Home › Engine / Hybrid System › 1GD-FTV (LUBRICATION) › OIL PUMP › 2019.06–2020.05
RM35X0E _51 Engine / Hybrid System _079221 1GD-FTV LUBRICATION _0386560 OIL PUMP A

1GD-FTV LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the timing chain case assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of ECM
·

Learning Values Save

·

Learning Values Write

·

Perform Vehicle Identification Number (VIN) or frame number registration


DTC P063051 is stored
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)

·

w/ Exhaust Gas Temperature Sensor for EGR

(Click here)


ECU communication ID registration Engine start function See the Service Bulletin for the registration method.
for RC60J:

Performing iMT installation information reset


·

iMT system

·

DTCs are output


(Click here)
Replacement of engine assembly Clear crank time compensation data Engine starting
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)

·

w/ Exhaust Gas Temperature Sensor for EGR

(Click here)


·

Input injector compensation code

·

Pilot quantity learning


Engine starting
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)


Replacement of crankshaft position sensor plate Clear crank time compensation data Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)

·

w/ Exhaust Gas Temperature Sensor for EGR

(Click here)


w/ DPF, w/ Urea SCR System:

Replacement of air fuel ratio sensor


Clear A/F sensor learning value data -
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ Exhaust Gas Temperature Sensor for EGR

(Click here)


w/ DPF, w/ Urea SCR System:

Replacement of exhaust manifold converter sub-assembly


Clear DPF thermal deterioration data -
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ Exhaust Gas Temperature Sensor for EGR

(Click here)


Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)


·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly

·

Replacement of turbocharger nozzle vane control actuator


Perform initialization -
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)

·

w/ Exhaust Gas Temperature Sensor for EGR

(Click here)


w/ Stop and Start System:

Replacement of starter assembly

NOTICE:

When the starter assembly is replaced, "STARTER relay" and "STARTER NO.2 relay" must be also replaced.



Clear the number of starter operations Stop and start system (Click here)
w/ Stop and Start System:
·

Replacement of flywheel sub-assembly (for Automatic Transmission)

·

Replacement of flywheel with damper assembly (for Manual Transmission)


Total number of engine starts reset
for AE60E:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AE60E:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc. Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative when not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative when not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 82121 3.REMOVE ENGINE WIRE

Hide 26100G 4.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 89481B 6.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 7.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 12631A 11.REMOVE ENGINE COVER BRACKET

Hide 89425D 15.REMOVE NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 16206B 17.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 16206B 18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)

Hide 25601 20.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)

Hide 25601 21.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)

Hide 25804 22.REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler)

Hide 16209 23.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25800 24.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)

Hide 25.REMOVE EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 25624 26.REMOVE EGR VALVE ADAPTER (w/o EGR System)

Hide 11409 27.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 29.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 31.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 32.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 33.REMOVE NO. 2 FUEL HOSE

Hide 23271H 34.REMOVE NO. 1 FUEL HOSE

Hide 23804D 35.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

Hide 23804D 36.REMOVE NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23815D 37.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804C 38.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 39.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 41.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 43.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 44.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23701 45.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 88320 47.REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 88431 48.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 16632B 49.REMOVE NO. 2 IDLER PULLEY BRACKET (w/o Air Conditioning System)

Hide 12229 50.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 16282 51.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)

Hide 16281 52.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

Hide 23295D 53.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 89467B 54.REMOVE AIR FUEL RATIO SENSOR (w/o Exhaust Gas Temperature Sensor for EGR)

Hide 17167 55.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)

Hide 17167 56.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o DPF)

Hide 17271 57.REMOVE NO. 1 TURBO INSULATOR (w/ DPF)

Hide 17271 58.REMOVE NO. 1 TURBO INSULATOR (w/o DPF)

Hide 89463C 59.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 60.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/ DPF)

Hide 61.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/o DPF)

Hide 63.REMOVE EXHAUST PIPE SUPPORT STAY (w/o DPF)

Hide 25051 64.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)

Hide 17291 65.REMOVE TURBINE OUTLET ELBOW (w/o EGR Cooler)

Hide 89463C 66.REMOVE NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 12261 67.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 69.REMOVE WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)

Hide 16268 70.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 16284 71.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 87101 72.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

Hide 15407 75.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 16207 77.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16304 78.REMOVE WATER OUTLET SUB-ASSEMBLY

Hide 16331A 80.REMOVE THERMOSTAT

Hide 16603 81.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A339577

Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.


Hide 16620 82.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A339579

Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.


Hide 88451B 83.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 13496 84.REMOVE CRANKSHAFT PULLEY COVER (for Automatic Transmission)

Hide 13407 85.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY (for Manual Transmission)

Hide 13471 86.REMOVE CRANKSHAFT PULLEY (for Automatic Transmission)

Hide 16575C 87.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

Hide 12501 89.REMOVE GENERATOR BRACKET SUB-ASSEMBLY

Hide 23670 90.REMOVE INJECTOR ASSEMBLY

Hide 23682 91.REMOVE NOZZLE HOLDER GASKET

Hide 11401G 92.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 93.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A339580C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Nozzle Holder Clamp Seat


Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.


b.
A339581C01
2.219,0.563 2.427,0.292 2.427,0.292 2.552,0.292 true 0.323,1.802 0.469,1.802 0.469,1.802 0.708,1.25 true 0.885,1.385 1.063,1.26 1.063,1.26 1.188,1.26 true 0.771,0.594 1.031,0.365 1.031,0.365 1.156,0.365 true 2.615,0.198 2.813,0.385 0.198,0.188 10 true *1 0.115,1.719 0.292,1.885 0.177,0.167 10 false *2 1.229,1.167 1.417,1.333 0.188,0.167 10 true *3 1.229,0.281 1.417,0.448 0.188,0.167 10 false *3
*1 Cylinder Head Cover Gasket
*2 No. 2 Cylinder Head Cover Gasket
*3 Camshaft Bearing Cap Oil Hole Gasket


Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.


Hide 89491 94.REMOVE ENGINE OIL LEVEL SENSOR

Hide 12101 95.REMOVE OIL PAN SUB-ASSEMBLY

a.
A339600C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 23 bolts and 2 nuts.


b.
A303108

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.

·

Be careful not to damage the cylinder block sub-assembly flange.




Hide 16100 96.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 97.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11324 98.REMOVE TIMING CHAIN COVER PLATE

Hide 22815A 100.REMOVE INJECTION PUMP INSULATOR

Hide 11302 101.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A339584

Remove the 20 bolts from the timing chain cover sub-assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.

A339585C01
6.156,0.719 6.49,0.177 6.49,0.177 6.625,0.177 true 5.604,1.927 6.094,2.396 6.094,2.396 6.229,2.396 true 0.406,1.156 0.552,1.156 0.552,1.156 1.052,0.708 true 0.198,1.073 0.385,1.25 0.188,0.177 10 false *a 6.302,2.313 6.51,2.479 0.208,0.167 10 false *a 6.677,0.083 6.885,0.26 0.208,0.177 10 false *a
*a Protective Tape - -


NOTICE:

Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.



c.
A339592

Remove the timing chain case gasket from the timing chain case assembly.


Hide 11303A 102.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A339586C01
0.583,1.271 1.271,1.271 true 1.417,0.917 2.167,0.354 2.167,0.354 2.375,0.354 true 2.448,0.271 2.656,0.458 0.208,0.188 10 false *a 0.354,1.188 0.563,1.375 0.208,0.188 10 false *b
*a Protective Tape
*b Wooden Block


Using a screwdriver and wooden block, pull out the front crankshaft oil seal.

NOTICE:

Do not damage the surface of the front crankshaft oil seal press fit hole.



Hide 103.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR

a.
A339596

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.3 mm (0.000787 to 0.0118 in.)


Maximum gear backlash:

0.42 mm (0.0165 in.)


If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.


Hide 13519 104.REMOVE OIL PUMP DRIVE GEAR

a.
A339595

Remove the oil pump drive gear from the crankshaft.


Hide 13560A 105.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 11991A 106.REMOVE NO. 1 BALANCESHAFT THRUST PLATE

Hide 107.REMOVE BALANCESHAFT TIMING SPROCKET, BALANCESHAFT GEAR SUB-ASSEMBLY WITH NO. 3 CHAIN SUB-ASSEMBLY

Hide 13550 109.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 110.REMOVE NO. 2 CHAIN TENSIONER SLIPPER

Hide 13562 111.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13507 112.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 13540 113.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 114.REMOVE NO. 1 CHAIN TENSIONER SLIPPER

Hide 13561 115.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 116.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

Hide 13523 117.REMOVE CAMSHAFT TIMING SPROCKET

Hide 11310 118.REMOVE TIMING CHAIN CASE ASSEMBLY

a.
A339590

Remove the 15 bolts from the timing chain case assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.

A339591C01
0.729,0.646 0.865,0.646 0.865,0.646 1.167,1.24 true 5.823,2.094 6.323,2.479 6.323,2.479 6.469,2.479 true 6.323,0.552 6.656,1.219 6.656,1.219 6.802,1.219 true 0.479,0.552 0.698,0.74 0.219,0.188 10 false *a 6.521,2.385 6.74,2.573 0.219,0.188 10 false *a 6.854,1.125 7.052,1.292 0.198,0.167 10 false *a
*a Protective Tape - -


NOTICE:

Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.



c.
A339593

Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.


d.
A388469

Remove the gasket from the timing chain case assembly.