Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING ECU (for LHD) › from 2020.09
RM36W0E _55 Steering _087549 POWER ASSIST SYSTEMS _0432876 POWER STEERING ECU(for LHD) A

POWER ASSIST SYSTEMS  POWER STEERING ECU(for LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 45254B 1.INSTALL ELECTRIC POWER STEERING MOTOR SHAFT DAMPER

a.
C346860C01
0,0 0,0 false
V100135

Grease


Apply grease to a new electric power steering motor shaft damper.

NOTICE:

First wipe off the existing grease from the serrated part, and then apply the dedicated grease supplied with a new power steering ECU assembly or electric power steering column sub-assembly.



b.
C436908

Install the electric power steering motor shaft damper to the electric power steering column sub-assembly.


Hide 89650 2.INSTALL POWER STEERING ECU ASSEMBLY

NOTICE:
·

Do not drop the power steering ECU assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the electric power steering column sub-assembly.

·

Do not allow any moisture to come into contact with the power steering ECU assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign matter to contaminate the power steering ECU assembly.



a.
C436907

Using a T40 "TORX" socket wrench, temporarily install the power steering ECU assembly to the electric power steering column sub-assembly with the 2 bolts.

NOTICE:

When temporarily installing the 2 bolts to the power steering ECU assembly, do not tighten them all the way down.



b.
C399363

Using a 10 mm hexagon socket wrench, install the steering wheel assembly set bolt to the steering main shaft.

NOTICE:

Do not apply excessive torque to the steering wheel assembly set bolt by using a tool such as an impact wrench.


HINT:

The steering wheel assembly set bolt is used for turning the steering main shaft during inspection of the steering main shaft rotating torque.

Remove the steering wheel assembly set bolt after performing this inspection.



c.
C436909C01
0.563,1.24 1.146,1.24 true 2.344,0.948 2.688,0.948 false 1.146,1.719 0.896,1.719 0.896,1.719 0.896,1.25 true 0.896,1.479 1.156,1.479 false 0.354,1.094 0.563,1.26 0.208,0.167 10 false *a 2.74,0.865 3.052,1.021 0.313,0.156 10 false *b
*a Wooden Block
*b Cloth


Secure the steering column assembly in a vise using aluminum plates, cloths and wooden blocks.

NOTICE:
·

Do not overtighten the vise, as the steering column assembly may become deformed.

·

Secure the power steering ECU assembly so that it is upright.

·

Support the steering column assembly with wooden blocks or similar items to ensure that it does not fall.




d.
C436910

Rotate the steering main shaft 180 degrees counterclockwise and then 180 degrees clockwise at a speed of 60 rpm, and repeat 2 to 3 times to center the axis of the power steering ECU assembly. [*1]


e.

Using a T40 "TORX" socket wrench, tighten the 2 bolts. [*2]

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


f.
C436911

Using a torque wrench, measure the turning torque of the steering main shaft.

Preload:

1.0 to 2.2 N*m (11 to 22 kgf*cm, 9 to 19 in.*lbf)


NOTICE:

Ensure that there is no abnormal resistance during rotation.


If the turning torque is not as specified, loosen the 2 bolts and repeat steps [*1] and [*2] to recenter the axis of the power steering ECU assembly.


g.

Remove the steering wheel assembly set bolt.


h.

Connect the connector.


Hide 45020B 3.INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

Hide 4.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.INSTALL STEERING COLUMN ASSEMBLY

Hide 45260 6.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45260 7.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 8.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 84340 10.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 55480D 11.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 53601 12.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55317E 13.INSTALL NO. 1 INSTRUMENT SIDE PANEL

Hide 62312B 14.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 55606 15.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 67914B 17.INSTALL FRONT DOOR SCUFF PLATE LH (for 5 Door)

Hide 67914B 18.INSTALL FRONT DOOR SCUFF PLATE LH (for 3 Door)

Hide 58810J 19.INSTALL FRONT CONSOLE BOX SUB-ASSEMBLY (for 5 Door)

Hide 58810J 20.INSTALL CONSOLE BOX ASSEMBLY (for 3 Door)

Hide 21.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

Hide 45286B 22.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 23.INSTALL LOWER STEERING COLUMN COVER

Hide 24.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 25.ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 45100 26.INSTALL STEERING WHEEL ASSEMBLY

Hide 27.CHECK STEERING WHEEL CENTER POINT

Hide 45130 28.INSTALL HORN BUTTON ASSEMBLY

Hide 29.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 31. PERFORM POWER STEERING ECU INITIAL SETTING

Hide 45130 32.INSPECT HORN BUTTON ASSEMBLY

Hide 35. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART