Be sure to read the precautionary notices concerning the SRS airbag system before servicing it (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
1.INSTALL REAR FLOOR AIRBAG SENSOR
Install the clip.
Install the sensor with the bolt.
If the rear floor airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
When installing the rear floor airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
Check that there is no looseness in the installation parts of the sensor.
Connect the sensor connector.
2.INSTALL REAR FLOOR AIRBAG SENSOR COVER
Attach the 2 claws to install the sensor cover.
58595
3.INSTALL NO. 3 FLOOR CARPET MOULDING
64740A
4.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Captain Seat Type)
64740A
5.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Except Captain Seat Type)
64730B
6.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for Captain Seat Type)
64730B
7.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for Except Captain Seat Type)
64766
8.INSTALL QUARTER TRIM JACK COVER SUB-ASSEMBLY (for LH Side)
64735G
9.INSTALL DECK TRIM SIDE SERVICE HOLE COVER LH
64735F
10.INSTALL DECK TRIM SIDE SERVICE HOLE COVER RH
67887L
11.INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP LH
67887L
12.INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP RH
67918E
13.INSTALL REAR DOOR SCUFF PLATE LH
67917C
14.INSTALL REAR DOOR SCUFF PLATE RH
67918E
15.INSTALL REAR DOOR SCUFF PLATE LH
67917C
16.INSTALL REAR DOOR SCUFF PLATE RH
66311B
17.INSTALL ROPE HOOK
58625D
18.INSTALL REAR FLOOR NO. 1 MAT PLATE (for Tumble Seat Type, Manual Stowing Seat Type)
58625D
19.INSTALL REAR FLOOR NO. 1 MAT PLATE (for Power Stowing Seat Type)
67939D
20.INSTALL BACK DOOR GARNISH CENTER
67935
21.INSTALL BACK DOOR SCUFF PLATE
67881A
22.INSTALL BACK DOOR WEATHERSTRIP
23.INSTALL REAR NO. 2 SEAT ASSEMBLY LH
for Tumble Seat Type:
Install the rear No. 2 seat (see page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Tumble Seat Type LH Side)>INSTALLATION).
for Power Stowing Seat Type:
Install the rear No. 2 seat (see page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type LH Side)>INSTALLATION).
for Manual Stowing Seat Type:
Install the rear No. 2 seat (see page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Manual Stowing Seat Type LH Side)>INSTALLATION).
24.INSTALL REAR NO. 2 SEAT ASSEMBLY RH
for Tumble Seat Type:
Install the rear No. 2 seat (see page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Tumble Seat Type RH Side)>INSTALLATION).
for Power Stowing Seat Type:
Install the rear No. 2 seat (see page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type RH Side)>INSTALLATION).
for Manual Stowing Seat Type:
Install the rear No. 2 seat (see page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Manual Stowing Seat Type RH Side)>INSTALLATION).
64420A
25.INSTALL LUGGAGE ROOM BOX LID ASSEMBLY (for Tumble Seat Type, Manual Stowing Seat Type)
28800
26.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
27.PERFORM INITIALIZATION
Perform initialization (see page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
28.CHECK SRS WARNING LIGHT
Check the SRS warning light (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).