1.INSTALL SHIFT LEVER ASSEMBLY
Install the floor shift with the 4 bolts and screw.
for 12 mm bolt
Connect the 2 connectors.
33820B
2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.
| *a | Stopper |
| *b | Nut |
| *c | Push in |
Install the transmission control cable outer to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.
| *a | Shift Lever Retainer | *b | Spring |
| *c | Stopper | *d | Push in |
If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.
Install the cable end to the shift control unit.
Check that the lock piece is pulled up.
Install the cable end all the way to the base of the pin.
Push the lock piece into the adjuster case.
| *a | Push in |
Securely push in the lock piece until it locks.
55900A
3.INSTALL HEATER CONTROL AND ACCESSORY
55433B
4.INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL LOWER
55434B
5.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER
58533C
6.INSTALL FLOOR CARPET COVER CENTER RH
58534E
7.INSTALL FLOOR CARPET COVER CENTER LH
55432B
8.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER (w/ Knee Airbag)
55432B
9.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER (w/o Knee Airbag)
55606
10.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55447C
11.INSTALL NO. 1 SWITCH HOLE BASE
55474B
12.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH
62111C
13.INSTALL COWL SIDE TRIM BOARD RH
62112
14.INSTALL COWL SIDE TRIM BOARD LH
67913B
15.INSTALL FRONT DOOR SCUFF PLATE RH
67914B
16.INSTALL FRONT DOOR SCUFF PLATE LH
33504F
17.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
55550
18.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
55042B
19.INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
55660
20.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
55041B
21.INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
55650
22.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
55414A
23.INSTALL INSTRUMENT CLUSTER FINISH PANEL END (w/o Navigation System)
24.INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
55420A
25.INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER ASSEMBLY
45286
26.INSTALL STEERING COLUMN COVER
84306
27. POSITION SPIRAL CABLE
45100
28.INSTALL STEERING WHEEL ASSEMBLY
45130
29.INSTALL STEERING PAD ASSEMBLY
45187
30.INSTALL NO. 3 STEERING WHEEL LOWER COVER
45186
31.INSTALL NO. 2 STEERING WHEEL LOWER COVER
28800
32.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See Page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
45130
33.INSPECT STEERING PAD ASSEMBLY
34. SRS WARNING LIGHT CHECK
Check the SRS WARNING LIGHT (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
45100
35.INSPECT STEERING WHEEL ASSEMBLY
36. REPLACED OPERATION (w/ Navigation System)
for G-BOOK System: (See page Audio / Visual / Telematics>G-BOOK>G-BOOK SYSTEM>REGISTRATION)
for Parking Assist Monitor System: (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION)