Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1202/41  Master Reservoir Level  


DESCRIPTION

When a low level of fluid in the brake master cylinder reservoir sub-assembly or an open circuit in the fluid level warning switch circuit is detected, the vehicle stability control system sends a signal to the skid control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1202/41 Master Reservoir Level
·

With ignition switch ON, communication with the main body ECU (fuse block assembly) is lost for a set period of time.

·

With ignition switch ON, brake fluid level remains low for a set period of time.


·

CAN communication system

·

Low brake fluid level

·

Brake fluid level warning switch

·

Wire harness or connector

·

Main body ECU (Fuse block assembly)

·

Skid control ECU (brake actuator assembly)


-

WIRING DIAGRAM

C356640E01
0.188,3.698 1.594,4.385 1.406,0.688 10 false Main Body ECU (Fuse Block Assembly) 0.76,4.438 2.729,4.781 1.969,0.344 10 false : Can Communication Line 2.146,3.042 4.625,3.563 2.479,0.521 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Sub-Assembly) 2.177,2.865 2.594,3.125 0.417,0.26 10 false A7 1.656,2.646 2.073,2.906 0.417,0.26 10 false 3D 1.656,1.115 2.073,1.375 0.417,0.26 10 false 3C 0.542,0.5 1.063,0.74 0.521,0.24 10 false CANH 1.656,0.5 2.073,0.76 0.417,0.26 10 false 3C 4.615,0.5 5.135,0.74 0.521,0.24 10 false CANH 0.573,1.135 1.094,1.375 0.521,0.24 10 false CANL 4.635,1.125 5.156,1.365 0.521,0.24 10 false CANL 3.198,0.542 3.719,0.781 0.521,0.24 10 false HCAN 6.219,0.5 6.74,0.74 0.521,0.24 10 false CANH 6.208,1.146 6.729,1.385 0.521,0.24 10 false CANL 3.188,1.115 3.708,1.354 0.521,0.24 10 false LCAN 1.667,0.271 2.083,0.531 0.417,0.26 10 false 21 2.708,2.521 3.125,2.781 0.417,0.26 10 false 1 1.698,2.417 2.115,2.677 0.417,0.26 10 false 3 1.656,0.906 2.073,1.167 0.417,0.26 10 false 30 2.917,0.323 3.333,0.583 0.417,0.26 10 false 25 2.906,0.938 3.323,1.198 0.417,0.26 10 false 26 3.958,1.51 4.833,1.833 0.875,0.323 10 false ECM 5.594,3.688 7.115,4.417 1.521,0.729 10 false Skid Control ECU (Brake Actuator Assembly) 2.896,2.531 3.313,2.792 0.417,0.26 10 false + 3.583,2.521 4,2.781 0.417,0.26 10 false - 3.771,2.521 4.188,2.781 0.417,0.26 10 false 2 5.594,3.51 6.01,3.771 0.417,0.26 10 false A13 5.938,2.531 6.198,2.906 0.26,0.375 10 false 25 6.219,2.656 6.74,2.896 0.521,0.24 10 false GND1 5.948,0.323 6.208,0.698 0.26,0.375 10 false 22 5.948,0.958 6.208,1.333 0.26,0.375 10 false 10 5.104,0.958 5.365,1.333 0.26,0.375 10 false 40 5.094,0.333 5.354,0.708 0.26,0.375 10 false 39 3.583,1.51 4,1.771 0.417,0.26 10 false A24 0.531,2.833 1.052,3.073 0.521,0.24 10 false BKSW

CAUTION / NOTICE / HINT

NOTICE:

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

2.CHECK BRAKE FLUID LEVEL

B

2.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is correct.

HINT:
·

If the fluid level is lower than the proper level, check for fluid leakage. If any leakage is found, repair it.

·

Check for leakage from joint sections between the brake actuator assembly, brake master cylinder reservoir sub-assembly, and wheel cylinders.

·

If no leakage is found, add brake fluid to raise it to the proper level, and then check that the DTC is not output again.



OK:

The brake fluid is at the proper level.



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

NG

BRAKE FLUID LEVEL
a.

Check for and repair brake fluid leakage. Add brake fluid to raise it to the proper level.



3.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
a.
C230719C14
1.958,1.948 2.458,2.771 false 1.521,1.948 1.021,2.771 false 2.427,2.792 2.583,2.979 0.156,0.188 10 false + 0.958,2.781 1.115,2.969 0.156,0.188 10 false - 0.198,0.198 0.51,0.354 0.313,0.156 10 false *a
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly))


Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A7 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (-) Switch OFF (Float up) 1.9 to 2.1 kΩ
1 (+) - 2 (-) Switch ON (Float down) Below 1 Ω


HINT:

If the switch condition is normal, adjust the brake fluid level to the MAX level.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Disconnect the 3D main body ECU (fuse block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-3 - A7-1 (+) Always Below 1 Ω
3D-3 or A7-1 (+) - Body ground Always 10 kΩ or higher
A7-2 (-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (BRAKE FLUID SW)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)

5.READ VALUE USING GTS (BRAKE FLUID SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical / Body / Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Fluid SW Brake level warning switch ON or OFF ON: Brake fluid switch on
OFF: Brake fluid switch off
-


d.

Disconnect the A7 connector of the brake master cylinder reservoir sub-assembly again, and then reconnect it to check the tester display.

OK:

The tester display changes in response to the connector status of connection or disconnection.



Result:
Proceed to
OK
NG



OK

6.RECONFIRM DTC

NG

6.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is not output. A
DTC is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

END

B