Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420003 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  INSTALLATION  


PROCEDURE

Hide 821H1 1.INSTALL FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

for 4WD/AWD:

i.
A455864C01
2.594,3.104 2.208,3.104 2.208,3.104 1.896,2.708 true 2.646,3 2.958,3.198 0.313,0.198 10 false *a
*a Waterproof Seal


Install the HV floor under wire to the rear traction motor with transaxle assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Make sure that the connector is fully engaged.

·

Do not damage the terminals, interlock connector or rear traction motor with transaxle assembly during installation.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not allow any foreign matter or water to enter the rear traction motor with transaxle assembly.

·

Although the connector may feel loose, this is not due to a malfunction.




ii.
A455863

Engage the clamp.


iii.
A455862

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iv.

Install a new clamp.



b.
A455865C01
2.802,1.729 2.875,1.552 2.875,1.552 2.99,1.552 true 3.01,1.469 3.167,1.625 0.156,0.156 10 true *a
*a Grommet


Install a new clamp.


c.

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Insert the HV floor under wire into the floor panel hole and engage the grommet.


e.
A455868

Insert the HV floor under wire into the floor panel hole and engage the grommet.


f.
A455861

Install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.
A455866

Install a new clamp.


h.

Install the 3 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


i.
A455867

Install the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


j.

Install a new clamp.


k.
A455869

Install 2 new clamps.


l.

Install the bolt and 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


m.
A455872

Install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


n.
A455871

Connect the engine room main wire to the HV floor under wire with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


o.

Engage the 2 claws.


p.
A455870

Engage the guide and 2 claws to install the No. 1 terminal cap.


q.
A455875

Install the 2 nuts and bolt to connect the air conditioning tube assembly.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


r.
A455874

Install the nut and connect the transmission control cable assembly.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 58151 2.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator with the 3 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 58043 3.INSTALL REAR MAIN MUFFLER HEAT INSULATOR SUB-ASSEMBLY

a.

Install the rear main muffler heat insulator sub-assembly with the 3 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 17573A 4.INSTALL NO. 3 EXHAUST PIPE SUPPORT BRACKET

a.

Install the No. 3 exhaust pipe support bracket with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 17574 5.INSTALL NO. 4 EXHAUST PIPE SUPPORT BRACKET

a.

Install the No. 4 exhaust pipe support bracket with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 58720B 6.INSTALL ENGINE SERVICE COVER ASSEMBLY

a.

Install the engine service cover assembly with the 3 nuts and clip.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 77001A 8.INSTALL FUEL TANK SUB-ASSEMBLY

Hide G92QC 12.INSTALL NO. 10 HV BATTERY SHIELD PANEL

Hide 58556C 13.INSTALL REAR FLOOR SILENCER

Hide 58510D 14.INSTALL FRONT FLOOR CARPET ASSEMBLY

Hide 821H1 15.CONNECT FLOOR UNDER WIRE

a.
A455860

Install the HV under floor wire with the nut.

Torque:
7.55 N*m (77 kgf*cm, 67 in.*lbf)


b.

Engage the 2 clamps.


Hide 64730B 16.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

Hide 66311 17.INSTALL ROPE HOOK (for RH Side)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 64725F 18.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 64974 19.INSTALL DECK TRIM POCKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 88625T 20.INSTALL COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR

Hide 73560 21.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>REAR NO. 2 SEAT OUTER BELT ASSEMBLY>INSTALLATION


Hide 64714H 22.INSTALL NO. 1 DECK SIDE TRIM COVER

HINT:

Use the same procedure as for the No. 2 deck side trim cover.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 73360D 23.CONNECT REAR SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>REAR NO. 1 SEAT OUTER BELT ASSEMBLY>INSTALLATION


Hide 64712F 24.INSTALL FRONT DECK SIDE TRIM COVER RH

Hide 25.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 82111 29.CONNECT ENGINE ROOM MAIN WIRE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.

Connect the inverter with converter assembly connector and move the lock lever to lock them.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connectors.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.




Hide 31.PERFORM INITIALIZATION