Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM J

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  Engine does not Start  


DESCRIPTION

ENGINE START SYSTEM FUNCTION


a.

If the engine switch is pressed with the shift lever in the P or N position and the brake pedal depressed, the main body ECU determines that it is an engine start request.


b.

The certification ECU and other ECUs perform key verification via the LIN communication line.


c.

The main body ECU activates the ACC relay.


d.

The main body ECU activates the LH-IG Relay 1, LH-IG relay 2, RH-IG Relay 1 and IG2 relays.


e.

The certification ECU outputs a steering UNLOCK signal. The signal is sent to the main body ECU via the steering lock ECU.


f.

The main body ECU sends an engine start request signal to the ECM.


g.

The ECM sends an ACC cut request signal to the main body ECU.


h.

The ECM and main body ECU activate the ST relay.


i.

The main body ECU deactivates the ACC relay until the ECU detects an engine start.


j.

When engine revolution speed reaches 1200 rpm, the ECM determines that the engine has been started.

The ECM stops sending on ACC cut request signal to the main body ECU.

The main body ECU reactivates the ACC relay and turns off the engine switch indicator light, when engine revolution speed reaches 800 rpm.

Symbols of main body ECU Signals
STP Stop light switch ON signal Input
SSW1/SSW2 Engine switch ON signal Input
ACCD ACC relay operation signal Output
SLP Steering lock actuator position signal Input
IG1D LH-IG Relay 1, LH-IG Relay 2 and RH IG Relay 1 operation signal Output
IG2D IG2 relay operation signal Output
STR2 ST relay operation signal (Sub) Output
STR Park/Neutral start switch signal Input
TACH Engine start detection signal Input
STSW Starter activation request signal Output
ACCR ACC cut request signal Input

Symbols of ECM Signals
ACCR ACC cut request signal Output
TACH Engine revolution speed signal Output
STSW Starter activation request signal Input
STAR ST relay operation signal (Main) Output
STA Starter activation signal Input



B168631E02
0.448,0.917 1.292,1.115 0.844,0.198 10 false from Battery 0.656,1.385 1.281,1.563 0.625,0.177 10 false CAN Line 1.844,1.052 2.573,1.208 0.729,0.156 10 false AM2 NO. 2 0.24,2.031 0.76,2.365 0.521,0.333 10 false to Each System 0.417,3.438 0.938,3.771 0.521,0.333 10 false to Each System 2.26,5.135 2.781,5.469 0.521,0.333 10 false to Each System 2.094,2.031 2.74,2.354 0.646,0.323 10 false from ALT Fuse 2.25,3.438 2.896,3.76 0.646,0.323 10 false from ALT Fuse 0.177,5.135 0.823,5.458 0.646,0.323 10 false from IG2 Fuse 1.292,2.865 1.615,3.021 0.323,0.156 10 false ACC 1.167,4.281 2.094,4.458 0.927,0.177 10 false LH-IG Relay 1 1.323,5.948 1.573,6.104 0.25,0.156 10 false IG2 1.302,7.333 1.844,7.49 0.542,0.156 10 false ST CUT 0.927,8.583 1.063,8.75 0.135,0.167 10 false A 2.5,8.583 2.635,8.75 0.135,0.167 10 false B 3.365,0.26 4.531,0.417 1.167,0.156 10 false MAIN BODY ECU 3.052,0.552 3.375,0.708 0.323,0.156 10 false AM1 4.469,0.615 4.885,0.771 0.417,0.156 10 false SSW1 4.469,0.854 4.885,1.01 0.417,0.156 10 false SSW2 4.479,1.083 4.875,1.24 0.396,0.156 10 false INDW 4.51,1.333 4.885,1.49 0.375,0.156 10 false INDS 4.51,1.573 4.885,1.729 0.375,0.156 10 false SWIL 4.573,2.177 4.875,2.333 0.302,0.156 10 false STP 4.573,3.26 4.875,3.417 0.302,0.156 10 false SPD 4.583,4.208 4.885,4.365 0.302,0.156 10 false SLP 4.563,4.51 4.875,4.667 0.313,0.156 10 false LIN1 4.458,6.26 4.885,6.417 0.427,0.156 10 false CANN 4.469,6.417 4.885,6.573 0.417,0.156 10 false CANP 3.052,0.927 3.375,1.083 0.323,0.156 10 false AM2 3.052,1.292 3.521,1.448 0.469,0.156 10 false CANH 3.052,1.448 3.531,1.604 0.479,0.156 10 false CANL 3.052,2.604 3.531,2.76 0.479,0.156 10 false ACCD 3.052,3.99 3.396,4.146 0.344,0.156 10 false IG1D 3.052,5.688 3.396,5.844 0.344,0.156 10 false IG2D 3.052,6.708 3.396,6.865 0.344,0.156 10 false STR 5.938,0.448 6.854,0.594 0.917,0.146 10 false Engine Switch 5.76,2.052 6.865,2.208 1.104,0.156 10 false Stop Light Switch 5.708,3.135 6.917,3.292 1.208,0.156 10 false Combination Meter 5.698,4.26 6.906,4.417 1.208,0.156 10 false Steering Lock ECU 5.75,6.042 6.833,6.198 1.083,0.156 10 false Certification ECU 5.885,5.177 6.708,5.333 0.823,0.156 10 false ID Code Box 4.99,2.656 6.031,2.813 1.042,0.156 10 false to Each System 4.969,3.75 6.01,3.906 1.042,0.156 10 false to Each System 5.969,7.281 6.24,7.458 0.271,0.177 10 false Key 6,7.979 6.24,8.198 0.24,0.219 10 false LIN 6,8.385 6.323,8.583 0.323,0.198 10 false CAN

B166876E01
0.948,0.148 1.089,0.294 0.141,0.146 10 A 2.507,0.148 2.648,0.294 0.141,0.146 10 B 3.052,0.686 3.444,0.842 0.392,0.157 10 STR2 3.052,1.752 3.475,1.908 0.423,0.157 10 GND1 4.454,1.171 4.877,1.328 0.423,0.157 10 STSW 4.463,1.735 4.877,1.891 0.414,0.157 10 TACH 4.463,2.302 4.877,2.459 0.414,0.157 10 ACCR 3.052,1.915 3.466,2.071 0.414,0.157 10 GND2 3.412,3.385 4.572,3.546 1.161,0.161 10 MAIN BODY ECU 3.803,4.169 4.143,4.330 0.340,0.161 10 ECM 0.68,1.464 1.677,1.780 0.997,0.316 10 Park/Neutral Position Switch 1.025,2.998 1.339,3.146 0.314,0.148 10 STA 1.025,3.346 1.374,3.494 0.349,0.148 10 NSW 0.569,3.696 2.249,3.852 1.680,0.157 10 Transmission Control ECU 1.389,5.582 1.593,5.738 0.205,0.157 10 ST 1.432,7.684 1.886,7.845 0.454,0.161 10 Starter 0.652,8.122 1.128,8.292 0.475,0.170 10 Battery 3.056,4.864 3.458,5.016 0.401,0.152 10 STAR 4.461,5.167 4.875,5.319 0.414,0.152 10 ACCR 4.474,5.726 4.875,5.878 0.401,0.152 10 TACH 4.452,6.291 4.875,6.444 0.423,0.152 10 STSW 4.58,7.441 4.876,7.593 0.296,0.152 10 NE+ 4.58,8.211 4.876,8.364 0.296,0.152 10 NE- 3.056,5.282 3.353,5.434 0.296,0.152 10 STA 5.045,7.644 6.768,7.805 1.724,0.161 10 Crankshaft Position Sensor

WIRING DIAGRAM

CAUTION / NOTICE / HINT

EMERGENCY ENGINE START CONTROL


a.

If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU. This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P or N position.

To activate the starter:

i.

Turn the engine switch from off to on (ACC).


ii.

Press and hold the engine switch for 15 seconds.




HINT:

After the main body ECU, certification ECU, steering lock ECU, ID code box and/or ECM are/is replaced, perform the registration procedures for the engine immobiliser system.


PROCEDURE

1.CHECK ENTRY FUNCTION DETECTION AREA
a.
B137958E01
2.59,0.1 3.251,0.448 0.661,0.348 10 Inspection Point 1.843,1.005 2.424,0.18 2.424,0.18 2.547,0.18 false

Inspect entry detection area.

i.

When the electrical key is in either of the 2 inspection points in the illustration, the shift lever is in the P or N position and the brake pedal is depressed, check that the engine switch indicator illuminates in green.

OK:

Engine switch illuminates in green.


HINT:

If the engine switch does not illuminate, perform troubleshooting according to the PROBLEM SYMPTOMS TABLE of the smart entry and start system (starting) (engine switch indicator light does not come on) (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>Engine Switch Indicator Circuit) and the smart entry and start system (entry door lock) (room oscillator does not recognize key) (See page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>Room Oscillator does not Recognize Key).





OK

2.CHECK IF ENGINE STARTS (INITIALIZE STEERING LOCK)

NG

GO TO OTHER PROBLEM

2.CHECK IF ENGINE STARTS (INITIALIZE STEERING LOCK)
a.

Turn the engine switch off.


b.

Make sure that the shift lever is in the P or N position.


c.

Open and close the driver's door.


d.

When the shift lever is in the P or N position and the brake pedal is depressed, check if the engine can be started.

OK:

Steering lock/unlock function operates normally and engine can be started.


HINT:

After the battery is discharged and then recharged, the engine may not start unless the steering lock is initialized using the above procedure (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

END

NG

3.CHECK FOR DTC
3.CHECK FOR DTC

b.

Check for DTCs again.

OK:

No DTC is output.


HINT:
·

If smart entry and start system (starting function) DTCs are output (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

·

If electrical steering lock DTCs are output (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

·
·

If engine control system DTCs output (2GR-FE) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).





OK

4.CHECK ENGINE SWITCH CONDITION

NG

GO TO DTC CHART

4.CHECK ENGINE SWITCH CONDITION
a.

Check the power source mode changes.

i.

When the key is inside the vehicle and the shift lever is in the P or N position, check that pressing the engine switch causes the power source mode to change as follows:

OK:

off → on (ACC) → on (IG) → off


HINT:





OK

5.CHECK CRANKING FUNCTION

NG

GO TO OTHER PROBLEM

5.CHECK CRANKING FUNCTION
a.

Check the engine cranking function.

i.

When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P or N position, check that depressing the brake pedal and pressing the engine switch crank the engine.

Result:
Result Proceed to
Engine does not crank A
Engine cranks B





A

6.READ VALUE USING INTELLIGENT TESTER (P SIGNAL)

B

23.READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST)
6.READ VALUE USING INTELLIGENT TESTER (P SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG)


c.

Read the DATA LIST according to the displays on the tester screen.

Body:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift P Sig Shift P signal / ON or OFF ON: Shift position is P
OFF: Shift position is not P
-

OK:

ON (P signal is ON) and OFF (P signal is OFF) appear on the screen.


HINT:

If the result is not as specified, perform troubleshooting for DTC B2281 ("P" signal malfunction) first (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2281).




OK

7.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)

NG

7.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Read the DATA LIST according to the displays on the tester screen.

Body:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop Light Switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-

OK:

ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.


HINT:

If the result is not as specified, perform troubleshooting for DTC B2284 (Brake signal malfunction) first.




OK

8.READ VALUE USING INTELLIGENT TESTER (STEERING LOCK)

NG

8.READ VALUE USING INTELLIGENT TESTER (STEERING LOCK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).

Body:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Str Unlock SW Steering lock condition / ON or OFF ON: Steering is unlocked (Engine switch on (ACC))
OFF: Steering is locked (Engine switch off)
-

OK:

ON (steering is unlocked) and OFF (steering is locked) appear on the screen.


HINT:

If the result is not as specified, perform troubleshooting for DTCs B2285 (Steering lock position signal circuit malfunction) (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2285) and B2288 (Steering lock signal circuit malfunction) first (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2288).




OK

9.CHECK STEERING LOCK

NG

9.CHECK STEERING LOCK
a.

Check if the steering lock is released when turning the engine switch on (ACC).

OK:

The steering lock is released.




OK

10.INSPECT MAIN BODY ECU (STSW VOLTAGE)

NG

22.READ VALUE USING INTELLIGENT TESTER (L CODE)
10.INSPECT MAIN BODY ECU (STSW VOLTAGE)
a.
U188848E02
1.906,3.406 2.552,3.042 false 0.323,0.073 2.563,0.479 2.24,0.406 10 false Component with harness connected: (Main Body ECU) 2.583,2.938 3,3.094 0.417,0.156 10 false STSW 2.583,3.365 2.927,3.563 0.344,0.198 10 false G60

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G60-4 (STSW) - Body ground Brake pedal depressed, engine switch held on (ST) Output voltage at terminal AM1 or AM2 is 2 V or more.


HINT:

If the result is not as specified, perform troubleshooting for DTC B2275 (STSW monitor malfunction) first (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2275).




OK

11.INSPECT ECM (ACCR VOLTAGE)

NG

11.INSPECT ECM (ACCR VOLTAGE)
a.
U188845E02
1.833,2.635 2.5,2.313 false 0.323,0.135 2.542,0.51 2.219,0.375 10 false Component with harness connected: (Main Body ECU) 2.552,2.167 2.969,2.323 0.417,0.156 10 false ACCR 2.542,2.646 2.875,2.844 0.333,0.198 10 false G58

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G58-3 (ACCR) - Body ground Brake pedal depressed, shift lever N position, engine switch is pushed once → on (IG) 0.1 to 0.8 (*1) → Output voltage at terminal AM1 or AM2 is -2 V or more.


HINT:
·

*1: Voltage is output only when the engine is cranking.

·

If the result is not as specified, perform troubleshooting for DTC B2276 (ACCR signal circuit malfunction) first (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2276).





OK

12.INSPECT MAIN BODY ECU (STR VOLTAGE)

NG

12.INSPECT MAIN BODY ECU (STR VOLTAGE)
a.
U188849E02
1.906,2.073 2.552,1.698 false 0.208,0.083 2.448,0.49 2.24,0.406 10 false Component with harness connected: (Main Body ECU) 2.583,1.583 2.969,1.771 0.385,0.188 10 false STR 2.552,2.115 2.906,2.313 0.354,0.198 10 false G57

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G57-8 (STR) - Body ground Shift lever P position → except P position Below 2 V → Pulse generation



b.

Proceed to the next step based on the inspection result.

Result:
Result Proceed to
NG A
OK B




A

13.INSPECT RELAY (ST CUT)

B

18.INSPECT RELAY (ST)
13.INSPECT RELAY (ST CUT)
a.
B016200

Remove the ST CUT relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 5 When battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

14.INSPECT ECM (STR2 VOLTAGE)

NG

REPLACE ST CUT RELAY

14.INSPECT ECM (STR2 VOLTAGE)
a.
U188850E02
1.906,3.49 2.542,3.042 false 0.323,0.073 2.615,0.385 2.292,0.313 10 false Component with harness connected: (Main Body ECU) 2.573,2.948 2.948,3.104 0.375,0.156 10 false STR2 2.604,3.313 2.896,3.479 0.292,0.167 10 false G60

Disconnect the A7 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G60-6 (STR2) - Body ground Brake pedal depressed, shift lever P position, engine switch on (ST) Output voltage at terminal AM1 or AM2 is -3.5 V or more (*1)


HINT:

*1: Voltage is output for 0.3 seconds when the engine is cracking to start. Disconnect the A7 connector from the ECM before measuring the voltage.




OK

15.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FUSIBLE LINK BLOCK - ECM)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

15.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FUSIBLE LINK BLOCK - ECM)
a.

Disconnect the G57 and G60 ECU connectors.

B460088E01
3.083,1 3.5,1.25 0.417,0.25 5.25,1 5.667,1.25 0.417,0.25 4.75,3.458 5.167,3.708 0.417,0.25 3.792,1.354 3.906,1.802 false 6.229,1.344 6.458,1.344 false 4.271,3.479 5.125,2.833 false 0.281,2.354 1.167,2.729 0.885,0.375 10 false ST CUT Relay Terminal 0.104,0.177 2.323,0.635 2.219,0.458 10 false Component without relay connected: (Fusible Link Block) 2.885,0.104 4.802,0.542 1.917,0.438 10 false Front view of wire harness connector: (to Main body ECU) 5.115,0.115 7.01,0.531 1.896,0.417 10 false Front view of wire harness connector: (to Main body ECU) 3.844,1.813 4.5,2.073 0.656,0.26 10 false STR 3.156,1.031 3.813,1.292 0.656,0.26 10 false G57 5.323,1.042 5.979,1.302 0.656,0.26 10 false G60 6.49,1.26 7.146,1.521 0.656,0.26 10 false STR2 3.573,2.104 6.542,2.427 2.969,0.323 10 false Front view of wire harness connector: (to ECM) 4.854,3.49 5.51,3.75 0.656,0.26 10 false D1 3.958,3.49 4.615,3.75 0.656,0.26 10 false STAR


b.

Disconnect the D1 ECM connector.


c.

Remove the ST CUT relay from the fusible link block.


d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G60-6 (STR2) - D1-63 (STAR) Always Below 1 Ω
G60-6 (STR2) - ST CUT relay terminal-3
G57-8 (STR) - ST CUT relay terminal-5
G60-6 (STR2) - Body ground 10 kΩ or higher
G57-8 (STR) - Body ground Shift position is Except P or N 10 kΩ or higher




OK

16.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
B138018E31
0.125,0.115 2.813,0.458 2.688,0.344 10 false Component without harness connected: (Park/Neutral Position Switch)

Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
4 - 9 P Below 1 Ω
4 - 9 N Below 1 Ω
4 - 9 Except P and N 10 kΩ or higher




OK

17.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH

17.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the A7 ECM connector.

B460089E01
0.083,1.5 0.5,1.75 0.417,0.25 2.25,1.5 2.667,1.75 0.417,0.25 5.667,2.333 6.083,2.583 0.417,0.25 1.604,1.604 1.813,1.24 false 1.583,1.76 1.75,2.125 false 2.917,1.75 3.135,2.229 false 6.542,2.365 6.313,1.854 false 0.083,0.125 2.354,0.531 2.271,0.406 10 false Front view of wire harness connector: (to Park/Neutral Position Switch) 0.198,1.531 0.698,1.771 0.5,0.24 10 false D4 1.656,1.01 2.156,1.25 0.5,0.24 10 false D4-4 1.594,2.135 2.094,2.375 0.5,0.24 10 false D4-9 2.313,1.542 2.813,1.781 0.5,0.24 10 false G57 3.115,2.24 3.615,2.479 0.5,0.24 10 false STR 2.573,0.135 4.49,0.677 1.917,0.542 10 false Front view of wire harness connector: (to Main Body ECU) 4.979,0.135 6.573,0.698 1.594,0.563 10 false Front view of wire harness connector: (to ECM) 6.469,2.375 6.969,2.615 0.5,0.24 10 false STA 5.781,2.375 6.281,2.615 0.5,0.24 10 false A7


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G57-8 (STR) - D4-4 Always Below 1 Ω
G57-8 (STR) - Body ground Always 10 kΩ or higher
A7-48 (STA) - D4-9 Always Below 1 Ω
A7-48 (STA) - Body ground Always 10 kΩ or higher




OK

18.INSPECT RELAY (ST)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT RELAY (ST)
a.
B168632

Remove the ST relay from the engine room relay block No. 1.


b.

Measure the resistance according value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 5 When battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

19.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)

NG

REPLACE ST RELAY

19.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Remove the ST relay from the engine room relay block No. 1.

B460090E01
5.25,3.083 5.667,3.333 0.417,0.25 6.115,3.135 5.865,2.646 false 0.917,0.094 3.177,0.667 2.26,0.573 10 false Component without relay connected: (to Engine Room Relay Block No. 1) 2.948,2.688 3.552,3.073 0.604,0.385 10 false ST Relay Terminal 4.427,0.917 6.677,1.417 2.25,0.5 10 false Front view of wire harness connector: (to ECM) 6.052,3.167 6.677,3.458 0.625,0.292 10 false STA 5.365,3.115 5.99,3.406 0.625,0.292 10 false A7


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A7-48 (STA) - ST relay terminal-1 Always Below 1 Ω
A7-48 (STA) - Body ground 10 kΩ or higher




OK

20.INSPECT ENGINE ROOM RELAY BLOCK (ST RELAY VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT ENGINE ROOM RELAY BLOCK (ST RELAY VOLTAGE)
a.
B167662E01
0.313,0.023 2.594,0.370 2.281,0.347 10 Component without relay connected: (Engine Room Relay Block No. 1) 2.53,3.306 3.144,3.653 0.614,0.347 10 ST Relay Terminal

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
ST relay terminal-5 - Body ground Always 11 to 14 V
ST relay terminal-2 - Body ground Below 1 V




OK

21.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER - BATTERY, ST RELAY)

21.INSPECT STARTER ASSEMBLY

OK

22.READ VALUE USING INTELLIGENT TESTER (L CODE)

NG

REPAIR OR REPLACE STARTER ASSEMBLY

22.READ VALUE USING INTELLIGENT TESTER (L CODE)
a.

Reconnect the connectors.


b.

Connect the intelligent tester to the DLC3.

HINT:

When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.



c.

Turn the engine switch on (IG).

Entry & Start (Certification ECU):
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L Code Chk L code check / OK or NG OK: Normal
NG: Malfunction
Electrical key in the cabin

OK:

OK is displayed on the screen.


HINT:

If the result is not as specified, refer to PROBLEM SYMPTOMS TABLE of the electrical steering lock (steering wheel cannot be unlocked) (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>PROBLEM SYMPTOMS TABLE).

If the result is not as specified, there may be a malfunction with the steering lock ECU or the ID code box.




OK

23.READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST)

NG

GO TO ELECTRIC STEERING LOCK

23.READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST)
a.

Connect the intelligent tester to the DLC3.

HINT:

When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.



b.

Turn the engine switch on (IG)

Entry & Start (Certification ECU):
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Start Rqst Start request signal response / OK or NG OK: Received
NG: Not received
-

OK:

OK (received) and NG (not receive) appear on the screen.


HINT:

If the result is not as specified, there may be a malfunction with the certification ECU or the ID code box.




OK

24.READ VALUE USING INTELLIGENT TESTER (S CODE)

NG

REPLACE CERTIFICATION ECU

24.READ VALUE USING INTELLIGENT TESTER (S CODE)
a.

Connect the intelligent tester to the DLC3.

HINT:

When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.



b.

Turn the engine switch on (IG).

Entry & Start (Certification ECU):
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Chk S code check / OK or NG OK: Normal
OFF: Malfunction
-



OK

25.INSPECT ID CODE BOX

NG

26.REPLACE CERTIFICATION ECU
25.INSPECT ID CODE BOX
a.
B460081E01
1.5,0.833 1.917,1.083 0.417,0.25 1.479,2.052 1.479,1.677 false 0.094,0.073 2.521,0.635 2.427,0.563 10 false Component without harness connected: (ID Code Box) 1.583,0.875 2.021,1.146 0.438,0.271 10 false G20 1.323,2.073 1.76,2.344 0.438,0.271 10 false EFIO 0.177,4.125 0.615,4.396 0.438,0.271 10 false GND 2.958,3.885 3.396,4.156 0.438,0.271 10 false HI 2.948,4.135 3.344,4.375 0.396,0.24 10 false LOW

Check the input signal waveform.

i.

Connect an oscilloscope to terminal G20-6 (EFIO) and body ground.


ii.

Turn the engine switch on (IG).


iii.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 10 V/DIV., 100 ms./DIV.
Vehicle condition Engine switch on (IG)




OK

END

NG

REPLACE ID CODE BOX

26.REPLACE CERTIFICATION ECU
a.

Replace the certification ECU.


b.

Perform the registration procedures for the engine immobiliser system.


c.

Check if the engine can be started.

OK:

Engine starts normally.




OK

END (CERTIFICATION ECU IS DEFECTIVE)

NG

REPLACE ID CODE BOX