Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P2A0026    O2 Sensor Circuit Range/Performance Bank 1 Sensor 1 Signal Rate of Change Below Threshold

for Preparation Click here


DESCRIPTION

Refer to DTC P21951D .

HINT:
Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.


DTC No.
DTC Detection Condition
Trouble Area
P2A0026
The calculated value for the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic).
  1. Air fuel ratio sensor (sensor 1)
  2. Intake system
  3. Fuel injector assembly (for port injection)
  4. Fuel injector assembly (for direct injection)
  5. Fuel pressure (for low pressure side)
  6. Fuel pressure (for high pressure side)
  7. Fuel system
  8. EGR valve assembly
  9. ECM

MONITOR DESCRIPTION

After the engine is warmed up, the ECM performs air fuel ratio feedback control to maintain the air fuel ratio at the stoichiometric level. In addition, active air fuel ratio control is performed for approximately 30 seconds after preconditions are met in order to measure the air fuel ratio sensor response rate. During active air fuel ratio control, the ECM forcibly increases and decreases the injection volume by a certain amount, based on the stoichiometric air fuel ratio learned during normal air fuel ratio control, and measures the air fuel ratio sensor response rate. The ECM receives a signal from the air fuel ratio sensor while performing active air fuel ratio control and uses it to calculate the air fuel ratio sensor response rate deterioration level.
If the value for the air fuel ratio sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and stores the DTC.

A115363E58


MONITOR STRATEGY


Required Sensors/Components
Air fuel ratio sensor
Frequency of Operation
Once per driving cycle

TYPICAL ENABLING CONDITIONS


Active air fuel ratio control
Performing
Active air fuel ratio control performed when following conditions met
-
Engine coolant temperature
75°C (167°F) or higher
Idling
Off
Engine speed
Less than 4000 rpm
Air fuel ratio sensor status
Activated
Engine load
10% or higher, and less than 70%
Catalyst monitor
Not yet
Mass air flow
2.6 gm/sec or more, and less than 13.4 gm/sec

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


A295461E03

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG).
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the engine switch off and wait for at least 30 seconds.
  6. Turn the engine switch on (IG) and turn the GTS on.
  7. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  8. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more in a city area [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  12. Input the DTC: P2A0026.
  13. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A and no pending DTC is output, perform the following procedure.

  14. Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  15. Enter the following menus: Powertrain / Engine / Trouble Codes [E].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  18. Input the DTC: P2A0026.
  19. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, drive the vehicle again under an increased load and then recheck the judgment result.


WIRING DIAGRAM

Refer to DTC P21951D .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:
  1. DTC P2A0026 may be also stored when the air fuel ratio is stuck at rich or lean.
  2. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.
  6. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A0026)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P2A0026 is output
    A
    DTC P2A0026 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.

  1. Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    GTS Display (Sensor)
    Injection Volume
    Status
    Voltage
    A/F (O2) Sensor Voltage B1S1
    (Air fuel ratio)
    12.5%
    Rich
    Below 3.1 V
    -12.5%
    Lean
    Higher than 3.4 V
    O2 Sensor Voltage B1S2
    (Heated oxygen)
    12.5%
    Rich
    Higher than 0.55 V
    -12.5%
    Lean
    Below 0.4 V

    Result:

    Status of A/F (O2) Sensor Voltage B1S1
    Status of O2 Sensor Voltage B1S2
    Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    A
    Lean
    Lean
    Actual air fuel ratio lean
    B
    Rich
    Rich
    Actual air fuel ratio rich
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    C
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction

    1. Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (A/F (O2) Sensor Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2) is consistently below 0.4 V.
    2. Rich: During Control the Injection Volume for A/F Sensor, the A/F (O2) Sensor Voltage B1S1 is consistently below 3.1 V, and the O2 Sensor Voltage B1S2 is consistently higher than 0.55 V.
    3. Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternates correctly.

    HINT:
    Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2] (Click here).



B
Go to step 4

C
Go to step 11
A


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A0026)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P2A0026.

  1. Check the DTC judgment result.

    Result:

    Result
    Proceed to
    NORMAL
    (DTCs are not output)
    A
    ABNORMAL
    (DTC P2A0026 is output)
    B



B
Go to step 11
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


5.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in the intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


6.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
  1. Check the fuel pressure (for low pressure side) .



NG
Go to step 10
OK


7.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Inspect the fuel injector assembly (for port injection) (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (for port injection) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
OK


8.READ VALUE USING GTS (FUEL PRESSURE (HIGH))
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Fuel Pressure (High).

  1. Read the values.

    Standard:
    2750 to 8000 kPag (3000 rpm, engine warmed up, shift lever in P, A/C off).



NG
REPAIR OR REPLACE FUEL SYSTEM (FOR HIGH PRESSURE SIDE)
OK


9.INSPECT FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)
  1. Inspect the fuel injector assembly (for direct injection) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection) (Click here).



OK
Go to step 11

NG
REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION) (Click here)

10.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
  1. Inspect the fuel pump (for low pressure side) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side) (Click here).



NG
REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE) (Click here)
OK

REPAIR OR REPLACE FUEL LINE (LOW PRESSURE SIDE) 

11.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).


NEXT


12.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A0026)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P2A0026.

  1. Check the DTC judgment result.

    Result:

    Result
    Proceed to
    ABNORMAL
    (DTC P2A0026 is output)
    A
    NORMAL
    (DTCs are not output)
    B



B
END
A


13.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / All Data / Engine Speed and Intake Manifold Absolute Pressure.

  1. Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

    NOTICE:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling or engine stalls
    Intake Manifold Absolute Pressure
    (Data List)
    Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs)
    (150 to 300 mmHg(abs))
    (EGR valve is fully closed)
    Intake Manifold Absolute Pressure value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



OK
Go to step 15

NG
Go to step 14

14.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


15.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


16.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A0026)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P2A0026.

  1. Check that the DTC judgment result is NORMAL.


NEXT

END