Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM J

N04C-UH ENGINE CONTROL  ECD SYSTEM  Engine Difficult to Start or Stalling  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.

·

If the vehicle runs out of fuel while the engine is operating, there is a chance that the engine may be difficult to restart after fuel is refilled.



PROCEDURE

1.CHECK DTC OUTPUT (RELATED TO ENGINE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.


Result:
Result Proceed to
No output A
DTCs related to engine B



A

2.CHECK FUEL FILTER ASSEMBLY

B

2.CHECK FUEL FILTER ASSEMBLY
a.

Check that the fuel filter is not clogged.

OK:

Fuel filter is not clogged.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE CRANKING CONDITION

NG

REPLACE FUEL FILTER ASSEMBLY

3.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.


b.

Compare the cranking condition with that of a normal engine of the same model, and carefully check if there is any difference between them.

OK:

Engine cranking condition is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

NG

CHECK AND REPLACE BATTERY, CHARGING SYSTEM, STARTER ASSEMBLY AND STARTING SYSTEM

4.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Read the value.

Standard:
Item Inspection Condition Reference Value
Fuel Press Cranking, and engine coolant temperature 0°C (32°F) or more 15000 kPa or more



Result:
Proceed to
OK
NG



OK

5.CHECK IF INITIAL COMBUSTION OCCURS

NG

BLEED AIR FROM FUEL SYSTEM

5.CHECK IF INITIAL COMBUSTION OCCURS
a.

Check if initial combustion occurs.


Result:
Result Proceed to
No initial combustion A
Initial combustion occurs B



A

6.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

B

7.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
6.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Check that the internal fuel pressure of the common rail is within the specification below.

Standard:
Engine Speed Engine Speed
Idling Approximately 25000 to 35000 kPa



Result:
Proceed to
OK
NG



OK

7.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

NG

13.CHECK IF FUEL IS BEING SUPPLIED TO INJECTION OR SUPPLY PUMP ASSEMBLY
7.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

Result:
Proceed to
OK
NG



OK

8.INSPECT EXHAUST RETARDER ASSEMBLY

NG

REPAIR OR REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

8.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

9.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND INJECTION VOLUME)

NG

REPLACE EXHAUST RETARDER ASSEMBLY

9.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND INJECTION VOLUME)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

Fuel Press

·

Injection Volume


Standard:
Item Engine Speed* Reference Value
Fuel Press Idling 25000 to 35000 kPa
Injection Volume Idling 5 to 16 mm3/st


HINT:

*: The shift lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.



Result:
Proceed to
OK
NG



OK

10.CHECK CYLINDER COMPRESSION PRESSURE

NG

14.INSPECT ECM (THW TERMINAL VOLTAGE)
10.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click here Engine / Hybrid System>N04C-UH (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

11.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)
a.

Check the wire harness between the injector assembly and injector driver assembly (INJ terminal).

i.

Disconnect the injector assembly connectors.


ii.

Disconnect the injector driver assembly connectors.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 - B98-5 (INJ1) Always Below 1 Ω
i2-2 - B96-4 (INJ2) Always Below 1 Ω
i3-2 - B96-2 (INJ3) Always Below 1 Ω
i4-2 - B98-4 (INJ4) Always Below 1 Ω
i1-1 - B98-1 (COM1) Always Below 1 Ω
i2-1 - B98-2 (COM2) Always Below 1 Ω
i3-1 - B98-2 (COM2) Always Below 1 Ω
i4-1 - B98-1 (COM1) Always Below 1 Ω
i1-2 or B98-5 (INJ1) - Body ground Always 10 kΩ or higher
i2-2 or B96-4 (INJ2) - Body ground Always 10 kΩ or higher
i3-2 or B96-2 (INJ3) - Body ground Always 10 kΩ or higher
i4-2 or B98-4 (INJ4) - Body ground Always 10 kΩ or higher
i1-1 or B98-1 (COM1) - Body ground Always 10 kΩ or higher
i2-1 or B98-2 (COM2) - Body ground Always 10 kΩ or higher
i3-1 or B98-2 (COM2) - Body ground Always 10 kΩ or higher
i4-1 or B98-1 (COM1) - Body ground Always 10 kΩ or higher



iv.

Reconnect the injector assembly connectors.


v.

Reconnect the injector driver assembly connectors.



Result:
Proceed to
OK
NG



OK

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Result Proceed to
Engine idling condition becomes unstable A
Engine idling condition does not change B



A

REPLACE INJECTOR DRIVER ASSEMBLY

B

13.CHECK IF FUEL IS BEING SUPPLIED TO INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the injection or supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the injection or supply pump assembly.

OK:

Fuel is properly supplied to the injection or supply pump assembly when the priming pump is operated.



Result:
Proceed to
OK
NG



OK

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

NG

CHECK AND REPLACE FUEL PIPE CLOGGING (INCLUDING FUEL FREEZING) (FUEL TANK - SUPPLY PUMP)

14.INSPECT ECM (THW TERMINAL VOLTAGE)
a.
A224395E33
0.51,0.198 0.938,0.448 0.427,0.25 0.531,1.531 0.948,0.938 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.229,1.563 0.927,1.771 0.698,0.208 10 false 19 (THW) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B59-19 (THW) - B59-28 (E2) Idling, engine coolant temperature between 80 and 120°C (176 and 248°F) 0.2 to 1.0 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

15.INSPECT CRANKSHAFT POSITION SENSOR

NG

18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
15.INSPECT CRANKSHAFT POSITION SENSOR
a.

While idling the engine, check the waveform between the specified terminals of the ECM connector using an oscilloscope.

A427627E04
0.885,0.729 1.281,0.979 0.396,0.25 1.417,0.729 1.813,0.979 0.396,0.25 0.646,1.969 0.854,1.396 true 1.427,2.063 0.854,1.448 true 2.135,2.063 1.698,1.448 true 2.135,0.927 1.698,1.396 true 0.219,0.24 0.531,0.438 0.313,0.198 10 false *1 0.958,0.781 1.271,0.979 0.313,0.198 10 false B59 1.5,0.771 1.813,0.969 0.313,0.198 10 false B60 0.354,2 0.979,2.198 0.625,0.198 10 false 27 (NE+) 1.208,2.094 1.833,2.292 0.625,0.198 10 false 34 (NE-) 2.01,2.104 2.635,2.302 0.625,0.198 10 false 31 (G-) 2.188,0.781 2.813,0.979 0.625,0.198 10 false 23 (G+) 4.083,0.25 4.396,0.448 0.313,0.198 10 false *2 4.125,0.896 4.375,1.083 0.25,0.188 10 false G+ 4.115,1.51 4.365,1.698 0.25,0.188 10 false NE 6.063,0.708 7.156,0.885 1.094,0.177 10 false 5 V/DIV. 4.833,2.135 6.688,2.479 1.854,0.344 10 false 20 msec./DIV.

Text in Illustration
*1 Component with harness connected
(ECM)
*2 G+ and NE Signal Waveforms

Standard:
Tester Connection Condition Specified Condition
B59-27 (NE+) - B59-34 (NE-) Engine idling Correct waveform appears as shown
B60-23 (G+) - B60-31 (G-) Engine idling Correct waveform appears as shown



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (STARTER RELAY - ECM)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR
16.CHECK HARNESS AND CONNECTOR (STARTER RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the starter relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - B60-18 (STA) Always Below 1 Ω
ST relay terminal 1 or B60-18 (STA) - Body ground Always 10 kΩ or higher



d.

Reinstall the starter relay.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

17.INSPECT ECM (PCR1 TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT ECM (PCR1 TERMINAL VOLTAGE)
a.
A224395E25
0.51,0.198 0.938,0.448 0.427,0.25 0.323,1.531 0.563,0.958 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.094,1.573 0.833,1.792 0.74,0.219 10 false 26 (PCR1) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B59-26 (PCR1) - B59-28 (E2) Idling 1.3 to 1.7 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

20.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.
A126612E10
0.729,0.245 0.949,0.388 0.22,0.143 10 *1 0.635,1.687 0.811,1.828 0.177,0.142 10 30 0.635,1.877 0.811,2.019 0.177,0.142 10 20 0.635,2.176 0.811,2.318 0.177,0.142 10 10 0.732,2.49 0.83,2.632 0.098,0.142 10 5 0.732,3.145 0.83,3.287 0.098,0.142 10 1 2.419,2.95 2.603,3.121 0.184,0.171 10 *2 1.194,3.375 1.388,3.547 0.193,0.171 10 *3 0.732,2.904 0.83,3.046 0.098,0.142 10 2 0.732,2.709 0.83,2.851 0.098,0.142 10 3 0.587,3.602 0.802,3.743 0.216,0.142 10 0.3 0.587,3.416 0.802,3.558 0.216,0.142 10 0.5 0.587,3.952 0.802,4.094 0.216,0.142 10 0.1 0.587,3.761 0.802,3.903 0.216,0.142 10 0.2 0.89,4.019 1.108,4.165 0.218,0.146 10 -20 1.279,4.019 1.374,4.171 0.095,0.152 10 0 1.542,4.019 1.716,4.165 0.174,0.146 10 20 1.884,4.019 2.058,4.17 0.174,0.151 10 40 2.223,4.019 2.399,4.168 0.176,0.149 10 80 2.594,4.019 2.893,4.161 0.299,0.142 10 100 0.879,4.192 1.115,4.366 0.236,0.174 10 (-4) 1.17,4.192 1.441,4.366 0.271,0.174 10 (32) 1.482,4.192 1.753,4.366 0.271,0.174 10 (68) 1.786,4.192 2.133,4.366 0.347,0.174 10 (104) 2.185,4.192 2.533,4.366 0.347,0.174 10 (176) 2.594,4.192 2.941,4.366 0.347,0.174 10 (212) 0.878,1.575 1.081,1.727 0.203,0.152 10 kΩ 0.304,4.034 0.514,4.196 0.21,0.162 10 °C 0.243,4.233 0.54,4.395 0.296,0.162 10 (°F) 1.574,2.846 1.308,3.198 1.308,3.198 1.308,3.334 false

Remove the engine coolant temperature sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 2.32 to 2.59 kΩ
80°C (176°F) 0.31 to 0.326 kΩ


Text in Illustration
*1 Ohmmeter
*2 Engine Coolant Temperature Sensor
*3 Acceptable

NOTICE:

When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.


HINT:

Alternative procedure: Connect an ohmmeter to the installed ECT sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.



c.

Reinstall the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CRANKSHAFT POSITION SENSOR)

NG

20.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.
A160890E14
0.229,0.208 0.51,0.417 0.281,0.208 10 false *1

Disconnect the fuel pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 2 20°C (68°F) 16.4 kΩ or less
2 - 1 20°C (68°F) 3 kΩ or less


Text in Illustration
*1 Component without harness connected
(Fuel Pressure Sensor)


c.

Reconnect the fuel pressure sensor connector.


Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

REPLACE COMMON RAIL ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B59-26 (PCR1) - B92-2 (PCR1) Always Below 1 Ω
B59-18 (VC) - B92-3 (VC1) Always Below 1 Ω
B59-28 (E2) - B92-1 (E1) Always Below 1 Ω
B59-26 (PCR1) or B92-2 (PCR1) - Body ground Always 10 kΩ or higher
B59-18 (VC) or B92-3 (VC1) - Body ground Always 10 kΩ or higher
B59-28 (E2) or B92-1 (E1) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connectors.


e.

Reconnect the fuel pressure sensor connector.


Result:
Proceed to
OK
NG



OK

22.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.REPLACE ECM
a.

Replace the ECM (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECM>REMOVAL).

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



b.

Check if the engine starts smoothly or if the engine stalls.

OK:

The engine starts smoothly and does not stall.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY