Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › 2019.09–2020.08
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0292475 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: If the vehicle height has changed due to suspension or tire replacement

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration
·

Lane departure alert system (w/ Steering Control)

·

Toyota parking assist-sensor system*1

·

Parking support brake system*1

·

Simple intelligent parking assist system*1

·

Pre-collision system


(Click here)
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of continuously variable transaxle assembly Perform the following procedures in the order shown:
1.

Reset memory

2.

Deceleration sensor zero point calibration

3.

CVT oil pressure calibration


Deterioration of fuel efficiency (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.*2 Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.REMOVE FRONT WHEELS

Hide 51441 5.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51443C 6.REMOVE REAR ENGINE UNDER COVER RH

Hide 51444A 7.REMOVE REAR ENGINE UNDER COVER LH

Hide 11.DRAIN COOLANT (for Intercooler)

Hide 13.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55737B 14.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 15.REMOVE WATER GUARD PLATE LH (for TMC Made RHD)

Hide 55736D 16.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 17.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 18.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 19.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 28800 20.REMOVE BATTERY

Hide 53141F 21.REMOVE RADIATOR COVER

Hide 17751 22.REMOVE NO. 1 AIR CLEANER INLET

Hide 23.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 24.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 26.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A390461

Remove the bolt and nut to separate the engine wire from the battery clamp sub-assembly.


b.
A392287

Disengage the clamp to separate the engine wire from the battery clamp sub-assembly.


c.

Remove the 3 bolts and battery clamp sub-assembly from the vehicle.


Hide 33820B 27.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 82121 28.DISCONNECT ENGINE WIRE

a.

Disconnect the transmission wire connector.

C364040C03
2.25,0.854 2.5,1.083 0.25,0.229 10 true *1 2,1.667 2.25,1.896 0.25,0.229 10 true *2 2.25,2.333 2.5,2.563 0.25,0.229 10 true *3 4.417,0.521 4.667,0.75 0.25,0.229 10 true *4 4.833,2.188 5.083,2.417 0.25,0.229 10 true *5
*1 Park/Neutral Position Switch Connector *2 Transmission Wire Connector
*3 Transmission Revolution Sensor (NIN) Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 Oil Pressure Sensor Connector - -



b.

Disconnect the transmission revolution sensor (NIN) connector.


c.

Disconnect the park/neutral position switch connector.


d.

Disconnect the transmission revolution sensor (NOUT) connector.


e.

Disconnect the oil pressure sensor connector.


f.

Disengage the 7 clamps to disconnect the engine wire from the continuously variable transaxle assembly.


g.

Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.


Hide 29.DISCONNECT WATER HOSE

a.
C364042

Slide the 2 hose clips and disconnect the water hoses from the transmission oil cooler.


b.

Disengage the 2 clamps to separate the water hose from the continuously variable transaxle assembly.


Hide 33823 30.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C327723

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 45100 31.SECURE STEERING WHEEL ASSEMBLY

Hide 45259A 32.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 33.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 34.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 57533B 35.REMOVE FRONT FLOOR CENTER BRACE

Hide 17420K 36.REMOVE NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 17410 37.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 38.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 39.REMOVE FRONT DRIVE SHAFT ASSEMBLIES (for TMC Made)

Hide 40.REMOVE FRONT DRIVE SHAFT ASSEMBLIES (for TMMT Made)

Hide 41.INSTALL ENGINE HANGERS

a.
A392293

Disengage the 3 clamps from the wire harness clamp bracket.


b.

Remove the nut to separate the engine wire from the wire harness clamp bracket.


c.

Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.


d.
C364032

Separate the bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH.


e.
A351514C04
0.406,1.604 0.75,1.604 true 2.531,1.073 2.875,1.073 true 0.219,1.542 0.531,1.698 0.313,0.156 10 false *1 2.958,1.01 3.271,1.167 0.313,0.156 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
V100135

Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-47060
No. 2 Engine Hanger 12282-47030
Bolt 91552-81030



Hide 42.INSTALL ENGINE SUPPORT BRIDGE

a.
C364030

Remove the clip and the neck from the windshield washer jar assembly.


b.

Install SST to the vehicle body as shown in the illustration.

C365148C01
5.875,3.156 6.313,2.979 false 4.427,6.156 5.094,6.156 true 1.99,6.073 2.333,6.25 true 4.417,5 5.323,5.333 true 1.781,5.24 2.667,5.083 true 1.25,1.333 1.833,1.042 true 5.333,1.417 4.896,1.115 true 4.198,4.865 4.417,5.063 0.219,0.198 10 true *a 4.188,6.063 4.417,6.25 0.229,0.188 10 true *b 5.344,1.333 5.563,1.531 0.219,0.198 10 true *c 6.354,2.875 6.698,3.042 0.344,0.167 10 false SST 2.354,6.177 2.583,6.365 0.229,0.188 10 true *b 2.688,4.969 2.906,5.167 0.219,0.198 10 true *a 1.031,1.26 1.25,1.458 0.219,0.198 10 true *c
*a Support Shaft *b Front Side Member
*c Front Suspension Nut - -


SST
09940-10020  

CAUTION:
·
C330755C01
0.448,1.167 0.781,1.167 false 2.438,1.167 2.771,1.167 false 1.052,1.781 1.052,1.448 1.052,1.448 1.219,1.448 false 2.604,1.781 2.604,1.448 2.604,1.448 2.438,1.448 false 0.292,1.094 0.604,1.25 0.313,0.156 10 false *a 2.271,1.094 2.583,1.25 0.313,0.156 10 false *a 1.281,1.385 1.594,1.542 0.313,0.156 10 false *b 2.271,1.385 2.583,1.542 0.313,0.156 10 false *b
*a Support Shaft
*b Front Side Member


Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.

·

The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.



NOTICE:
·

Prevent SST from contacting the vehicle body exterior and windshield glass.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed before performing work.




c.
C338947C01
0.615,1.479 0.615,0.656 0.615,0.656 0.5,0.656 false 1.042,2.125 1.667,2.125 false 1.031,2.469 2.167,2.469 false 0.875,2.771 0.875,2.458 0.875,2.458 0.76,2.458 false 1.708,2.01 2.063,2.281 0.354,0.271 10 false *a 0.292,0.552 0.604,0.823 0.313,0.271 10 false *b 0.552,2.354 0.917,2.583 0.365,0.229 10 false *c 2.208,2.375 2.563,2.667 0.354,0.292 10 false *d
*a Support Shaft
*b Sub Beam
*c Front Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.


d.

Install the chain block to the sling bracket.

C365149C01
1.583,1 1.917,1 false 0.313,0.604 1.313,0.604 true 0.802,1.573 1.302,1.573 true 0.833,1.167 1.292,1.469 false 1.948,0.896 2.125,1.083 0.177,0.188 10 false *a 0.125,0.5 0.302,0.677 0.177,0.177 10 true *b 0.646,1.01 0.833,1.198 0.188,0.188 10 true *c 0.615,1.469 0.792,1.646 0.177,0.177 10 true *d
*a Chain Block *b Sling Bracket
*c Fuse Shackle *d Shackle (A)



e.

Install the division bar to the chain block with the shackles.

CAUTION:
·
C338949C01
0.458,2.313 0.583,2.313 0.583,2.313 0.875,2.635 false 0.354,2.677 0.479,2.677 0.479,2.677 0.865,2.865 false 2.177,2.271 2.302,2.271 2.302,2.271 2.604,2.594 false 2.073,2.656 2.198,2.656 2.198,2.656 2.583,2.844 false 0.281,2.208 0.604,2.469 0.323,0.26 10 false *a 0.167,2.573 0.51,2.844 0.344,0.271 10 false *b 1.99,2.156 2.313,2.417 0.323,0.26 10 false *a 1.885,2.542 2.229,2.813 0.344,0.271 10 false *b
*a Fuse Shackle
*b Shackle (A)


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·

If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with automatic transaxle assembly may fall.

·
C330757C01
2.75,1 3.083,1 false 1.01,1 1.344,1 false 0.917,1.417 1.333,1.583 true 2.635,1.396 3.083,1.583 true 1.396,0.917 1.708,1.073 0.313,0.156 10 false *a 1.385,1.51 1.698,1.667 0.313,0.156 10 false *b 3.125,0.917 3.354,1.083 0.229,0.167 10 false *a 3.135,1.5 3.354,1.667 0.219,0.167 10 false *b
*a Fuse Shackle
*b Fuse Bolt


Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.

·

If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.




f.

Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.

C365150C01
2.25,4.042 2.25,3.542 true 1.667,4 1.26,3.75 true 1.052,3.927 0.583,3.75 true 0.875,4.458 0.458,4.458 true 1.75,1 1.302,1.271 true 0.5,1.708 0.5,1.292 true 1.323,1.49 1,1.583 true 2.198,1.604 1.74,1.76 true 0.219,4.354 0.406,4.531 0.188,0.177 10 true *1 2.25,1.531 2.438,1.719 0.188,0.188 10 true *2 2.156,4.052 2.365,4.24 0.208,0.188 10 true *a 1.688,3.917 1.885,4.115 0.198,0.198 10 true *b 0.375,3.615 0.573,3.802 0.198,0.188 10 true *c 0,0.781 0.156,0.938 0.156,0.156 10 false - 1.76,0.885 1.958,1.083 0.198,0.198 10 true *b 0.802,1.5 1,1.688 0.198,0.188 10 true *c 0.406,1.708 0.615,1.896 0.208,0.188 10 true *a
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Chain - -


NOTICE:

Connect the 2nd link of the chain to the No. 1 engine hanger.



g.

Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 2nd link of the chain to the No. 2 engine hanger.



h.
C330764C02
1.219,0.792 1.531,0.948 0.313,0.156 10 false *a
*a 120 mm (4.72 in.) or more


Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.

HINT:

If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.



i.

Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.

C365151C01
3.5,1.5 4,1.5 true 4.25,0.958 4.75,0.583 false 4.01,1.396 4.229,1.594 0.219,0.198 10 true *a 4.76,0.438 5.073,0.594 0.313,0.156 10 false *b 6.115,0.427 6.427,0.583 0.313,0.156 10 false *c 1,0.406 1.313,0.563 0.313,0.156 10 false *d 3.198,0.344 3.51,0.5 0.313,0.156 10 false *e 0.979,2.333 1.146,2.5 0.167,0.167 10 true *f 6.135,2.365 6.302,2.531 0.167,0.167 10 true *f
*a Chain Block *b Main Beam
*c Dimension (A) *d Dimension (B)
*e Right to Left Adjustment *f Front to Rear Adjustment


CAUTION:
·

To prevent the engine with automatic transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.

·
C365152C01
2.01,1.49 2.302,1.125 false 2.271,0.948 2.583,1.104 0.313,0.156 10 false *a
*a Main Beam


Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.

·

Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with automatic transaxle assembly and engine support bridge to fall, possibly causing serious injury.




j.

Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.

C365154C01
2.469,1.052 2.667,1.229 0.198,0.177 10 true *a 1.281,1.708 1.479,1.885 0.198,0.177 10 true *b 1.76,1.021 1.958,1.198 0.198,0.177 10 true *a 2.063,0.042 2.26,0.219 0.198,0.177 10 false *a 4.844,0.042 5.042,0.219 0.198,0.177 10 false *a 4.396,1.031 4.594,1.208 0.198,0.177 10 true *a 5.104,1.042 5.302,1.219 0.198,0.177 10 true *a 5.552,1.604 5.75,1.781 0.198,0.177 10 true *b
*a Wing Bolt *b Bolt


Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)

CAUTION:
·
C330761

Do not perform any procedures before tightening the bolts to the specified torque.

·

Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.




k.
C365155C01
2.656,3.125 2.854,3.333 0.198,0.208 10 true *a
*a Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C330770C01
2.99,2.292 3.302,2.448 0.313,0.156 10 false *a
*a 41 N*m (418 kgf*cm, 30 ft.*lbf) or more


·

When suspending the engine with automatic transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.




Hide 51108A 43.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 44.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

Hide 51201 45.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 12364B 46.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C364047

Remove the 4 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.


Hide 30400 47.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C366435C01
1.792,0.917 1.344,0.865 true 1.156,0.76 1.333,0.938 0.177,0.177 10 true *a
*a Lashing Belt


Using a transmission jack, support the continuously variable transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.

·

To prevent the transaxle oil (CVT) pan sub-assembly from deforming, do not place any attachments under the transaxle oil (CVT) pan sub-assembly of the continuously variable transaxle assembly.

·

Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.




Hide 28100 48.REMOVE STARTER ASSEMBLY (for Valeo Made Cold Area Specification Vehicles)

Hide 28100 49.REMOVE STARTER ASSEMBLY (for Valeo Made except Cold Area Specification Vehicles)

Hide 28100 50.REMOVE STARTER ASSEMBLY (for Denso Made without Stop and Start System)

Hide 11363A 51.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 11361J 52.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A351509

Remove the flywheel housing under cover from the stiffening crankcase assembly.


Hide 32101G 53.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C327719

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 12372A 54.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

a.
C364043

Remove the bolt and nut to separate the transverse engine engine mounting insulator from the engine mounting bracket LH.


b.
C364044

Remove the nut and 4 bolts.


c.

Remove the transverse engine engine mounting insulator from the vehicle body.


Hide 55.REMOVE ENGINE MOUNTING STAY LH

a.
C364045

Remove the 2 bolts and engine mounting stay LH from the continuously variable transaxle assembly.


Hide 12325A 56.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C364046

Remove the 3 bolts and transverse engine engine mounting bracket from the continuously variable transaxle assembly.


Hide 30400 57.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C327721N01
0.885,0.063 1.042,0.26 0.156,0.198 10 true A 2.406,0.052 2.563,0.25 0.156,0.198 10 true A 0.552,0.854 0.708,1.052 0.156,0.198 10 true B 0.844,1.74 1,1.938 0.156,0.198 10 true B 1.365,1.979 1.521,2.177 0.156,0.198 10 true B 2.135,1.979 2.292,2.177 0.156,0.198 10 true B 2.583,1.917 2.74,2.115 0.156,0.198 10 true B

Remove the 7 bolts and continuously variable transaxle assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.


HINT:
·

Bolt (A): Remove from continuously variable transaxle assembly side.

·

Bolt (B): Remove from engine assembly side.




Hide 32000A 58.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C327722

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 30400E 59.REMOVE CVT OIL PUMP TYPE T OIL SEAL

NOTICE:
·

Do not remove the front oil pump assembly from the CVT main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.

·

Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.



a.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


b.
C329642N01
1.552,2.635 1.552,2.24 false 1.448,2.677 1.906,2.875 0.458,0.198 10 false SST

Using SST, remove the CVT oil pump type T oil seal.

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.



Hide 36100A 61.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

Hide 62.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C364048

Remove the 4 bolts and 4 wire harness clamp brackets from the continuously variable transaxle assembly.


Hide 87101A 63.REMOVE NO. 1 HEATER BRACKET SUB-ASSEMBLY

a.
C327727

Separate the No. 1 breather plug (CVT) from the clamp.


b.
C327728

Remove the clamp from the No. 1 heater bracket sub-assembly.


c.
C327729

Remove the bolt and No. 1 heater bracket sub-assembly from the continuously variable transaxle assembly.


Hide 64.REMOVE STRAIGHT SCREW PLUG

HINT:

Perform this procedure only when replacement of the straight screw plug is necessary.


a.
C333413

Remove the straight screw plug and gasket from the continuously variable transaxle assembly.


Hide 35012B 65.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the transmission breather hose sub-assembly is necessary.


a.
C333414

Remove the transmission breather hose sub-assembly from the continuously variable transaxle assembly.


b.
C333415C01
0.823,0.969 0.823,0.635 false 2.615,1.115 2.948,1.115 false 1.688,1.51 1.688,1.177 false 2.646,1.667 2.979,1.667 false 0.76,0.99 1.073,1.146 0.313,0.156 10 false *1 1.635,1.542 1.948,1.698 0.313,0.156 10 false *2 3,1.052 3.313,1.208 0.313,0.156 10 false *3 3.021,1.604 3.333,1.76 0.313,0.156 10 false *4
*1 No. 1 Breather Plug (CVT)
*2 Breather Plug Hose
*3 No. 2 Breather Plug (CVT)
*4 O-ring


Remove the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) from the breather plug hose.


c.

Remove the O-ring from the No. 2 breather plug (CVT).


Hide 32000A 66.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 67.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY