0.625,0.198 10 false 80 5.052,3.594 5.677,3.792 0.625,0.198 10 false 79 5,3.969 5.625,4.167 0.625,0.198 10 false 103 0.323,5.208 3.042,5.469 2.719,0.26 10 false *1: w/ Gasoline Particulate Filter


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 1 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 1 FUSE VOLTAGE
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI NO. 1 fuse) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Check the fuse with it installed to the No. 1 engine room relay block assembly.

·

If the result is not as specified, since current is not flowing to the +B terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:
·

When cleaning or replacing one throttle body with motor assembly, clean the other throttle body with motor assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P210900

·

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




A

4.CHECK COMMUNICATION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK COMMUNICATION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK COMMUNICATION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

5.CHECK COMMUNICATION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK COMMUNICATION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

6.CHECK COMMUNICATION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK COMMUNICATION BETWEEN GTS AND ECM (NO. 1 TURBO PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

7.CHECK COMMUNICATION BETWEEN GTS AND ECM (NO. 1 TURBO PRESSURE SENSOR)
a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)

B

8.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)
a.

Disconnect the engine oil pressure and temperature sensor connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK COMMUNICATION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE ENGINE OIL PRESSURE AND TEMPERATURE SENSOR

9.CHECK COMMUNICATION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK COMMUNICATION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

10.CHECK COMMUNICATION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

11.CHECK COMMUNICATION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

11.CHECK COMMUNICATION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (for high pressure side) connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

12.CHECK COMMUNICATION BETWEEN GTS AND ECM (NO. 2 FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))

B

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

12.CHECK COMMUNICATION BETWEEN GTS AND ECM (NO. 2 FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))
a.

Disconnect the No. 2 fuel pressure sensor (for low pressure side) connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the No. 2 fuel pressure sensor (for low pressure side).

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

13.CHECK COMMUNICATION BETWEEN GTS AND ECM (CLUTCH PEDAL STROKE SENSOR ASSEMBLY)

B

REPLACE NO. 2 FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE)

13.CHECK COMMUNICATION BETWEEN GTS AND ECM (CLUTCH PEDAL STROKE SENSOR ASSEMBLY)
a.

Disconnect the clutch pedal stroke sensor assembly connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the turbocharger sub-assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

14.CHECK COMMUNICATION BETWEEN GTS AND ECM (E.F.I. VACUUM SENSOR ASSEMBLY)

B

REPLACE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

14.CHECK COMMUNICATION BETWEEN GTS AND ECM (E.F.I. VACUUM SENSOR ASSEMBLY)
a.

Disconnect the E.F.I. vacuum sensor assembly connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

15.CHECK COMMUNICATION BETWEEN GTS AND ECM (NO. 2 TURBO PRESSURE SENSOR)

B

REPLACE E.F.I. VACUUM SENSOR ASSEMBLY

15.CHECK COMMUNICATION BETWEEN GTS AND ECM (NO. 2 TURBO PRESSURE SENSOR)
a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible (w/ Gasoline Particulate Filter) A
Communication is not possible (w/o Gasoline Particulate Filter) B
Communication is possible C



A

16.REPLACE CONNECTION BETWEEN GTS AND ECM (DIFFERENTIAL PRESSURE SENSOR)

B

18.CHECK HARNESS AND CONNECTOR

C

16.REPLACE CONNECTION BETWEEN GTS AND ECM (DIFFERENTIAL PRESSURE SENSOR)
a.

Disconnect the differential pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

17.CHECK HARNESS AND CONNECTOR

B

17.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the crankshaft position sensor connector.


c.

Disconnect the camshaft position sensor (for intake camshaft) connector.


d.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


e.

Disconnect the No. 1 turbo pressure sensor connector.


f.

Disconnect the engine oil pressure and temperature sensor connector.


g.

Disconnect the accelerator pedal sensor assembly connector.


h.

Disconnect the mass air flow meter sub-assembly connector.


i.

Disconnect the fuel pressure sensor (for high pressure side) connector.


j.

Disconnect the No. 2 fuel pressure sensor (for low pressure side) connector.


k.

Disconnect the clutch pedal stroke sensor assembly connector.


l.

Disconnect the E.F.I. vacuum sensor assembly connector.


m.

Disconnect the No. 2 turbo pressure sensor connector.


n.

Disconnect the differential pressure sensor connector.


o.

Disconnect the ECM connectors.


p.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block assembly.


q.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D104-109(VCTA) - Body ground Always 10 kΩ or higher
D104-116(VCNE) - Body ground Always 10 kΩ or higher
D104-88(VCV1) - Body ground Always 10 kΩ or higher
D104-113(VCE1) - Body ground Always 10 kΩ or higher
D104-75(VCPM) - Body ground Always 10 kΩ or higher
D104-77(VCPE) - Body ground Always 10 kΩ or higher
A106-57(VCPA) - Body ground Always 10 kΩ or higher
D104-84(VCVG) - Body ground Always 10 kΩ or higher
D104-96(VCPR) - Body ground Always 10 kΩ or higher
D104-120(VCPF) - Body ground Always 10 kΩ or higher
A106-43(VCCL) - Body ground Always 10 kΩ or higher
A104-82(VCPC) - Body ground Always 10 kΩ or higher
A104-80(VPTA) - Body ground Always 10 kΩ or higher
A106-43(VCPX) - Body ground Always 10 kΩ or higher
5(EFI-MAIN NO. 1 relay) - A106-9(+B) Always Below 1 Ω
5(EFI-MAIN NO. 1 relay) - A106-35(+B2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the crankshaft position sensor connector.


c.

Disconnect the camshaft position sensor (for intake camshaft) connector.


d.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


e.

Disconnect the No. 1 turbo pressure sensor connector.


f.

Disconnect the engine oil pressure and temperature sensor connector.


g.

Disconnect the accelerator pedal sensor assembly connector.


h.

Disconnect the mass air flow meter sub-assembly connector.


i.

Disconnect the fuel pressure sensor (for high pressure side) connector.


j.

Disconnect the No. 2 fuel pressure sensor (for low pressure side) connector.


k.

Disconnect the clutch pedal stroke sensor assembly connector.


l.

Disconnect the E.F.I. vacuum sensor assembly connector.


m.

Disconnect the No. 2 turbo pressure sensor connector.


n.

Disconnect the ECM connectors.


o.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block assembly.


p.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D104-109(VCTA) - Body ground Always 10 kΩ or higher
D104-116(VCNE) - Body ground Always 10 kΩ or higher
D104-88(VCV1) - Body ground Always 10 kΩ or higher
D104-113(VCE1) - Body ground Always 10 kΩ or higher
D104-75(VCPM) - Body ground Always 10 kΩ or higher
D104-77(VCPE) - Body ground Always 10 kΩ or higher
A106-57(VCPA) - Body ground Always 10 kΩ or higher
D104-84(VCVG) - Body ground Always 10 kΩ or higher
D104-96(VCPR) - Body ground Always 10 kΩ or higher
D104-120(VCPF) - Body ground Always 10 kΩ or higher
A106-43(VCCL) - Body ground Always 10 kΩ or higher
A104-82(VCPC) - Body ground Always 10 kΩ or higher
A104-80(VPTA) - Body ground Always 10 kΩ or higher
5(EFI-MAIN NO. 1 relay) - A106-9(+B) Always Below 1 Ω
5(EFI-MAIN NO. 1 relay) - A106-35(+B2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR