Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2014.09–2016.05
RM24M0E _51 Engine / Hybrid System _059570 CRUISE CONTROL _0292039 CRUISE CONTROL SYSTEM T

CRUISE CONTROL  CRUISE CONTROL SYSTEM  PROBLEM SYMPTOMS TABLE  


HINT:
·

Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Cruise Control System
Symptom Suspected Area See page
Main switch cannot be turned ON. (CRUISE main indicator light on combination meter does not illuminate.) 1. Cruise control switch circuit (Click here)
2. Cruise main indicator circuit (Click here)
3. ECM (2AZ-FE) (Click here)
3. ECM (2GR-FE) (Click here)
4. CAN communication line (Click here)
SET is not occurring or CANCEL is occurring. (DTC is not output.) 1. Cruise control switch circuit (Click here)
2. Combination meter (Click here)
3. ECM (2AZ-FE) (Click here)
3. ECM (2GR-FE) (Click here)
Actual vehicle speed deviates above or below the set speed. 1. Vehicle speed sensor circuit (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
Gear shifting occurs frequently between 3rd and O/D when driving with cruise control on. 1. Vehicle speed sensor circuit (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
Cruise control does not cancel, even when brake pedal is depressed. 1. Stop light switch circuit (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
Cruise control does not cancel, even when transmission is shifted to N. 1. Park / neutral position switch circuit (U241E) (Click here)
1. Park / neutral position switch circuit (U660E) (Click here)
1. Park / neutral position switch circuit (K112) (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
Control switch does not operate. (-/SET, +/RES, CANCEL not position.) 1. Cruise control switch circuit (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
Speed setting cannot be canceled. (CANCEL function fails.) 1. Cruise control switch circuit (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
SET possible at 40 km/h (25 mph) or less, or CANCEL does not operate. 1. Vehicle speed sensor circuit (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
Poor response is ACCEL and RESUME modes. 1. Cruise control switch circuit (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
O/D does not resume, even though road is not uphill. 1. Vehicle speed sensor circuit (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
DTC memory is erased. 1. ECM (2AZ-FE) (Click here)
1. ECM (2GR-FE) (Click here)
DTC is not output, or is output when it should not be. 1. TC and CG terminal circuit (Click here)
2. ECM (2AZ-FE) (Click here)
2. ECM (2GR-FE) (Click here)
Cruise main indicator light remains ON or fails to light. 1. Cruise control switch circuit (Click here)
2. Cruise main indicator circuit (Click here)
3. Combination meter (Click here)
4. ECM (2AZ-FE) (Click here)
4. ECM (2GR-FE) (Click here)