DTC C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1271 C1272 | Detected only during Test Mode. |
|
| C1275 C1276 | Detected only during Test Mode. | Speed sensor rotor |
| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Speed Open | FR speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
| FL Speed Open | FL speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
| Result | Proceed to |
| There are momentary interruptions | A |
| There are no momentary interruptions | B |
| There is a constant open circuit | C |
|
| ||||
|
| ||||
| A | |
| 2.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU and the front speed sensor (Click here).
Check that there are no momentary interruptions.
| NEXT | |
| 3.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||
| 4.READ VALUE ON TECHSTREAM (FRONT SPEED SENSOR) |
Turn the ignition switch off.
Connect Techstream to the DLC3.
Start the engine.
Select the Data List mode on Techstream (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed | Similar speed as indicated on speedometer |
| FL Wheel Speed | FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed | Similar speed as indicated on speedometer |
Check that there is no difference between the speed value output from the speed sensor displayed on Techstream and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 5.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK FRONT SPEED SENSOR INSTALLATION |
![]() |
Turn the ignition switch off.
Check the speed sensor installation.
|
| ||||
| OK | |
| 7.CHECK FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
|
| ||||
| OK | |
| 8.CHECK FRONT SPEED SENSOR ROTOR |
Remove the front speed sensor rotor (Click here).
Check the speed sensor rotor.
|
| ||||
| OK | |
| 9.INSPECT FRONT SPEED SENSOR |
![]() |
Install the front speed sensor and the front speed sensor rotor.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (FR+) - Body ground | Always | 10 kΩ or higher |
| 1 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 2 (FL+) - Body ground | Always | 10 kΩ or higher |
| 1 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
![]() |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-7 (FR+) - A29-2 (FR+) | Always | Below 1 Ω |
| A24-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| A24-6 (FR-) - A29-1 (FR-) | Always | Below 1 Ω |
| A24-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A24-19 (FL+) - A12-2 (FL+) | Always | Below 1 Ω |
| A24-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A24-18 (FL-) - A12-1 (FL-) | Always | Below 1 Ω |
| A24-18 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.INSPECT SKID CONTROL ECU (SENSOR INPUT) |
![]() |
Reconnect the skid control ECU connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A29-2 (FR+) - Body ground | Ignition switch on (IG) | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| A12-2 (FL+) - Body ground | Ignition switch on (IG) | 8 to 14 V |
|
| ||||
| OK | |
| 12.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||
| 13.REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
| NEXT | |
| 14.PERFORM TEST MODE (SIGNAL CHECK) |
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||
| 15.REPLACE FRONT SPEED SENSOR ROTOR |
Turn the ignition switch off.
Remove the front drive shaft assembly (Click here).
Replace the front drive outboard joint shaft assembly (front speed sensor rotor) (Click here).
| NEXT | |
| 16.PERFORM TEST MODE (SIGNAL CHECK) |
Install the front drive shaft assembly.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||