Refer to DTC P0087 (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0087).
Refer to DTC P0088 (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0088).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0093 | DTC is output when following conditions (a), (b) and (c) are all met and if difference of common rail pressure that fuel pressure sensor detects before and after fuel injection varies greatly from difference of value that ECM calculates before and after fuel injection, ECM determines that there may be fuel leaks (1 trip detection logic).
(a) Engine speed is 1500 rpm or higher. (b) Fuel pressure sensor is normal (P0190, P0192, and P0193 are not detected). (c) Suction control valve is normal (P0088, P0627 and P1229 are not detected). |
·
Fuel leak (injection or supply pump assembly to common rail assembly to injector assembly) ·
Injector assembly ·
Injection or supply pump assembly (suction control valve) ·
Wire harness or connector ·
Common rail assembly ·
ECM |
Refer to DTC P0087 (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0087).
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0087, P0088, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204, P0627, P062D or P1229 is not output | A |
| DTC P0087, P0088, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204, P0627, P062Dor P1229 is output | B |
A
B
By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail assembly internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.
Visually check the injection or supply pump assembly, injector assembly and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.
There may be fuel leaks inside the components, such as the injection or supply pump assembly.
No leakage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the Injection or supply pump assembly (suction control valve) (Click hereEngine / Hybrid System>N04C-VQ (FUEL)>FUEL SUPPLY PUMP>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the suction control valve connector and then start the engine.
Engine does not start.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.
Read the value.
| Engine Speed | Result |
|---|---|
| Idling | 1350 to 2200 mA |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.
Read the value.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Fuel Press | Idling | 20000 to 30000 kPa |
| 3000 rpm without Load | 130000 to 150000 kPa | |
| Target Common Rail Pressure | Idling | Deviation from Fuel Press within 5000 kPa |
| 3000 rpm without Load | Deviation from Fuel Press within 5000 kPa |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the ECM connector.
Disconnect the fuel pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-16 (PCR1) - m1-2 (PCR1) | Always | Below 1 Ω |
| B104-13 (VC) - m1-1 (VC1) | Always | Below 1 Ω |
| B104-14 (E2) - m1-3 (E1) | Always | Below 1 Ω |
| B105-2 (PCR2) - m1-5 (PCR2) | Always | Below 1 Ω |
| B105-13 (VC2) - m1-6 (VC2) | Always | Below 1 Ω |
| B105-14 (E21) - m1-4 (E2) | Always | Below 1 Ω |
| B105-16 (PCR1) or m1-2 (PCR1) - Body ground | Always | 10 kΩ or higher |
| B104-13 (VC) or m1-1 (VC1) - Body ground | Always | 10 kΩ or higher |
| B105-2 (PCR2) or m1-5 (PCR2) - Body ground | Always | 10 kΩ or higher |
| B105-13 (VC2) or m1-6 (VC2) - Body ground | Always | 10 kΩ or higher |
| B104-14 (E2) or m1-3 (E1) - Other terminals | Always | 10 kΩ or higher |
| B105-14 (E21) or m1-4 (E2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Wiggle the fuel pressure sensor connector and check that the fuel pressure reading does not change.
The fuel pressure reading does not change.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTC (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Warm up the engine.
Drive the vehicle by 1500 rpm or more for 5 minutes.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTC.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0093 is output | B |
A
B
Inspect the fuel injection system circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>Fuel Injection System).
Check whether the malfunction has been repairedsuccessfully.
Malfunction has been repaired successfully.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B103-23 (PCV+) - B52-1 (SCV+) | Always | Below 1 Ω |
| B103-12 (PCV-) - B52-2 (SCV-) | Always | Below 1 Ω |
| B103-23 (PCV+) or B52-1 (SCV+) - Body ground | Always | 10 kΩ or higher |
| B103-12 (PCV-) or B52-2 (SCV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-16 (PCR1) - B104-14 (E2) | Idling | 1.7 to 2.2 V |
| B105-2 (PCR2) - B105-14 (E21) | Idling | 1.2 to 1.6 V |
| *a | Component with harness connected
(ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG