The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the camshaft removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
51406A
3.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)
52618
4.REMOVE LOWER FRONT BUMPER ABSORBER
51405A
5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
6.DRAIN ENGINE COOLANT
85110
7.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
55701J
8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
53106B
9.REMOVE RADIATOR COVER SUB-ASSEMBLY
17751
10.REMOVE NO. 1 AIR CLEANER INLET
44360
11.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
17030
12.REMOVE AIR HOSE ASSEMBLY
16470
13.REMOVE RADIATOR COVER SUB-ASSEMBLY
16571C
14.REMOVE NO. 1 RADIATOR HOSE
88359
15.REMOVE VISCOUS HEATER V BELT (w/ Viscous Heater)
16711
16.REMOVE FAN SHROUD
16572D
17.REMOVE NO. 2 RADIATOR HOSE
18.REMOVE FRONT BUMPER
for Wagon:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Wagon)>REMOVAL
except Wagon:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (except Wagon)>REMOVAL
53510
19.REMOVE HOOD LOCK ASSEMBLY
17311B
20.REMOVE NO. 1 AIR INLET DUCT
88590
21.REMOVE BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)
for LH Side:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER FAN>REMOVAL
for RH Side:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER FAN>REMOVAL
53209B
22.REMOVE HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY
16546
23.REMOVE RADIATOR PROTECTOR (w/o Air Conditioning System)
53286F
24.REMOVE RADIATOR SIDE AIR SEAL LH (for Wagon)
53285N
25.REMOVE RADIATOR SIDE AIR SEAL RH (for Wagon)
51466
26.REMOVE UPPER RADIATOR SUPPORT BRACE LH (for Wagon)
51465
27.REMOVE UPPER RADIATOR SUPPORT BRACE RH (for Wagon)
86520
28.REMOVE LOW PITCHED HORN ASSEMBLY
Click hereVehicle Exterior>HORN>HORN>REMOVAL
86510
29.REMOVE HIGH PITCHED HORN ASSEMBLY (for 2-piece Type)
Click hereVehicle Exterior>HORN>HORN>REMOVAL
53205
30.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
32921D
31.DISCONNECT OIL COOLER INLET HOSE (for Automatic Transmission)
32922A
32.DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)
16400
33.REMOVE RADIATOR ASSEMBLY
12601B
34.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Cover)
25760F
35.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY
17303T
36.REMOVE AIR PIPE SUB-ASSEMBLY
26100G
37.REMOVE DIESEL THROTTLE BODY ASSEMBLY
87209
38.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Heater)
16278
39.REMOVE NO. 2 WATER BY-PASS PIPE
89421C
40.REMOVE DIESEL TURBO PRESSURE SENSOR
23265C
41.REMOVE GAS FILTER
12632
42.REMOVE NO. 2 ENGINE COVER BRACKET
23941
43.DISCONNECT NO. 1 FUEL FILTER PROTECTOR
82121
44.DISCONNECT ENGINE WIRE
25625
45.REMOVE EGR VALVE BRACKET (w/ EGR System)
25612
46.REMOVE NO. 2 EGR PIPE (w/ EGR System)
25800
47.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System)
25624
48.REMOVE EGR VALVE ADAPTER SUB-ASSEMBLY
49.REMOVE WIRING HARNESS CLAMP BRACKET
50.REMOVE HARNESS BRACKET
23760
51.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY
52.REMOVE NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23670
53.REMOVE INJECTOR ASSEMBLY
23682
54.REMOVE NOZZLE HOLDER GASKET
11401Q
55.REMOVE CAMSHAFT POSITION SENSOR
11201
56.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
57.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *a | Timing Mark |
| *b | Paint Mark |
Align the timing mark of the crankshaft pulley and timing chain cover by rotating the crankshaft clockwise.
Make sure that the timing mark of the camshaft timing sprocket is at the top.
If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).
Place paint marks on the No. 2 chain sub-assembly.
58.REMOVE NO. 3 CAMSHAFT BEARING CAP
Remove the 2 bolts and No. 3 camshaft bearing cap from the cylinder head sub-assembly.
29300
59.REMOVE VACUUM PUMP ASSEMBLY
11382C
60.REMOVE CAMSHAFT OIL SEAL RETAINER
13566B
61.REMOVE TIMING CHAIN GUIDE
Remove the bolt and timing chain guide from the cylinder head sub-assembly.
62.REMOVE CAMSHAFT
Remove the oil pump relief valve plug and gasket from the timing chain cover.
| *a | Stopper Plate |
| *b | Pin |
Insert a pin into the stopper plate hole of the No. 2 chain tensioner assembly and lock the No. 2 chain tensioner assembly.
| *1 | No. 1 Camshaft |
| *2 | No. 2 Camshaft |
Hold the hexagonal portion of the camshaft with a wrench and loosen the 2 bolts from the No. 1 camshaft and No. 2 camshaft.
Be careful not to damage the cylinder head sub-assembly with the wrench.
Using several steps, remove the 20 bolts, No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps from the cylinder head sub-assembly.
Raise the No. 1 camshaft and remove the bolt from the No. 1 camshaft.
Raise the No. 2 camshaft and remove the bolt from the No. 2 camshaft.
Remove the No. 2 camshaft from the camshaft timing sprocket.
Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.
Remove the No. 1 camshaft from the camshaft timing sprocket.
Remove the camshaft timing sprocket from the No. 2 chain sub-assembly.
Suspend the No. 2 chain sub-assembly with a string or equivalent.
Be careful not to drop the No. 2 chain sub-assembly inside the timing chain cover assembly.