When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and the crankshaft position sensor. The VVT sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly (for port injection) ·
Fuel injector assembly (for direct injection) ·
Fuel pressure (low pressure side) ·
Fuel pressure (high pressure side) ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
| P0301 | Misfiring of the No. 1 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks). ·
An emission deterioration misfire occurs (MIL illuminates). |
|
| P0302 | Misfiring of the No. 2 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks). ·
An emission deterioration misfire occurs (MIL illuminates). |
|
| P0303 | Misfiring of the No. 3 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks). ·
An emission deterioration misfire occurs (MIL illuminates). |
|
| P0304 | Misfiring of the No. 4 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks). ·
An emission deterioration misfire occurs (MIL illuminates). |
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs once.
An excessive number of misfires (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL and stores a DTC when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected (2 trip detection logic).
At a high engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Record the DTC(s) and freeze frame data.
Clear DTCs (even if no DTCs are stored, perform the Clear DTC procedure) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSIS SYSTEM).
Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Engine Speed and Calculate Load of the Data List are the same as the freeze frame data. Perform this step several times.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
| Engine speed | Duration |
|---|---|
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and freeze frame data.
Do not turn the ignition switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.
Record the DTC(s), freeze frame data and misfire counts.
Turn the ignition switch off and wait for at least 30 seconds.
Clear DTCs (even if no DTCs are stored, perform the Clear DTC procedure) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
There was insufficient fuel in the tank.
Improper fuel was used.
The spark plugs have been contaminated.
The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count).
Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (+15% or more).
When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires have occurred only while warming up the engine.
An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections (See page Engine / Hybrid System>FA20 EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
PCV valve and hose are correctly connected and are not damaged.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Way / Port.
Start the engine and allow the engine to idle.
Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the GTS.
| Misfire Count | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | A |
| There are no misfire counts | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Way / Direct.
Start the engine and allow the engine to idle.
Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the GTS.
| Misfire Count | Proceed to | |
|---|---|---|
| Port | Direct | |
| Most misfires occur in only 1 or 2 cylinders | Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | 3 cylinders or more have equal misfire counts | B |
| Most misfires occur in only 1 or 2 cylinders | There are no misfire counts | C |
| 3 cylinders or more have equal misfire counts | There are no misfire counts | D |
A
B
C
D
Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Perform a spark test (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>FA20 (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
Check the intake system for vacuum leaks (See page Engine / Hybrid System>FA20 INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leaks from intake system.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
Same as ambient air temperature.
Between 75 and 100°C (167 and 212°F)
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine / Data List / MAF, Coolant Temp and Engine Speed.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
Between 13.0 gm/sec and 14.0 gm/sec (shift lever: N, A/C: Off).
OK
NG
Check the valve timing (See page Engine / Hybrid System>FA20 (ENGINE MECHANICAL)>TIMING CHAIN>REMOVAL).
| Result | Proceed to |
|---|---|
| ABNORMAL | A |
| NORMAL | B |
A
B
Check the fuel pressure (low pressure side) (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Inspect the fuel pump assembly (see page Engine / Hybrid System>FA20 FUEL>FUEL PUMP>INSPECTION).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Way / Direct.
Start the engine and allow the engine to idle.
Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the GTS.
| Misfire Count | Proceed to | |
|---|---|---|
| Port | Direct | |
| There are no misfire counts | There are misfire counts | A |
| There are no misfire counts | There are no misfire counts | B |
A
B
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Misfire RPM, Misfire Load, Cylinder #1 to #4 Misfire Count and Injection Way.
Monitor all of the misfire count values or DTCs and Injection Way displayed on the GTS.
| Misfire counts | Injection way | Proceed to |
|---|---|---|
| There are no misfire counts | - | A |
| Most misfires occur in only 1 or 2 cylinders | Either | B |
| 3 cylinders or more have equal misfire counts | Either | C |
| There are misfire counts | Direct | D |
A
B
C
D
Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Perform a spark test (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>FA20 (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
Check the intake system for vacuum leaks (See page Engine / Hybrid System>FA20 INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leaks from intake system.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
Same as ambient air temperature.
Between 75 and 100°C (167 and 212°F)
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine / Data List / MAF, Coolant Temp and Engine Speed.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
Between 13.0 gm/sec and 14.0 gm/sec (shift lever: N, A/C: Off).
OK
NG
Check the valve timing (See page Engine / Hybrid System>FA20 (ENGINE MECHANICAL)>TIMING CHAIN>REMOVAL).
OK
NG
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
Repair any problems.
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Warm up the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(P0300, P0301, P0302, P0303 or P0304 output) |
A |
| NORMAL
(No DTC output) |
B |
A
B
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-12 (THA) - C16-1 (THA) | Always | Below 1 Ω |
| A36-29 (E1) - C16-2 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-12 (THA) or C16-1 (THA) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C16-2 (E2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the mass air flow meter (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).
If the results of the inspections performed in steps 15 and 20 indicated no problem, proceed to the next step without replacing the mass air flow meter.
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Warm up the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(No DTC output) |
A |
| ABNORMAL
(P0300, P0301, P0302, P0303 or P0304 output) |
B |
A
B