Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY › from 2016.11
RM3160E _52 Drivetrain _019687 AXLE AND DIFFERENTIAL _0109983 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

If installing a new rear differential carrier assembly, remove the 2 differential side seal caps before installing the rear drive shaft assembly.


PROCEDURE

Hide 52380 1.TEMPORARILY INSTALL NO. 1 REAR DIFFERENTIAL SUPPORT

a.
C295943N01
0.354,0.208 0.552,0.406 0.198,0.198 10 false A 2.802,0.948 3,1.146 0.198,0.198 10 true A

Temporarily install the No. 1 rear differential support to the rear differential carrier assembly with 2 new bolts and 2 new nuts.

NOTICE:
·

Be sure to install the No. 1 rear differential support facing the direction shown in the illustration.

·

Be sure to install the tab of each nut to the position (A) shown in the illustration.



HINT:

The nuts have tabs to prevent them from rotating.



Hide 41653 2.INSTALL UPPER REAR DIFFERENTIAL MOUNT STOPPER

C295935

a.

Install the 2 upper rear differential mount stoppers to the No. 1 rear differential support.

NOTICE:

Keep the upper rear differential mount stoppers free of oil and foreign matter.



Hide 52391B 3.INSTALL DIFFERENTIAL SUPPORT

a.
C201217N02
0.979,0.385 1.229,0.573 0.25,0.188 10 false A

Install the differential support to the rear differential carrier assembly with 3 new bolts.

Torque:
166.7 N*m (1700 kgf*cm, 123 ft.*lbf)

NOTICE:

Tighten the bolt (A) shown in the illustration first.



Hide 4.TEMPORARILY INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

NOTICE:
·

Do not damage the contact surface when installing the rear differential carrier assembly with differential support.

·

The remaining oil may leak out when installing the rear differential carrier assembly with differential support.

·

Securely support the rear differential carrier assembly with differential support while performing this step to avoid excessively tilting or dropping the rear differential carrier assembly with differential support.

·

Install the bolts and nuts with the rear differential carrier assembly with differential support secured.



a.
C295933C01
0.76,2.958 1.281,2.958 true 1.635,2.292 1.635,2.531 1.635,2.531 2.448,2.531 true 2.198,2.292 2.198,2.531 true 0.313,2.052 0.51,2.052 0.51,2.052 0.51,2.385 true 3.052,1.063 2.781,1.063 2.781,1.063 2.781,1.677 true 2.198,2.688 2.198,3.021 true 0.167,1.958 0.479,2.156 0.313,0.198 10 false *1 3.052,0.969 3.25,1.177 0.198,0.208 10 false *1 2.458,2.427 2.656,2.635 0.198,0.208 10 false *a 1.302,2.865 1.5,3.073 0.198,0.208 10 false *a 2.135,3.042 2.448,3.24 0.313,0.198 10 false *b 0.188,2.719 0.5,2.917 0.313,0.198 10 false A 2.865,1.958 3.177,2.156 0.313,0.198 10 false A 0.51,1.302 0.823,1.5 0.313,0.198 10 false B 1.021,1.031 1.177,1.24 0.156,0.208 10 true B
*1 Lower Rear Differential Mount Stopper
*a Attachment
*b Engine Lifter


Support the rear differential carrier assembly with differential support with an engine lifter using 3 attachments or equivalent tools as shown in the illustration.


b.

Temporarily install the rear differential carrier assembly with differential support to the front side of the rear suspension member sub-assembly with the 2 lower rear differential mount stoppers, 2 new bolts (A) and 2 new nuts.

NOTICE:
·

Be sure to install the lower rear differential mount stoppers with the convex side facing upward.

·

Keep the bolt (A) and lower rear differential mount stoppers free of oil and foreign matter.



HINT:

The nuts have tabs to prevent them from rotating.



c.

Temporarily install the rear differential carrier assembly with differential support to the rear side of the rear suspension member sub-assembly with the 2 new bolts (B).


d.
C295934C01
2.313,2.385 2.313,2.688 true 1.073,2.458 1.323,2.156 true 2.229,2.688 2.542,2.885 0.313,0.198 10 false *1 1.333,2.063 1.521,2.292 0.188,0.229 10 false *1 1.385,2.656 1.573,2.885 0.188,0.229 10 false *2 2.74,2.052 2.927,2.281 0.188,0.229 10 false *2 0.521,2.531 0.688,2.74 0.167,0.208 10 true *a
*1 Vacuum Hose
*2 Clamp
*a Connector


Connect the vacuum hose to the 2 clamps, connect the connector, and install the clamp to the connector bracket.


Hide 5.FULLY INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

NOTICE:

Do not tighten the bolts with the inner cylinder or rear differential mount cushion tilted.


a.
C295944

Tighten the 2 bolts.

Torque:
95.1 N*m (970 kgf*cm, 70 ft.*lbf)


b.
C295932

Tighten the 2 bolts.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)

HINT:
·

Tighten the bolts only if the No. 1 rear differential support has been removed from the rear differential carrier assembly.

·

Lower the engine lifter to the extent that the bolts can still be tightened.




c.
C295945

Tighten the 2 bolts.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


d.

Lower the engine lifter.


e.
C204695C01
2.927,0.979 2.927,1.115 false 2.875,1.125 3.104,1.333 0.229,0.208 10 false *a
*a Paint Mark


Connect the vacuum hose to the electro magnetic control coupling sub-assembly.

NOTICE:

Connect the vacuum hose until it reaches the paint mark.



Hide 48812 6.INSTALL REAR STABILIZER BAR

Hide 48802 7.INSTALL STABILIZER LINK SUB-ASSEMBLY LH

Hide 48802 8.INSTALL STABILIZER LINK SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side and LH side.

Click hereSuspension>REAR SUSPENSION>REAR COIL SPRING>INSTALLATION


Hide 17430 9.INSTALL TAIL EXHAUST PIPE ASSEMBLY

Hide 37100 10.TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 37100 11.FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 42305 13.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH

a.
C295952C01
1.115,1.969 1.448,1.969 true 2.26,2.031 2.792,2.219 true 2.313,2.396 2.844,2.583 true 2.823,2.167 3.135,2.323 0.313,0.156 10 false *a 2.875,2.552 3.188,2.708 0.313,0.156 10 false *b 1.479,1.885 1.677,2.083 0.198,0.198 10 true *c
*a Wooden Block
*b Jack
*c Spacer
V100135

Bolt
V100136

Nut


Using a jack and wooden block, jack up the rear No. 2 suspension arm assembly LH to replicate standard vehicle height conditions.

CAUTION:

Do not jack up the rear No. 2 suspension arm assembly LH too high as the vehicle may fall.



b.

Remove the 4 bolts, 3 nuts and spacer to remove the rear axle carrier sub-assembly LH from the rear No. 1 suspension arm assembly LH, rear No. 2 suspension arm assembly LH, rear upper control arm assembly LH and rear lower shock absorber bracket sub-assembly LH.


Hide 42360A 14.INSTALL REAR DRIVE SHAFT SNAP RING LH

Hide 42340B 15.INSTALL REAR DRIVE SHAFT ASSEMBLY LH

Hide 42304 16.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side and LH side.


Hide 42360A 17.INSTALL REAR DRIVE SHAFT SNAP RING RH

HINT:

Use the same procedure for the RH side and LH side.

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>REAR DRIVE SHAFT ASSEMBLY(for AWD)>INSTALLATION


Hide 42330 18.INSTALL REAR DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure for the RH side and LH side.

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>REAR DRIVE SHAFT ASSEMBLY(for AWD)>INSTALLATION


Hide 19.ADD DIFFERENTIAL OIL

a.

When reusing the rear differential carrier assembly:

i.
C201207

Using a 10 mm hexagon wrench, install a new gasket and the rear differential drain plug.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)




b.

When using a new rear differential carrier assembly:

i.
C201206

Using a 10 mm hexagon wrench, remove the differential inspection plug and gasket.




Hide 41110X 21.INSTALL DIFFERENTIAL INSPECTION PLUG

Hide 22. INSPECT FOR DIFFERENTIAL OIL LEAK

Hide 42305 23.INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH

Hide 42304 24.INSTALL REAR AXLE CARRIER SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side and LH side.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE CARRIER(for AWD)>INSTALLATION


Hide 51569F 27.INSTALL PROPELLER SHAFT GUARD (for Front Side)

Hide 51569G 28.INSTALL PROPELLER SHAFT GUARD (for Rear Side)

Hide 29.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 58167A 30.INSTALL FRONT CENTER FLOOR COVER

Hide 51442 32.INSTALL NO. 2 ENGINE UNDER COVER