Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.


WIRING DIAGRAM

C356396E01
4.021,1.542 4.635,1.948 0.615,0.406 10 false ECM 3.604,1.531 3.969,1.708 0.365,0.177 10 false A24 0.542,0.49 1.156,0.896 0.615,0.406 10 false CANH 0.563,2.625 1.177,3.031 0.615,0.406 10 false CANH 3.177,2.635 3.792,3.042 0.615,0.406 10 false CANH 3.177,3.25 3.792,3.656 0.615,0.406 10 false CANL 0.563,3.24 1.177,3.646 0.615,0.406 10 false CANL 0.573,1.115 1.188,1.521 0.615,0.406 10 false CANL 3.177,0.51 3.792,0.917 0.615,0.406 10 false HCAN 3.177,1.135 3.792,1.542 0.615,0.406 10 false LCAN 6.188,0.5 6.802,0.906 0.615,0.406 10 false CANH 4.604,0.51 5.219,0.917 0.615,0.406 10 false CANH 4.625,1.125 5.24,1.531 0.615,0.406 10 false CANL 6.208,1.146 6.823,1.552 0.615,0.406 10 false CANL 6.219,4.25 6.833,4.656 0.615,0.406 10 false +IG 6.198,5.292 6.813,5.698 0.615,0.406 10 false GND1 4.875,4.427 5.49,4.833 0.615,0.406 10 false ECU-IG1 5.969,5.156 6.583,5.563 0.615,0.406 10 false 25 2.698,4.25 3.677,4.698 0.979,0.448 10 false from IG1 Relay 5.292,4.083 5.906,4.49 0.615,0.406 10 false 2 5.979,4.167 6.594,4.573 0.615,0.406 10 false 12 4.917,4.073 5.531,4.479 0.615,0.406 10 false 1 5.948,0.313 6.563,0.719 0.615,0.406 10 false 22 5.073,0.281 5.688,0.688 0.615,0.406 10 false 39 5.938,0.927 6.552,1.333 0.615,0.406 10 false 10 5.083,0.958 5.698,1.365 0.615,0.406 10 false 40 2.917,0.323 3.531,0.729 0.615,0.406 10 false 25 2.917,0.958 3.531,1.365 0.615,0.406 10 false 26 1.656,0.271 2.271,0.677 0.615,0.406 10 false 21 1.656,0.49 2.271,0.896 0.615,0.406 10 false 3C 1.667,1.115 2.281,1.521 0.615,0.406 10 false 3C 1.667,0.906 2.281,1.313 0.615,0.406 10 false 30 1.688,2.396 2.302,2.802 0.615,0.406 10 false 17 1.667,2.615 2.281,3.021 0.615,0.406 10 false 3G 1.656,3.24 2.271,3.646 0.615,0.406 10 false 3G 1.667,3.021 2.281,3.427 0.615,0.406 10 false 16 1.677,5.281 2.292,5.688 0.615,0.406 10 false 3D 1.698,5.042 2.313,5.448 0.615,0.406 10 false 3 0.521,5.458 1.135,5.865 0.615,0.406 10 false BKSW 3.281,3.625 5.229,3.906 1.948,0.281 10 false Combination Meter Assembly 2.948,3.625 3.563,4.031 0.615,0.406 10 false E34 2.021,5.479 2.635,5.885 0.615,0.406 10 false A7 2.021,5.677 4.521,6.302 2.5,0.625 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Sub-Assembly) 5.563,6.625 7.094,7.146 1.531,0.521 10 false Skid Control ECU (Brake Actuator Assembly) 5.583,6.448 6.198,6.854 0.615,0.406 10 false A13 0.208,6.604 1.583,7.167 1.375,0.563 10 false Main Body ECU (Fuse Block Assembly) 0.75,7.49 2.635,7.813 1.885,0.323 10 false : Can Communication Line 3.792,5.167 4.406,5.573 0.615,0.406 10 false 2 2.719,5.177 3.333,5.583 0.615,0.406 10 false 1 3.604,5.156 4.219,5.563 0.615,0.406 10 false - 2.906,5.156 3.521,5.563 0.615,0.406 10 false + 2.969,2.458 3.583,2.865 0.615,0.406 10 false 9 2.958,3.073 3.573,3.479 0.615,0.406 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C330019C58
1.51,0.25 1.927,0.5 0.417,0.25 2.25,0.99 2.479,0.469 true 0.927,1.365 0.865,1.854 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.594,0.292 1.99,0.583 0.396,0.292 10 false A13 0.667,1.896 1.146,2.125 0.479,0.229 10 false GND1 2.438,0.281 2.729,0.521 0.292,0.24 10 false +IG
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A13 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-12 (+IG) - Body ground Ignition switch ON 11 to 14 V
A13-12 (+IG) - A13-25 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)

5.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (BRAKE FLUID SW)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

6.READ VALUE USING GTS (BRAKE FLUID SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical / Body / Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Fluid SW Brake level warning switch ON or OFF ON: Brake fluid switch on
OFF: Brake fluid switch off
-


d.

Disconnect the A7 connector of the brake master cylinder reservoir sub-assembly again, and then reconnect it to check the tester display.

OK:

The tester display changes in response to the connector status of connection or disconnection.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (BRAKE WARNING LAMP)

NG

8.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
7.READ VALUE USING GTS (BRAKE WARNING LAMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC >Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake warning lamp Brake warning light ON or OFF ON: Warning light on
OFF: Warning light off
-


d.

Check the GTS display condition of the brake warning light.

Result:
Result Proceed to
Display of the Data List remains ON. A
Display of the Data List remains OFF. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

8.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
a.
C230719C14
1.958,1.948 2.458,2.771 false 1.521,1.948 1.021,2.771 false 2.427,2.792 2.583,2.979 0.156,0.188 10 false + 0.958,2.781 1.115,2.969 0.156,0.188 10 false - 0.198,0.198 0.51,0.354 0.313,0.156 10 false *a
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A7 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (-) Switch OFF (Float up) 1.9 to 2.1 kΩ
1 (+) - 2 (-) Switch ON (Float down) Below 1 Ω


HINT:

If the switch condition is normal, adjust the brake fluid level to the MAX level.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Disconnect the 3D main body ECU (fuse block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-3 - A7-1 (+) Always Below 1 Ω
3D-3 or A7-1 (+) - Body ground Always 10 kΩ or higher
A7-2 (-) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR