Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086906 A25A-FXS, A25B-FXS ENGINE MECHANICAL _0418981 CYLINDER HEAD GASKET A

A25A-FXS, A25B-FXS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*3: If the vehicle height has changed due to suspension or tire replacement

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC is output (Click here)
·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD:(Click here)
for 4WD/AWD:(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Replacement of front bumper assembly*2
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Replacement of front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Replacement of rear television camera assembly

·

Replacement of side television camera assembly LH or outer rear view mirror assembly LH

·

Replacement of side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment Perform "Calibration".
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 88370 3.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

Hide 16207 4.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16260 5.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

Hide 17167 6.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17141 8.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 22030 9.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25601 12.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 17177 18.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23801P 20.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 21.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 11452 31.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15250 32.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 33.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 34.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 35.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 36.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 16261G 38.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
A411195

Slide the clip and disconnect the No. 1 water by-pass hose from the cylinder block sub-assembly.


Hide 16264D 39.DISCONNECT NO. 2 WATER BY-PASS HOSE

a.
A411196

Slide the clip and disconnect the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.


Hide 11201 43.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11320B 46.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 47.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 13507A 49.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

Hide 13050 50.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 52.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13561 54.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 55.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11103 58.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13801 62.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 63.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11115 66.REMOVE CYLINDER HEAD GASKET

A403803

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.