Home › Engine / Hybrid System › N04C-VJ (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2021.01
RM2850E _51 Engine / Hybrid System _096892 N04C-VJ ENGINE MECHANICAL _0461243 ENGINE ASSEMBLY A

N04C-VJ ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.CHECK INJECTOR COMPENSATION CODE

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 58521D 3.REMOVE ENGINE SERVICE HOLE COVER MAT

a.
A482279

Remove the engine service hole cover mat.


Hide 58410 4.REMOVE ENGINE SERVICE HOLE COVER

a.
A388381

Detach the 2 hooks, 2 guides and remove the engine service hole cover.


Hide 58734B 5.REMOVE REAR ENGINE SERVICE COVER WEATHERSTRIP

a.

Remove the rear engine service cover weatherstrip.


Hide 58420 6.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

a.
A388382C01
0.656,1.698 0.823,1.698 0.823,1.698 0.99,1.365 true 0.479,1.583 0.698,1.771 0.219,0.188 10 true *a
*a Knob


Turn the knob to detach the hook, detach the 2 guides and remove the No. 2 engine service hole cover assembly.


Hide 33820B 8.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C102377

Remove the clip and plate washer and disconnect the transmission control cable assembly from the transmission floor shift assembly.


b.
C178308

Remove the clip.


c.

Remove the bolt and clamp.


d.

Disconnect the transmission control cable assembly from the front engine service cover panel sub-assembly.


Hide 58701A 9.REMOVE FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

a.
C367964

Disconnect the 2 connectors from the transmission floor shift assembly.


b.

Remove the 5 bolts and front engine service cover panel sub-assembly.


Hide 51441D 10.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51446C 11.REMOVE ENGINE UNDER COVER BRACKET LH

a.
A482318

Remove the 2 bolts and the engine under cover bracket LH.


Hide 51445D 12.REMOVE ENGINE UNDER COVER BRACKET RH

a.
A482317

Remove the 2 bolts and the engine under cover bracket RH.


Hide 51456B 13.REMOVE REAR ENGINE UNDER COVER BRACKET LH

a.
A482319

Remove the 2 bolts and engine under cover bracket LH.


Hide 51455B 14.REMOVE REAR ENGINE UNDER COVER BRACKET RH

a.
A482320

Remove the 2 bolts and rear engine under cover bracket RH.


Hide 53712C 15.REMOVE FRONT FENDER APRON LH

a.
A146649

Remove the 6 bolts and the front fender apron LH.


Hide 53711C 16.REMOVE FRONT FENDER APRON RH

a.
A381110

Remove the 7 bolts and the front fender apron RH.


Hide 19.DRAIN AUTOMATIC TRANSMISSION FLUID

Hide 20.DRAIN POWER STEERING FLUID

Hide 16400 21.REMOVE RADIATOR ASSEMBLY

Hide 17410 22.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 46700 23.REMOVE EXHAUST RETARDER ASSEMBLY

Hide 25608 24.REMOVE EGR COOLER SUB-ASSEMBLY

Hide 28100 25.REMOVE STARTER ASSEMBLY

Hide 44348A 26.DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

a.
C397492

Slide the clamp and disconnect the No. 1 oil reservoir to pump hose from the vane pump assembly.


Hide 44411 27.DISCONNECT PRESSURE FEED HOSE

a.
C397498

Remove the union bolt and disconnect the pressure feed hose from the vane pump assembly.


b.

Remove the gasket from the pressure feed hose.


Hide 27020 28.REMOVE GENERATOR ASSEMBLY

Hide 37140 29.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 45470 30.DISCONNECT TIE ROD ASSEMBLY LH

a.
A451484N01
2.469,0.396 2.302,0.396 2.302,0.396 1.844,0.688 false 2.5,0.302 2.865,0.469 0.365,0.167 10 true SST

Remove the cotter pin.


b.

Remove the nut.


c.

Using SST, disconnect the tie rod end assembly LH from the steering relay rod assembly.

SST
09628-62011  


Hide 45450 31.DISCONNECT STEERING RELAY ROD ASSEMBLY

a.
A451478C01
2.521,1.167 2.781,0.417 2.781,0.417 2.906,0.417 true 0.531,3.698 0.708,3.698 0.708,3.698 1.063,3.438 true 0.094,0.042 0.302,0.26 0.208,0.219 10 false *a 0.094,2.438 0.313,2.635 0.219,0.198 10 false *b 2.938,0.323 3.281,0.521 0.344,0.198 10 true SST 0.219,3.615 0.521,3.854 0.302,0.24 10 false SST
*a for Idler Arm Bracket Assembly Side
*b for Center Arm Bracket Assembly Side


Remove the 2 cotter pins.


b.

Remove the 2 nuts.


c.

Using SST, disconnect the steering relay rod assembly from the center arm bracket assembly and idler arm bracket assembly.

SST
09611-20015  


Hide 51202D 32.REMOVE FRONT LOWER SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
A449342

Remove the 6 bolts, 4 nuts, 4 washers and front lower suspension crossmember sub-assembly.

HINT:

While fixing the nut in place, loosen and remove the through bolt.



Hide 82121 34.DISCONNECT ENGINE WIRE

a.
A399647

Remove the 2 bolts and disconnect the engine wire from the No. 1 engine hanger.


b.
A451534C01
0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 0.094,2.406 0.406,2.604 0.313,0.198 10 false *b
*a LH Side
*b RH Side


Remove the 2 bolts and nut, and disconnect the engine wire from the engine assembly.


Hide 87246B 35.DISCONNECT OUTLET HEATER WATER HOSE B

a.
A146506

Slide the clamp and disconnect the outlet heater water hose B.


Hide 87245B 36.DISCONNECT INLET HEATER WATER HOSE B

a.
A146507

Slide the clamp and disconnect the inlet heater water hose B.


Hide 88320 37.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.
A175430

Disconnect the connector.


b.

Remove the 4 bolts and disconnect the cooler compressor assembly.


Hide 44774 38.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A260612

Slide the clamp and disconnect the union to connector tube hose.


Hide 23271F 39.DISCONNECT FUEL HOSE

a.
A482324

Slide the 2 clamps and disconnect the 2 fuel hoses.


Hide 11000 40.REMOVE ENGINE ASSEMBLY

a.

Using an engine lifter, support the engine assembly and height adjustments or plate lift attachments.

NOTICE:
·

Place the height adjustments or plate lift attachments so that the engine assembly is level.

·

As the engine assembly is very heavy, be sure to support it securely.




b.
A146473

Remove the 2 nuts and washer.


c.

Remove the 4 bolts and front No. 1 engine mounting bracket LH.


d.

Remove the engine mounting stabilizer and front engine mounting insulator.


e.
A146472

Remove the 2 nuts and washer.


f.

Remove the 4 bolts and front No. 1 engine mounting bracket RH.


g.

Remove the engine mounting stabilizer and front engine mounting insulator.


h.

Remove the engine assembly.

NOTICE:

When removing the engine assembly be careful not to damage any wire harnesses.



Hide 41.INSTALL ENGINE STAND

a.

Attach an engine sling device and hang the engine assembly with a chain block.

NOTICE:

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.



b.

Install the engine assembly to an engine stand with bolts.

CAUTION:

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.


NOTICE:

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.



c.

Remove the 2 bolts and generator bracket.


d.

Remove the 2 bolts and No. 1 engine hanger.


Hide 12180E 42.REMOVE OIL FILLER CAP ASSEMBLY

a.

Remove the oil filler cap sub-assembly.


Hide 12601B 43.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Remove the 2 bolts and No. 1 engine cover sub-assembly.


Hide 11202D 44.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A482321

Remove the bolt and disconnect the 4 connectors and remove the wire harness.


b.
A482322

Disconnect the PCV hose and, remove the 6 bolts and oil separator assembly.


c.

Remove the 2 bolts, 2 cylinder head cover stay and 2 cylinder head cushion.


d.

Remove the No. 2 cylinder head cover sub-assembly and cylinder head cover gasket.


e.

Remove the 4 No. 2 cylinder head cover gaskets.


Hide 25620 45.REMOVE EGR VALVE ASSEMBLY

Hide 23741B 47.REMOVE INJECTION PIPE CLAMP

Hide 48.REMOVE INJECTION PIPE SUB-ASSEMBLY

Hide 23670 49.REMOVE INJECTOR ASSEMBLY

Hide 16577C 50.REMOVE RADIATOR PIPE

a.
A482323

Remove the 2 bolts and radiator pipe.


b.

Remove the gasket.


Hide 44310 51.REMOVE VANE PUMP ASSEMBLY

a.
C401665

Remove the 2 bolts and remove the vane pump assembly.


b.

Remove the O-ring.


Hide 17201 52.REMOVE TURBOCHARGER SUB-ASSEMBLY

Hide 83420 53.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 11301K 54.REMOVE CRANKSHAFT POSITION SENSOR

Hide 11301M 55.REMOVE CAMSHAFT POSITION SENSOR

Hide 16630G 56.REMOVE IDLER PULLEY ASSEMBLY

a.
A146483

Remove the 2 bolts and idler pulley assembly.


Hide 88440B 57.REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET

a.
A399656

Remove the 3 bolts and idle pulley assembly with bracket.


Hide 88431A 58.REMOVE NO. 2 COMPRESSOR MOUNTING BRACKET

a.
A403297

Remove the 5 bolts and No. 2 compressor mounting bracket.


Hide 88431 59.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A403293

Remove the 2 bolts and No. 1 compressor mounting bracket.


Hide 16331A 60.REMOVE THERMOSTAT

Hide 16333 61.REMOVE WATER OUTLET HOUSING

a.
A146582

Remove the 3 bolts and water outlet housing.


b.

Remove the gasket.


Hide 87208L 62.REMOVE WATER PIPE SUB-ASSEMBLY

a.
A449358

Remove the 3 bolts, water pipe sub-assembly and O-ring.


Hide 63.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A449359

Disconnect the connector.


b.

Slide the clamp and disconnect the water hose.


c.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly.


Hide 16206 64.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A449360

Remove the 8 bolts and water by-pass pipe sub-assembly.


b.

Remove the 2 gaskets and 3 O-rings.


Hide 16100 65.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 23810A 66.REMOVE COMMON RAIL ASSEMBLY

Hide 22214B 67.REMOVE FUEL ADDITION CUT VALVE ASSEMBLY

Hide 22100 68.REMOVE SUPPLY PUMP ASSEMBLY

Hide 69.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY

a.
A258070

Remove the 2 union bolts, 3 gaskets and the No. 4 fuel pipe sub-assembly.


Hide 70.REMOVE NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY

a.
A482325

Remove the nut and the fuel pipe clamp.


b.

Remove the 2 union bolts, 2 gaskets and No. 3 nozzle leakage pipe sub-assembly.


Hide 23811H 71.REMOVE NO. 1 FUEL PIPE

a.
A482327

Remove the nut and the fuel pipe clamp.


b.

Remove the bolt and No. 1 fuel pipe.


Hide 23803H 73.REMOVE FUEL RETURN PIPE SUB-ASSEMBLY

a.
A482326

Remove the union bolt, 2 gaskets and fuel return pipe sub-assembly.


Hide 23310 74.REMOVE UPPER FUEL FILTER BODY

a.
A257901

Remove the 2 bolts and upper fuel filter body.


Hide 19971E 75.REMOVE VACUUM PIPE

a.
A261715

Remove the nut and pipe clamp.


b.

Remove the union bolt, vacuum pipe and 2 gaskets.


Hide 29601B 76.REMOVE VACUUM PUMP OIL PIPE SUB-ASSEMBLY

a.
A399630

Remove the 3 union bolts and vacuum pump oil pipe sub-assembly and 3 gaskets.


Hide 29300 77.REMOVE VACUUM PUMP ASSEMBLY

a.
A399631

Remove the 2 nuts, vacuum pump assembly and O-ring.


Hide 23849G 78.REMOVE FUEL PIPE SUPPORT

a.

Remove the bolt and fuel pipe support.


Hide 23264D 79.REMOVE FUEL FILTER BRACKET

a.
A407664

Remove the 2 bolts and fuel filter bracket.


Hide 80.REMOVE OIL COOLER COVER SUB-ASSEMBLY

Hide 12204 81.REMOVE VENTILATION VALVE SUB-ASSEMBLY

a.
A449355

Slide the clamp and disconnect the hose.


b.

Remove the bolt and ventilation valve sub-assembly.


Hide 16206A 82.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A449356

Remove the 5 bolts and No. 2 water by-pass pipe sub-assembly.


b.

Remove the 3 O-rings.


Hide 17107 83.REMOVE EXHAUST MANIFOLD HEAT INSULATOR SUB-ASSEMBLY

Hide 17141 84.REMOVE EXHAUST MANIFOLD

Hide 17111 85.REMOVE INTAKE MANIFOLD

Hide 23809L 86.REMOVE FUEL PIPE SUPPORT SUB-ASSEMBLY

a.
A347517

Remove the 2 bolts and fuel pipe support sub-assembly.


Hide 23849G 87.REMOVE FUEL PIPE SUPPORT

a.
A257900

Remove the 2 bolts and fuel pipe support.