Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch (vehicle stability control switch) turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If VSC operation is turned off, the VSC OFF indicator light will come on.

WIRING DIAGRAM

C364678E01
1.531,2.313 2.323,2.792 0.792,0.479 10 false CANL 6.115,2.344 6.906,2.823 0.792,0.479 10 false CANL 6.115,1.25 6.906,1.729 0.792,0.479 10 false CANH 2.021,1.083 2.813,1.563 0.792,0.479 10 false 9 1.542,1.26 2.333,1.74 0.792,0.479 10 false CANH 2.042,2.115 2.833,2.594 0.792,0.479 10 false 8 5.865,2.135 6.656,2.615 0.792,0.479 10 false 10 5.875,1.073 6.667,1.552 0.792,0.479 10 false 22 5.865,3.229 6.656,3.708 0.792,0.479 10 false 12 6.125,3.365 6.917,3.844 0.792,0.479 10 false +IG 5.875,4.271 6.667,4.75 0.792,0.479 10 false 25 6.104,4.417 6.896,4.896 0.792,0.479 10 false GND1 1.635,4.594 2.427,5.073 0.792,0.479 10 false TCS 0.625,6.51 2.521,6.771 1.896,0.26 10 false : CAN Communication Line 0.26,6.052 2.156,6.313 1.896,0.26 10 false Combination Meter Assembly 0.281,5.875 1.073,6.354 0.792,0.479 10 false E34 5.573,5.927 7.104,6.385 1.531,0.458 10 false Skid Control ECU (Brake Actuator Assembly) 5.583,5.75 6.375,6.229 0.792,0.479 10 false A13 2.698,4.833 4.385,5.354 1.688,0.521 10 false VSC OFF Switch (Vehicle Stability Control Switch) 2.26,4.385 3.052,4.865 0.792,0.479 10 false E93 3.99,4.385 4.781,4.865 0.792,0.479 10 false E93 4.406,4.385 5.198,4.865 0.792,0.479 10 false E95 2.698,4.396 3.49,4.875 0.792,0.479 10 false E95 2.333,4.156 3.125,4.635 0.792,0.479 10 false 3 4.521,4.167 5.313,4.646 0.792,0.479 10 false 3 4.042,4.177 4.833,4.656 0.792,0.479 10 false 4 2.781,4.167 3.573,4.646 0.792,0.479 10 false 6 2.281,4.625 3.073,5.104 0.792,0.479 10 false *1 4.042,4.635 4.833,5.115 0.792,0.479 10 false *1 4.49,4.635 5.281,5.115 0.792,0.479 10 false *2 2.729,4.635 3.521,5.115 0.792,0.479 10 false *2 3.063,4.26 3.854,4.74 0.792,0.479 10 false B 3.74,4.26 4.531,4.74 0.792,0.479 10 false L 4.531,3.51 5.323,3.99 0.792,0.479 10 false ECU-IG1 4.573,3.229 5.365,3.708 0.792,0.479 10 false 1 4.979,3.229 5.771,3.708 0.792,0.479 10 false 2 2.5,3.313 3.604,3.885 1.104,0.573 10 false from IG1 Relay 2.604,6.177 3.896,6.396 1.292,0.219 10 false *1: for RHD 2.615,6.469 3.906,6.688 1.292,0.219 10 false *2: for LHD 2,4.281 2.792,4.76 0.792,0.479 10 false 17

CAUTION / NOTICE / HINT

NOTICE:

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Move the connector and wire harness of the skid control ECU (brake actuator assembly) lightly up and down and to right and left to check the status of the VSC OFF indicator light.

OK:

The status of the VSC OFF indicator light does not change.


Result:
Proceed to
OK
NG




OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ACTUATOR CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

4.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)
a.
C330019C59
1.5,0.167 1.917,0.417 0.417,0.25 2.594,0.448 2.271,0.99 true 0.719,1.865 0.906,1.365 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 1.594,0.208 2.052,0.406 0.458,0.198 10 false A13 2.635,0.344 3.094,0.542 0.458,0.198 10 false +IG 0.531,1.917 0.99,2.115 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-12 (+IG) - Body ground Ignition switch ON 11 to 14 V
A13-12 (+IG) - A13-25 (GND1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-1 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

6.READ VALUE USING GTS (VSC OFF SW AND TRC/VSC OFF MODE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (VSC OFF SW AND TRC/VSC OFF MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
VSC OFF SW VSC OFF Switch (Vehicle Stability Control Switch) ON or OFF ON: Switch on
OFF: Switch off
-
TRC/VSC Off Mode TRC/VSC Off Mode Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
Unknown: Unspecified
VSC OFF: VSC off mode
-


d.

Using the GTS, check that the switch condition displayed on the GTS changes according to VSC OFF switch operation.

OK:

The GTS display changes according to VSC OFF switch operation.



Result:
Result Proceed to
OK A
Switch input display and mode changeover display do not change. B
Switch input display or mode changeover display does not change. C



A

7.INSPECT COMBINATION METER ASSEMBLY

B

8.INSPECT VSC OFF SWITCH (VEHICLE STABILITY CONTROL SWITCH)

C

7.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform an Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
VSC TRC Indicator


c.

Check the combination meter assembly.

OK:

The TRC OFF indicator light turns on or off in accordance with the Active Test operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

8.INSPECT VSC OFF SWITCH (VEHICLE STABILITY CONTROL SWITCH)
a.

Turn the ignition switch off.


b.

Inspect the VSC OFF switch (vehicle stability control switch).

for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(for LHD)>INSPECTION

for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(for RHD)>INSPECTION

OK:

The VSC OFF switch (vehicle stability control switch) is normal.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH (VEHICLE STABILITY CONTROL SWITCH))

NG

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH (VEHICLE STABILITY CONTROL SWITCH))
a.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the E93:*1 or E95*2 VSC OFF switch (vehicle stability control switch) connector.

*1: for RHD

*2: for LHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
E34-17 (TCS) - E93-3 (B) Always Below 1 Ω
E34-17 (TCS) or E93-3 (B) - Body ground Always 10 kΩ or higher
E93-4 (L) - Body ground Always Below 1 Ω


Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
E34-17 (TCS) - E95-6 (B) Always Below 1 Ω
E34-17 (TCS) or E95-6 (B) - Body ground Always 10 kΩ or higher
E93-3 (L) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Select the Data List using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC OFF SW TRC OFF Switch OFF or ON OFF: TRC OFF switch released
ON: TRC OFF Switch pushed
-

OK:

The VSC OFF switch (vehicle stability control switch) operates normally.



c.

Perform an Active Test of the combination meter assembly using the GTS.

OK:

The TRC OFF indicator light turns on or off in accordance with the Active Test operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY