Home › Engine / Hybrid System › 2TR-FE (LUBRICATION) › OIL PUMP
RM2850E _51 Engine / Hybrid System _073292 2TR-FE LUBRICATION _0357002 OIL PUMP A

2TR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11301C 1.INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

a.
A097921E06
1.521,1.219 1.104,0.385 1.104,0.385 1.615,0.698 false 0.833,0.146 1.198,0.333 0.365,0.188 10 false SST

Place the timing chain or belt cover sub-assembly on wooden blocks.


b.

Using SST and hammer, tap in the timing gear case or timing chain case oil seal until its surface is flush with the timing gear case edge.

SST
09223-75010  
09950-70010  (09951-07100)


c.

Apply a light coat of MP grease to a new oil seal lip.


Hide 16100 2.INSTALL WATER PUMP ASSEMBLY

a.
A087223

Install a new gasket and the water pump assembly with the 8 bolts.

Torque:

8.9 N*m (91 kgf*cm, 79 in.*lbf)



Hide 11302 3.INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

a.
A431328E01
1.031,1.552 1.906,0.656 1.906,0.656 1.698,1.375 true 1.75,2.26 1.927,2.146 false 1.938,0.479 2.25,0.677 0.313,0.198 10 false *1 1.948,2.021 2.26,2.219 0.313,0.198 10 false *2

Install 3 new O-rings onto the timing chain or belt cover sub-assembly as shown in the illustration.

Text in Illustration
*1 Water Pump O-ring
*2 Oil Pump O-ring


b.
A058128E12
1.677,0.896 1.396,0.354 false 1.271,0.198 1.885,0.396 0.615,0.198 10 false *a

Apply adhesive to the timing chain cover plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Text in Illustration
*a Adhesive


c.
G036021

Using a 10 mm socket hexagon wrench, install the timing chain cover plug.


d.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


A346877E01
0.833,0.688 0.969,0.688 0.969,0.688 1.146,1.125 true 4.094,0.594 4.229,0.594 4.229,0.594 4.406,1.031 true 6.76,1.208 6.625,1.208 6.625,1.208 6.417,1.49 false 3.625,2.042 3.531,2.042 3.531,2.042 3.219,1.708 false 0.823,3.406 0.708,3.406 0.708,3.406 0.635,3.479 false 4.906,1.729 4.823,1.729 4.823,1.729 4.74,1.583 true 6,5.906 5.885,5.906 5.885,5.906 5.813,5.979 false 5.01,7.188 4.875,7.365 4.875,7.365 4.771,7.365 false 0.698,0.625 0.802,0.833 0.104,0.208 10 false F 2.854,0.927 2.979,1.094 0.125,0.167 10 true A 3.583,1.156 4.104,1.365 0.521,0.208 10 true 13 mm 3.292,0.927 3.417,1.094 0.125,0.167 10 true A 3.594,1.406 4.115,1.615 0.521,0.208 10 true 46 mm 0.073,1.115 0.594,1.323 0.521,0.208 10 false 12 mm 0.083,1.385 0.604,1.594 0.521,0.208 10 false 52 mm 3.958,0.521 4.094,0.729 0.135,0.208 10 false H 6.833,1.135 6.969,1.344 0.135,0.208 10 false J 3.885,1.771 4.406,1.979 0.521,0.208 10 false 20 mm 6.635,1.792 7.156,2 0.521,0.208 10 false 20 mm 3.688,1.969 4.208,2.177 0.521,0.208 10 false G 0.24,2.844 0.76,3.052 0.521,0.208 10 false A - A 0.021,3.073 0.552,3.281 0.531,0.208 10 false 2.0 mm 1.094,2.823 1.615,3.031 0.521,0.208 10 false *3 0.885,3.333 1.052,3.5 0.167,0.167 10 false *3 4.938,1.656 5.135,1.865 0.198,0.208 10 true J 0.573,4.094 1.094,4.302 0.521,0.208 10 false F 4.896,4.104 5.417,4.313 0.521,0.208 10 false H 0.604,4.427 1.125,4.635 0.521,0.208 10 false E 1.354,4.438 1.875,4.646 0.521,0.208 10 false E 2.917,4.469 3.115,4.656 0.198,0.188 10 false D 2.917,4.115 3.115,4.302 0.198,0.188 10 false G 3.688,4.469 3.885,4.656 0.198,0.188 10 false D 4.49,4.552 5.167,4.792 0.677,0.24 10 false 56.5 mm 5.281,4.469 5.417,4.708 0.135,0.24 10 false I 5.719,4.375 5.854,4.615 0.135,0.24 10 true I 0.698,4.938 0.813,5.146 0.115,0.208 10 true C 1.229,4.917 1.365,5.104 0.135,0.188 10 true C 2.948,4.938 3.073,5.146 0.125,0.208 10 true B 3.521,4.948 3.646,5.156 0.125,0.208 10 true B 0.292,5.385 0.813,5.594 0.521,0.208 10 false E - E 2.469,5.365 2.99,5.573 0.521,0.208 10 false D - D 4.75,5.417 5.271,5.625 0.521,0.208 10 false I - I 1.448,5.625 2.01,5.854 0.563,0.229 10 false 2.5 mm 1.083,6.24 1.417,6.469 0.333,0.229 10 false *5 0.458,5.792 0.792,6.021 0.333,0.229 10 false *4 3.063,6.198 3.396,6.427 0.333,0.229 10 false *5 5.646,5.448 5.979,5.677 0.333,0.229 10 false *5 3.042,7.406 3.375,7.635 0.333,0.229 10 false *5 1.073,7.385 1.406,7.615 0.333,0.229 10 false *5 0.479,6.958 0.813,7.188 0.333,0.229 10 false *4 2.313,5.615 2.875,5.844 0.563,0.229 10 false 2.5 mm 2.417,6.917 2.979,7.146 0.563,0.229 10 false 6.0 mm 1.51,6.792 2.073,7.021 0.563,0.229 10 false 7.0 mm 3.635,6.958 3.969,7.188 0.333,0.229 10 false *4 3.625,5.76 3.958,5.99 0.333,0.229 10 false *4 0.323,6.625 0.844,6.833 0.521,0.208 10 false C - C 4.969,5.875 5.302,6.104 0.333,0.229 10 false *6 6.052,5.813 6.219,5.979 0.167,0.167 10 false *3 2.479,6.625 3,6.833 0.521,0.208 10 false B - B 4.75,6.635 5.271,6.844 0.521,0.208 10 false J 4.604,7.281 4.938,7.51 0.333,0.229 10 false *3 5.76,6.688 6.094,6.917 0.333,0.229 10 false *1 5.656,7.229 5.99,7.458 0.333,0.229 10 false *2

Text in Illustration
*1 Cylinder Head *2 Cylinder Block
*3 Seal Packing *4 Seal Packing Thickness
*5 Seal Packing Width *6 Protrusion

Application Specification:
Area Seal Packing Diameter Distance from Edge of Cover to Center of Seal Packing Seal Packing Application Length Protrusion from Cylinder Head
A - A
(Dashed line)
2.5 to 4.0 mm (0.0984 to 0.157 in.) 2.0 mm (0.0787 in.) - -
B - B
(Continuous line)
12 to 16 mm (0.472 to 0.630 in.) wide and 2.5 to 4.0 mm (0.0984 to 0.157 in.) thick 6.0 mm (0.236 in.) 36 mm (1.42 in.) from top of bolt hole -
C - C
(Continuous line)
10 to 14 mm (0.394 to 0.551 in.) wide and 2.5 to 4.0 mm (0.0984 to 0.157 in.) thick 7.0 mm (0.276 in.) 52 mm (2.05 in.) from top of bolt hole -
D - D
(Continuous line)
9.0 to 13 mm (0.354 to 0.512 in.) wide and 2.5 to 4.0 mm (0.0984 to 0.157 in.) thick - 12 mm (0.472 in.) from top of bolt hole -
E - E
(Continuous line)
9.0 to 13 mm (0.354 to 0.512 in.) wide and 2.5 to 4.0 mm (0.0984 to 0.157 in.) thick - 12 mm (0.472 in.) from top of bolt hole -
I - I
(Continuous line)
8.0 mm (0.315 in.) - 56.5 mm (2.22 in.) from bottom of cylinder head 2.0 to 3.0 mm (0.0787 to 0.118 in.)
J 8.0 mm (0.315 in.) - 20 mm (0.787 in.) -


NOTICE:
·

Remove any oil from the contact surface.

·

Install the timing chain or belt cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying the seal packing.

·

Do not start the engine for at least 4 hours after installing.




e.
G038475E07
1.219,0.125 0.781,0.125 0.781,0.125 0.521,0.542 false 1.906,1.896 2.156,1.896 2.156,1.896 2.604,1.719 false 1.24,0.031 1.438,0.198 0.198,0.167 10 false *1 1.698,1.813 1.885,1.99 0.188,0.177 10 false *2

Align the oil pump's drive rotor spline and crankshaft as shown in the illustration. Install the spline and chain cover plate onto the crankshaft.

Text in Illustration
*1 Drive Rotor Spline
*a Crankshaft


f.

Temporarily install the timing chain or belt cover sub-assembly with the 18 bolts and nut.

NOTICE:
·

Do not put any oil to the bolt treads.

·

Remove any oil from the bolts and bolt holes.




g.

Excluding bolt A, tighten the bolts and nut in this order: Area 1, Area 2, Area 3.

Torque:

23 N*m (235 kgf*cm, 17 ft.*lbf)


HINT:

Bolt length:

75 mm (2.95 in.) for bolt A

75 mm (2.95 in.) for bolt B

90 mm (3.54 in.) for bolt C



h.

Tighten the bolts labeled A in this order: Area 2 and Area 3.

Torque:

57 N*m (581 kgf*cm, 42 ft.*lbf)



i.

Tighten the bolts labeled D for Area 4.

Torque:

21 N*m (214 kgf*cm, 15 ft.*lbf)


HINT:

Bolt length:

40 mm (1.57 in.) for bolt D


A346878E01
0.854,0.979 0.448,0.573 0.448,0.573 0.823,0.573 true 0.688,0.323 1.385,0.75 true 2.104,0.958 2.406,0.677 2.406,0.677 2.125,0.583 true 1.646,1.031 1.833,1.271 true 2.073,1.333 2.385,1.427 true 2.031,2.063 2.167,2 2.167,2 2.104,1.896 true 1.979,2.469 2.083,2.396 2.083,2.396 2,2.292 true 0.875,2.458 0.719,2.375 0.719,2.375 0.833,2.271 false 0.823,2.042 0.615,1.792 0.615,1.792 0.865,1.542 false 1.125,1.417 0.542,1.281 0.542,1.281 0.854,1.292 false 2.948,2.302 3.229,2.198 3.229,2.198 2.927,2 true 5.448,0.948 5.688,0.656 5.688,0.656 5.469,0.573 true 4.146,0.958 3.938,0.51 3.938,0.51 4.115,0.573 true 3.531,1.042 5.802,1.042 false 3.573,1.448 5.802,1.448 false 4.156,2.021 3.99,1.771 3.99,1.771 4.198,1.521 false 5.375,2.073 5.51,2.01 5.51,2.01 5.448,1.906 true 6.281,2.167 6.542,2.063 6.542,2.063 6.26,1.865 true 0.302,0.49 0.458,0.688 0.156,0.198 10 false A 0.573,0.198 0.729,0.396 0.156,0.198 10 false B 2.438,0.583 2.594,0.781 0.156,0.198 10 false A 1.563,0.875 1.719,1.073 0.156,0.198 10 false *1 2.427,1.344 2.583,1.542 0.156,0.198 10 false B 2.229,1.938 2.385,2.135 0.156,0.198 10 false A 2.135,2.323 2.292,2.521 0.156,0.198 10 false B 0.604,2.302 0.76,2.5 0.156,0.198 10 false B 0.469,1.719 0.625,1.917 0.156,0.198 10 false A 0.417,1.198 0.573,1.396 0.156,0.198 10 false C 3.25,2.125 3.406,2.323 0.156,0.198 10 false D 5.74,0.573 5.896,0.771 0.156,0.198 10 false A 3.854,0.354 4.01,0.552 0.156,0.198 10 false A 3.635,0.125 3.792,0.323 0.156,0.198 10 false *c 3.573,1.073 3.729,1.271 0.156,0.198 10 false *a 3.573,1.479 3.729,1.677 0.156,0.198 10 false *b 3.854,1.698 4.01,1.896 0.156,0.198 10 false A 5.542,2.021 5.698,2.219 0.156,0.198 10 false A 6.583,2 6.74,2.198 0.156,0.198 10 false D 6.156,1.438 6.313,1.635 0.156,0.198 10 false *d

Text in Illustration
*1 Nut - -
*a Area 1 *b Area 2
*c Area 3 *d Area 4


Hide 12101 5.INSTALL OIL PAN SUB-ASSEMBLY

a.

Apply seal packing in a continuous line as shown in the illustration.

A431348E01
0.917,0.375 1.229,0.573 0.313,0.198 10 false *1 0.49,1 0.677,1.198 0.188,0.198 10 true A 0.792,1 0.979,1.198 0.188,0.198 10 true A 2.51,1.021 2.698,1.219 0.188,0.198 10 true C 2.802,1.021 2.958,1.198 0.156,0.177 10 true C 1.552,1.594 1.688,1.771 0.135,0.177 10 true B 1.552,1.927 1.688,2.104 0.135,0.177 10 true B 4.625,0.135 5.01,0.323 0.385,0.188 10 false A - A 5.979,0.125 6.365,0.313 0.385,0.188 10 false B - B 4.531,1.344 4.917,1.531 0.385,0.188 10 false C - C 4.052,0.479 4.438,0.667 0.385,0.188 10 false *c 5.479,0.458 5.771,0.646 0.292,0.188 10 false *c 4.333,1.563 4.719,1.75 0.385,0.188 10 false *c 5.25,1.594 5.635,1.781 0.385,0.188 10 false *a 6.115,0.365 6.5,0.552 0.385,0.188 10 false *b 4.708,0.354 5.094,0.542 0.385,0.188 10 false *a

Text in Illustration
*1 Seal Packing - -
*a 8.0 mm(0.315 in.) *b 6.5 mm(0.256 in.)

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2 to 3 mm (0.079 to 0.118 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after the installation.




b.
A430977E01
0.563,0.854 0.5,0.344 0.5,0.344 0.948,0.51 false 0.615,0.594 0.5,0.344 false 0.531,1.292 0.208,1.802 0.208,1.802 0.917,1.74 false 0.594,1.635 0.219,1.792 false 1.333,1.76 1.073,1.906 1.073,1.906 2.135,1.771 false 1.74,1.76 1.094,1.896 false 3.146,0.875 3.24,1.063 3.24,1.063 3.177,1.281 false 2.563,1.781 2.542,2 2.542,2 2.885,1.771 true 2.552,0.469 2.698,0.25 2.698,0.25 2.885,0.5 true 2.135,0.49 2.135,0.219 2.135,0.219 2.24,0.219 false 1.76,0.469 1.76,0.365 false 1.365,0.479 1.333,0.24 1.333,0.24 1.219,0.24 false 1.073,0.698 1.25,0.865 0.177,0.167 10 false 1 2.104,1.302 2.281,1.469 0.177,0.167 10 true 2 0.802,1.333 0.979,1.5 0.177,0.167 10 true 6 0.802,0.927 0.979,1.094 0.177,0.167 10 false 8 0.813,0.729 0.99,0.896 0.177,0.167 10 false 9 0.792,1.115 0.969,1.281 0.177,0.167 10 false 7 1.073,1.344 1.25,1.51 0.177,0.167 10 false 5 1.333,1.302 1.51,1.469 0.177,0.167 10 true 4 1.729,1.302 1.906,1.469 0.177,0.167 10 true 3 2.063,0.76 2.271,0.958 0.208,0.198 10 true 12 1.281,0.76 1.458,0.927 0.177,0.167 10 true 10 2.438,0.771 2.635,0.979 0.198,0.208 10 true 13 1.646,0.771 1.823,0.938 0.177,0.167 10 false 11 2.677,0.708 2.854,0.875 0.177,0.167 10 false 14 2.469,1.313 2.646,1.479 0.177,0.167 10 true 18 2.74,0.927 2.917,1.094 0.177,0.167 10 false 15 2.708,1.135 2.885,1.302 0.177,0.167 10 true 16 2.719,1.354 2.896,1.521 0.177,0.167 10 false 17 0.979,1.854 1.135,2.031 0.156,0.177 10 false A 2.469,1.99 2.656,2.177 0.188,0.188 10 false B 3.271,0.969 3.427,1.146 0.156,0.177 10 false A 0.385,0.156 0.542,0.333 0.156,0.177 10 false A 1.698,0.198 1.854,0.375 0.156,0.177 10 false A 2.625,0.073 2.781,0.25 0.156,0.177 10 false B 0.115,1.771 0.271,1.948 0.156,0.177 10 false B 1.063,0.146 1.219,0.323 0.156,0.177 10 false *1 2.26,0.115 2.417,0.292 0.156,0.177 10 false *1

Temporarily install the oil pan sub-assembly with the 16 bolts and 2 nuts.

Text in Illustration
*1 Nut

HINT:

Bolt length:

20 mm (0.79 in.) for bolt A

40 mm (1.57 in.) for bolt B



c.

Uniformly tighten the 16 bolts and 2 nuts in the order shown in the illustration.

Torque:

26 N*m (265 kgf*cm, 19 ft.*lbf)



Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer sub-assembly with the bolt and 2 nuts.

Torque:

26 N*m (265 kgf*cm, 19 ft.*lbf)



Hide 12102A 7.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.
A099221E11
1.667,1.917 2.375,2.292 0.708,0.375 10 false A - A 2.271,2.198 3.135,2.563 0.865,0.365 10 false *b 1.365,2.188 1.75,2.365 0.385,0.177 10 false *a 0.448,0.667 0.625,0.875 0.177,0.208 10 false A 0.865,0.667 1.042,0.875 0.177,0.208 10 true A 0.594,3.135 1.563,3.323 0.969,0.188 10 false *1

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.5 mm (0.098 to 0.138 in.)


Text in Illustration
*1 Seal Packing
*a 6.0 mm (0.236 in.)
*b Seal Diameter
2.5 to 3.5 mm (0.098 to 0.138 in.)


b.
A099214E06
1.51,0.229 1.688,0.406 0.177,0.177 10 false 4 0.198,0.229 0.375,0.406 0.177,0.177 10 false 19 2.844,1.656 3.052,1.833 0.208,0.177 10 true 9 2.865,0.667 3.042,0.844 0.177,0.177 10 true 1 2.979,1.146 3.156,1.323 0.177,0.177 10 false 8 0.094,1.031 0.271,1.208 0.177,0.177 10 false 3 2.438,0.51 2.615,0.688 0.177,0.177 10 true 7 1.219,1.813 1.396,1.99 0.177,0.177 10 false 2 2.135,0.417 2.313,0.594 0.177,0.177 10 true 6 1.802,0.25 1.979,0.427 0.177,0.177 10 false 5 0.125,1.792 0.302,1.969 0.177,0.177 10 false 16 0.875,1.865 1.052,2.042 0.177,0.177 10 false 14 1.49,1.813 1.667,1.99 0.177,0.177 10 false 13 1.792,1.802 2.052,1.979 0.26,0.177 10 false 12 0.531,1.948 0.729,2.125 0.198,0.177 10 false 15 2.073,1.813 2.385,1.99 0.313,0.177 10 false 11 2.344,1.823 2.521,2 0.177,0.177 10 true 10 1.156,0.24 1.333,0.417 0.177,0.177 10 false 22 0.896,0.208 1.073,0.385 0.177,0.177 10 false 21 0.604,0.115 0.781,0.292 0.177,0.177 10 false 20 0.094,0.625 0.271,0.802 0.177,0.177 10 false 18 0.063,1.406 0.281,1.583 0.219,0.177 10 false 17

Temporarily install the No. 2 oil pan sub-assembly with the 20 bolts and 2 nuts.


c.

Uniformly tighten the 20 bolts and 2 nuts in the sequence shown in the illustration.

Torque:

9.0 N*m (92 kgf*cm, 80 in.*lbf)



d.

Install a new gasket and the drain plug.


Hide 13471 8.INSTALL CRANKSHAFT PULLEY SUB-ASSEMBLY

Hide 11201 11.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12108 12.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 16268 13.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install a new gasket and the No. 1 water by-pass pipe with the 2 nuts.

Torque:

18 N*m (184 kgf*cm, 13 ft.*lbf)



Hide 88431 14.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 11452 15.INSTALL OIL LEVEL DIPSTICK GUIDE

Hide 15301 16.INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 16603 17.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16331A 19.INSTALL THERMOSTAT

Hide 16321 20.INSTALL WATER INLET

Hide 16620D 21.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 19500 23.INSTALL IGNITION COIL ASSEMBLY

Hide 12311 25.INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET RH

Hide 51202 27.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

Hide 45450 28.INSTALL STEERING RELAY ROD ASSEMBLY

Hide 33110 29.INSTALL MANUAL TRANSMISSION ASSEMBLY

Hide 87246A 33.CONNECT HEATER WATER HOSE OUTLET E

Hide 87245A 34.CONNECT HEATER WATER HOSE INLET A

Hide 88320 36.INSTALL COMPRESSOR AND MAGNETIC CLUTCH

Hide 27020 37.INSTALL GENERATOR ASSEMBLY (for 80A Type)

Hide 27020 38.INSTALL GENERATOR ASSEMBLY (for 100A Type)

Hide 44310 39.INSTALL VANE PUMP ASSEMBLY

Hide 44360 40.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 22030 41.INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 17861 42.INSTALL INTAKE AIR CONNECTOR

Hide 17410 43.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 16400 44.INSTALL RADIATOR ASSEMBLY

Hide 45.CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Torque:

5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 48.INSPECT FOR FUEL LEAK