Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM J

N04C-VL ENGINE CONTROL  ECD SYSTEM  Engine Difficult to Start or Stalling  


WIRING DIAGRAM

Refer to DTC P0087 for fuel pressure sensor circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0087).

Refer to DTC P0115 for engine coolant temperature sensor circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0115).

Refer to DTC P0201 for injector circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0201).

Refer to DTC P0335 for crankshaft position sensor circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>P0335).

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.

·

If the vehicle runs out of fuel while the engine is operating, there is a chance that the engine may be difficult to restart after fuel is refilled.



PROCEDURE

1.CHECK OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTCs related to engine B



A

2.CHECK FUEL FILTER ASSEMBLY

B

2.CHECK FUEL FILTER ASSEMBLY
a.

Check that the fuel filter is not clogged.

OK:

Fuel filter is not clogged.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE CRANKING CONDITION

NG

REPLACE FUEL FILTER ASSEMBLY

3.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.


b.

Compare the cranking condition with that of a normal engine of the same model, and carefully check if there is any difference between them.

OK:

Engine cranking condition is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FUEL PRESS)

NG

CHECK AND REPLACE BATTERY, CHARGING SYSTEM, STARTER ASSEMBLY AND STARTING SYSTEM

4.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Read the value.

Standard:
GTS Display Condition Reference Value
Fuel Press Cranking, and engine coolant temperature 0°C (32°F) or more 15000 kPa or more



Result:
Proceed to
OK
NG



OK

5.CHECK IF INITIAL COMBUSTION OCCURS

NG

BLEED AIR FROM FUEL SYSTEM

5.CHECK IF INITIAL COMBUSTION OCCURS
a.

Check if initial combustion occurs.


Result:
Result Proceed to
Initial combustion occurs OK
No initial combustion NG



OK

6.READ VALUE USING GTS (FUEL PRESS)

NG

7.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
6.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Check that the internal fuel pressure of the common rail assembly is within the specification below.

Standard:
GTS Display Condition Reference Value
Fuel Press Idling Approximately 25000 to 35000 kPa



Result:
Proceed to
OK
NG



OK

7.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

NG

13.CHECK IF FUEL IS BEING SUPPLIED TO INJECTION OR SUPPLY PUMP ASSEMBLY
7.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

Result:
Proceed to
OK
NG



OK

8.INSPECT EXHAUST RETARDER ASSEMBLY

NG

REPAIR OR REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

8.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (FUEL PRESS AND INJECTION VOLUME)

NG

REPLACE EXHAUST RETARDER ASSEMBLY

9.READ VALUE USING GTS (FUEL PRESS AND INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

Fuel Press

·

Injection Volume


Standard:
GTS Display Condition* Reference Value
Fuel Press Idling 25000 to 35000 kPa
Injection Volume Idling 5.0 to 15.0 mm3/st


HINT:

*: If no idling conditions are specified, the shift lever should be in neutral, and the A/C switch and all accessory switches should be off.



Result:
Proceed to
OK
NG



OK

10.CHECK CYLINDER COMPRESSION PRESSURE

NG

14.CHECK ECM TERMINAL VOLTAGE (THW TERMINAL)
10.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click hereEngine / Hybrid System>N04C-VL (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

11.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)
a.

Check the wire harness between the injector assembly and injector driver assembly (IJ terminal).

i.

Disconnect the injector assembly connectors.


ii.

Disconnect the injector driver assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 - B98-5 (INJ1) Always Below 1 Ω
i2-2 - B96-4 (INJ2) Always Below 1 Ω
i3-2 - B96-2 (INJ3) Always Below 1 Ω
i4-2 - B98-4 (INJ4) Always Below 1 Ω
i1-1 - B98-1 (COM1) Always Below 1 Ω
i2-1 - B98-2 (COM2) Always Below 1 Ω
i3-1 - B98-2 (COM2) Always Below 1 Ω
i4-1 - B98-1 (COM1) Always Below 1 Ω
i1-2 or B98-5 (INJ1) - Body ground Always 10 kΩ or higher
i2-2 or B96-4 (INJ2) - Body ground Always 10 kΩ or higher
i3-2 or B96-2 (INJ3) - Body ground Always 10 kΩ or higher
i4-2 or B98-4 (INJ4) - Body ground Always 10 kΩ or higher
i1-1 or B98-1 (COM1) - Body ground Always 10 kΩ or higher
i2-1 or B98-2 (COM2) - Body ground Always 10 kΩ or higher
i3-1 or B98-2 (COM2) - Body ground Always 10 kΩ or higher
i4-1 or B98-1 (COM1) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

12.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)

12.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.


e.

Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

Result:
Result Proceed to
Engine Idling becomes unstable A
Engine Idling does not change B


HINT:
·

If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.





A

REPLACE INJECTOR DRIVER ASSEMBLY

B

13.CHECK IF FUEL IS BEING SUPPLIED TO INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet pipe from the injection or supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the injection or supply pump assembly.

OK:

Fuel is properly supplied to the injection or supply pump assembly when the priming pump is operated.



Result:
Proceed to
OK
NG



OK

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

NG

CHECK AND REPLACE FUEL PIPE CLOGGING (INCLUDING FUEL FREEZING) (FUEL TANK - INJECTION OR SUPPLY PUMP ASSEMBLY)

14.CHECK ECM TERMINAL VOLTAGE (THW TERMINAL)
a.
A260250E35
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 1.625,0.802 1.292,1.542 true 2.198,0.875 2.438,1.542 true 1.385,0.167 1.781,0.354 0.396,0.188 10 false B105 1.938,0.167 2.302,0.354 0.365,0.188 10 false B104 0.063,0.073 0.219,0.208 0.156,0.135 10 false *a 0.979,1.563 1.49,1.813 0.51,0.25 10 false 9(THW) 2.188,1.563 2.615,1.792 0.427,0.229 10 false 14(E2)

Start the engine.


b.

Measure the voltage of the ECM connector.

Standard Voltage:
Tester Connection Condition Specified Condition
E105-9 (THW) - E104-14 (E2) Idling, engine coolant temperature between 60 and 120°C (140 and 248°F) 0.2 to 1.0 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

15.CHECK TERMINAL VOLTAGE (NE+ AND NE- TERMINALS)

NG

18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
15.CHECK TERMINAL VOLTAGE (NE+ AND NE- TERMINALS)
a.
A257466E12
2.354,0.354 2.802,0.615 0.448,0.26 2.635,0.969 2.906,1.781 true 2.573,0.958 1.708,1.656 true 0.104,0.052 0.281,0.229 0.177,0.177 10 false *a 1.344,4.042 2.594,4.354 1.25,0.313 10 false 20 ms./DIV. 0.104,1.938 0.281,2.115 0.177,0.177 10 false *b 2.76,2.26 3.427,2.531 0.667,0.271 10 false 5 V/DIV. 0.406,3.333 0.646,3.5 0.24,0.167 10 false NE 0.458,2.615 0.698,2.781 0.24,0.167 10 false G 2.896,3.365 3.24,3.531 0.344,0.167 10 false GND 2.896,2.802 3.24,2.969 0.344,0.167 10 false GND 2.417,0.396 2.792,0.563 0.375,0.167 10 false B103 2.688,1.833 3.188,2 0.5,0.167 10 false 7 (NE+) 1.438,1.688 1.906,1.854 0.469,0.167 10 false 8 (NE-)

While idling the engine, check the waveform between the specified terminals of the ECM connector using an oscilloscope.

Standard:
Tester Connection Specified Condition
B103-7 (NE+) - B103-8 (NE-) Correct waveform appears as shown


Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the engine speed.


Text in Illustration
*a Component with harness connected
(ECM)
*b G and NE Signal Waveform


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR
16.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY)
a.

Remove the STARTER relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Ignition Switch Position Specified Condition
ST relay terminal 1 - A57-6 (STA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK ECM TERMINAL VOLTAGE (PCR1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY - ECM)

17.CHECK ECM TERMINAL VOLTAGE (PCR1 TERMINAL)
a.
A260250E22
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 1.521,0.875 0.438,1.542 true 1.698,0.729 1.229,1.719 true 1.698,0.875 1.979,1.542 true 2.198,0.875 2.635,1.719 true 1.385,0.167 1.771,0.354 0.385,0.188 10 false B105 1.927,0.167 2.313,0.365 0.385,0.198 10 false B104 0.021,1.563 0.719,1.781 0.698,0.219 10 false 16 (PCR1) 0.063,0.073 0.313,0.302 0.25,0.229 10 false *a 0.865,1.74 1.469,1.958 0.604,0.219 10 false 2 (PCR2) 2.396,1.74 2.875,1.958 0.479,0.219 10 false 14 (E2) 1.656,1.563 2.26,1.833 0.604,0.271 10 false 14 (E21)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B104-14 (E2) Idling 1.7 to 2.2 V
B105-2 (PCR2) - B105-14 (E21) Idling 1.2 to 1.6 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

20.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.
A126612E17
1.573,2.844 1.313,3.198 1.313,3.198 1.313,3.333 false 0.719,0.333 0.99,0.552 0.271,0.219 10 false *1 0.635,1.688 0.813,1.833 0.177,0.146 10 false 30 0.635,1.875 0.813,2.021 0.177,0.146 10 false 20 0.635,2.177 0.813,2.323 0.177,0.146 10 false 10 0.729,2.49 0.823,2.635 0.094,0.146 10 false 5 0.729,3.146 0.823,3.292 0.094,0.146 10 false 1 2.438,2.927 3.271,3.094 0.833,0.167 10 false *2 1.25,3.354 1.99,3.521 0.74,0.167 10 false *a 0.729,2.906 0.823,3.052 0.094,0.146 10 false 2 0.729,2.708 0.823,2.854 0.094,0.146 10 false 3 0.583,3.604 0.802,3.75 0.219,0.146 10 false 0.3 0.583,3.417 0.802,3.563 0.219,0.146 10 false 0.5 0.583,3.948 0.802,4.094 0.219,0.146 10 false 0.1 0.583,3.76 0.802,3.906 0.219,0.146 10 false 0.2 0.885,4.021 1.104,4.167 0.219,0.146 10 false -20 1.281,4.021 1.375,4.177 0.094,0.156 10 false 0 1.542,4.021 1.719,4.167 0.177,0.146 10 false 20 1.885,4.021 2.063,4.167 0.177,0.146 10 false 40 2.219,4.021 2.396,4.167 0.177,0.146 10 false 80 2.594,4.021 2.896,4.167 0.302,0.146 10 false 100 0.875,4.188 1.115,4.365 0.24,0.177 10 false (-4) 1.167,4.188 1.438,4.365 0.271,0.177 10 false (32) 1.479,4.188 1.75,4.365 0.271,0.177 10 false (68) 1.781,4.188 2.125,4.365 0.344,0.177 10 false (104) 2.188,4.188 2.531,4.365 0.344,0.177 10 false (176) 2.594,4.188 2.938,4.365 0.344,0.177 10 false (212) 0.875,1.594 1.073,1.75 0.198,0.156 10 false kΩ 0.271,4.031 0.479,4.198 0.208,0.167 10 false °C 0.24,4.229 0.531,4.396 0.292,0.167 10 false (°F)

Remove the engine coolant temperature sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 2.32 to 2.59 kΩ
1 - 2 80°C (176°F) 0.31 to 0.326 kΩ


Text in Illustration
*1 Ohmmeter
*2 Engine Coolant Temperature Sensor
*a Acceptable

NOTICE:

When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.


HINT:

Alternative procedure: Connect an ohmmeter to the installed engine coolant temperature sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CRANKSHAFT POSITION SENSOR)

NG

20.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Inspect the fuel pressure sensor (Click hereEngine / Hybrid System>N04C-VL (FUEL)>COMMON RAIL>INSPECTION).


Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

REPLACE COMMON RAIL ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B93-2 (PCR1) Always Below 1 Ω
B104-13 (VC) - B93-1 (VC1) Always Below 1 Ω
B104-14 (E2) - B93-3 (E1) Always Below 1 Ω
B105-2 (PCR2) - B93-5 (PCR2) Always Below 1 Ω
B105-13 (VC2) - B93-6 (VC2) Always Below 1 Ω
B105-14 (E21) - B93-4 (E2) Always Below 1 Ω
B105-16 (PCR1) or B93-2 (PCR1) - Body ground Always 10 kΩ or higher
B104-13 (VC) or B93-1 (VC1) - Body ground Always 10 kΩ or higher
B105-2 (PCR2) or B93-5 (PCR2) - Body ground Always 10 kΩ or higher
B105-13 (VC2) or B93-6 (VC2) - Body ground Always 10 kΩ or higher
B104-14 (E2) or B93-3 (E1) - Other terminals Always 10 kΩ or higher
B105-14 (E21) or B93-4 (E2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)

22.REPLACE ECM
a.

Replace the ECM (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECM>REMOVAL).

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECM>INSTALLATION).



b.

Check if the engine starts smoothly or if the engine stalls.

OK:

The engine starts smoothly and does not stall.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY