Home › Engine / Hybrid System › 3ZR-FAE (FUEL) › FUEL INJECTOR › from 2020.08
RM32H0E _51 Engine / Hybrid System _060184 3ZR-FAE FUEL _0295033 FUEL INJECTOR A

3ZR-FAE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Apply a light coat of gasoline or spindle oil to new O-rings, and then install one onto each fuel injector assembly.


b.

Apply a light coat of gasoline or spindle oil where the fuel delivery pipe sub-assembly contacts each O-ring.


c.
A153013

While turning the fuel injector assembly left and right, install it onto the fuel delivery pipe sub-assembly.

NOTICE:
·

Do not damage the fuel injector assembly and O-ring.

·

Do not twist the O-ring.

·

After installing each fuel injector assembly, check that it turns smoothly. If not, replace the O-ring with a new one.



HINT:

Use the same procedure to install the other fuel injector assemblies.



Hide 23291 2.INSTALL INJECTOR VIBRATION INSULATOR

a.

Install 4 new injector vibration insulators to the cylinder head sub-assembly.


Hide 23807V 3.INSTALL NO. 1 DELIVERY PIPE SPACER

a.
A153008C02
1.625,0.198 1.917,0.406 0.292,0.208 10 false *a 1.635,0.698 1.896,0.875 0.26,0.177 10 false *b
*a Fuel Delivery Pipe Sub-assembly Side
*b Cylinder Head Sub-assembly Side


Install the 2 No. 1 delivery pipe spacers onto the cylinder head sub-assembly.

NOTICE:

Install the No. 1 delivery pipe spacers in the correct direction.



Hide 23807 4.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

Do not drop the fuel injector assemblies when installing the fuel delivery pipe sub-assembly.

·

After installing the fuel delivery pipe sub-assembly, check that the fuel injector assemblies turn smoothly.




b.

Install the clamp to the cylinder head sub-assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 89421 6.INSTALL VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 23901 7.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
A149876C12
2.135,3.208 1.656,2.656 1.656,2.656 1.5,2.656 true 1.146,4.125 1.552,4.125 1.552,4.125 1.552,3.771 true 0.531,4.063 0.531,3.792 false 2.188,4.219 2.188,3.979 false 2.896,3.969 2.896,3.729 false 1.354,4.125 1.354,3.781 true 1.323,2.563 1.635,2.719 0.313,0.156 10 false *a 0.448,4.104 0.76,4.26 0.313,0.156 10 false *e 0.979,4.052 1.292,4.208 0.313,0.156 10 false *b 2.802,3.99 3.115,4.146 0.313,0.156 10 false *d 2.125,4.25 2.438,4.406 0.313,0.156 10 false *c
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
*e Nylon Tube


Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly.

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


i.

Align the fuel tube connector with the fuel pipe, and push the fuel pipe into the fuel tube connector until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.



b.

Engage the 2 claws to install a new No. 2 fuel pipe clamp.


Hide 8.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the camshaft housing sub-assembly with the 2 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 74404A 10.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 82121 11.CONNECT ENGINE WIRE

a.

Connect the engine wire to the battery clamp sub-assembly with the bolt and nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 28800 12.INSTALL BATTERY

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 15. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the battery, there is an automatic leaning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 18.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION