Home › Engine / Hybrid System › FA20 ENGINE MECHANICAL › ENGINE

ENGINE > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT ENGINE COOLANT
(Click here)


2. INSPECT ENGINE OIL
(Click here)


3. INSPECT BATTERY
(Click here)


4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY



5. INSPECT SPARK PLUG
(Click here)


6. INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
  1. Remove the fan and generator V belt (Click here).

  1. Check that nothing gets caught in the tensioner by turning it clockwise and counterclockwise.
    If a any malfunction exists, replace the tensioner.

  1. Install the fan and generator V belt (Click here).



7. INSPECT IGNITION TIMING
  1. Warm up and stop the engine.

  1. When using the GTS:

    1. Connect the GTS to the DLC3.

    2. Start the engine and idle it.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

      Standard ignition timing:
      -5 to 10° BTDC at idle

      NOTICE:
      1. Switch off all the accessories and the A/C before connecting the GTS.
      2. When checking the idle speed, the transmission should be in neutral.

      HINT:
      Refer to the GTS operator's manual for further details.

    5. Check that the ignition timing advances immediately when the engine speed is increased.



  1. When not using the GTS:



      A281492
    1. Connect the tester probe of a timing light to the wire of the ignition connector for the No. 1 cylinder.

      HINT:
      Use a timing light that detects the primary current.



    2. A276027
    3. Using the timing light, check the ignition timing.

      Standard ignition timing:
      -5 to 10° BTDC at idle

      NOTICE:
      When checking the ignition timing, the transmission should be in neutral.

    4. Check that the ignition timing advances immediately when the engine speed is increased.

    5. Disconnect the timing light from the engine.



8. INSPECT ENGINE IDLE SPEED
  1. Warm up and stop the engine.

  1. When using the GTS:

    1. Connect the GTS to the DLC3.

      NOTICE:
      Switch off all the accessories and the A/C before connecting the GTS.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
      Standard Idle Speed: 
      Transmission
      Idling Speed
      for Automatic Transmission
      600 to 800 rpm
      for Manual Transmission
      550 to 750 rpm

      NOTICE:
      When checking the idle speed, the transmission should be in neutral.

      HINT:
      Refer to the GTS operator's manual for further details.

      If the idle speed is not as specified, check the air intake system.

    5. Disconnect the GTS from the DLC3.



9. INSPECT COMPRESSION
  1. Check for DTCs (Click here).

  1. Remove the relay block cover.



    A276923E01
  1. Remove the F/PMP fuse.
    Text in Illustration 
    *1
    Engine Room Relay Block

  1. Warm up and stop the engine.

  1. Remove the 4 spark plugs (Click here).



    A276029
  1. Insert a compression gauge into the spark plug hole.

  1. Install the injector driver (Click here).

  1. Inspect the cylinder compression pressure.

    1. While cranking the engine, measure the compression pressure.

      HINT:
      Always use a fully charged battery to obtain an engine speed of 250 rpm or more.

      NOTICE:
      The measurement must be performed as quickly as possible.

      Standard compression pressure:
      1750 kPa (17.8 kgf/cm2, 254 psi) or higher

      Minimum pressure:
      1150 kPa (11.7 kgf/cm2, 167 psi)

      Difference between each cylinder:
      200 kPa (2.0 kgf/cm2, 29 psi) or less

      HINT:
      If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect the compression again. Then perform the 2 steps above for the cylinders with low compression.

      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If the pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.

  1. Remove the injector driver (Click here).

  1. Install the 4 spark plugs (Click here).

  1. Reinstall the F/PMP fuse.

  1. Install the relay block cover.

  1. Clear the DTC (Click here).



10. INSPECT CO/HC

HINT:
This check is for determining whether or not the idle CO/HC complies with regulations.

  1. Start the engine.

  1. Maintain the engine speed at 2500 rpm for approximately 180 seconds.

  1. Insert a CO/HC meter testing probe at least 40 cm (1.31 ft) into the tailpipe during idling.

  1. Immediately check the CO/HC concentration at idle and/or 2500 rpm.

    HINT:
    1. When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.
    2. If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.


    1. Check the A/F sensor (Click here) and heated oxygen sensor (Click here) operation.

    2. Refer to the table below for the possible cause, and then inspect and correct the applicable causes if necessary.

      CO
      HC
      Symptom
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignition:
        1. Incorrect timing
        2. Plugs are contaminated or shorted, or plug gaps are incorrect
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinders
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. Ventilation hoses
        2. Intake manifold
        3. Throttle body
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty EFI system:
        1. Faulty pressure regulator
        2. Defective engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor