Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM2090E _53 Suspension _060681 REAR SUSPENSION _0297610 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  REMOVAL  


PROCEDURE

Hide 1.REMOVE REAR WHEELS

Hide 89408C 2.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ HID Headlight System)

Hide 37100 3.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17430 4.REMOVE EXHAUST TAIL PIPE ASSEMBLY

Hide 41110 5.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY

Hide 42340B 6.REMOVE REAR DRIVE SHAFT ASSEMBLY LH

Hide 42330 7.REMOVE REAR DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 42305 8.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH

Hide 42304 9.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 77643A 10.REMOVE NO. 3 FUEL TANK PROTECTOR (for Metal Type)

Hide 77641A 11.REMOVE NO. 1 FUEL TANK PROTECTOR (for Clamp Type)

Hide 77642A 12.REMOVE NO. 2 FUEL TANK PROTECTOR (for Clamp Type)

Hide 46430 13.SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C260002

Remove the clamp and separate the No. 3 parking brake cable assembly.


b.
C256618

Remove the bolt and separate the No. 3 parking brake cable assembly from rear suspension member lower stopper LH.


Hide 46420 14.SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure described for the LH side.


Hide 46451B 15.REMOVE PARKING BRAKE CABLE SUPPORT BRACKET (for LH Side)

Hide 46451B 16.REMOVE PARKING BRAKE CABLE SUPPORT BRACKET (for RH Side)

HINT:

Use the same procedure described for the LH side.


Hide 48812 17.REMOVE REAR STABILIZER BAR

Hide 48720A 18.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C262315

Remove the bolt, nut and rear No. 1 suspension arm assembly LH.


Hide 48710A 19.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 20.SEPARATE REAR SHOCK ABSORBER WITH COIL SPRING LH

Hide 21.SEPARATE REAR SHOCK ABSORBER WITH COIL SPRING RH

HINT:

Use the same procedure described for the LH side.


Hide 48740F 22.SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C256611

Remove the bolt, nut and rear No. 2 suspension arm assembly LH from the rear suspension member sub-assembly.


Hide 48730F 23.SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48706B 24.REMOVE TOE CONTROL LINK SUB-ASSEMBLY LH

a.

Put matchmarks on the rear No. 2 suspension toe adjust plate and rear suspension member.

C256620E01
6.152,0.535 6.629,0.535 false 6.65,0.466 6.799,0.608 0.149,0.142 10 *a 5.522,2.679 5.998,2.679 false 6.019,2.609 6.168,2.751 0.149,0.142 10 *a

Text in Illustration
*a Matchmark - -


b.

Remove the nut, rear suspension toe adjust cam, rear No. 2 suspension toe adjust plate and toe control link sub-assembly LH.


Hide 48705 25.REMOVE TOE CONTROL LINK SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51206A 26.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C260022

Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

Text in Illustration
V100144

Attachment Placement Location

NOTICE:
·

Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.

·

Use the attachments to keep the rear suspension member sub-assembly level.




b.

Remove the 8 bolts, 2 rear lower suspension member stoppers, 2 differential support member stoppers and 2 rear suspension member lower stoppers from the rear suspension member.

C257517


c.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.



Hide 48790 27.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 28.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 41651 29.REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

Hide 41651A 30.REMOVE REAR NO. 2 DIFFERENTIAL MOUNT CUSHION