The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
1.REMOVE REAR WHEEL
17430
2.REMOVE TAIL EXHAUST PIPE ASSEMBLY
37100
3.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)
48738
4.REMOVE REAR SUSPENSION ARM COVER LH
48737
5.REMOVE REAR SUSPENSION ARM COVER RH
Perform the same procedure as for the LH side.
42312B
6.REMOVE REAR AXLE SHAFT NUT LH (for 4WD/AWD)
42311N
7.REMOVE REAR AXLE SHAFT NUT RH (for 4WD/AWD)
Perform the same procedure as for the LH side.
47319F
8.SEPARATE REAR FLEXIBLE HOSE LH
Remove the bolt and separate the rear flexible hose LH from the rear upper control arm assembly LH.
47318F
9.SEPARATE REAR FLEXIBLE HOSE RH
Perform the same procedure as for the LH side.
890C0A
10.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for 4WD/AWD)
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear skid control sensor.
Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.
Be careful not to damage the rear skid control sensor or connector cover.
890C0
11.DISCONNECT NO. 1 PARKING BRAKE WIRE ASSEMBLY (for 4WD/AWD)
Perform the same procedure as for the LH side.
89544E
12.REMOVE REAR SKID CONTROL SENSOR LH (for 4WD/AWD)
89544D
13.REMOVE REAR SKID CONTROL SENSOR RH (for 4WD/AWD)
Perform the same procedure as for the LH side.
14.REMOVE REAR STABILIZER LINK ASSEMBLY LH
15.REMOVE REAR STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
48812
16.REMOVE REAR STABILIZER BAR
48835
17.REMOVE REAR LOWER STABILIZER BRACKET
48231B
18.REMOVE REAR COIL SPRING LH
48231A
19.REMOVE REAR COIL SPRING RH
Perform the same procedure as for the LH side.
48258C
20.REMOVE REAR LOWER COIL SPRING INSULATOR LH
48258B
21.REMOVE REAR LOWER COIL SPRING INSULATOR RH
Perform the same procedure as for the LH side.
48740F
22.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
48730F
23.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
24.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
25.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48790
26.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH
Remove the bolt and nut and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
48770A
27.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH
Use the same procedure as for the LH side.
28.DRAIN DIFFERENTIAL OIL (for 4WD/AWD)
for Dynamic Torque Control AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT
for Dynamic Torque Vectoring AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT
42340B
29.REMOVE REAR DRIVE SHAFT ASSEMBLY LH (for 4WD/AWD)
42330
30.REMOVE REAR DRIVE SHAFT ASSEMBLY RH (for 4WD/AWD)
Use the same procedure as for the LH side.
42341C
31.REMOVE REAR DRIVE SHAFT LH SNAP RING (for 4WD/AWD)
42341B
32.REMOVE REAR DRIVE SHAFT RH SNAP RING (for 4WD/AWD)
Use the same procedure as for the LH side.
41110
33.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Control AWD)
41110
34.REMOVE TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Vectoring AWD)
41651
35.REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION (for 4WD/AWD)
82164
36.SEPARATE FRAME WIRE (for 4WD/AWD)
Remove the bolt and disengage the clamp to separate the frame wire from the rear suspension member sub-assembly.
51206A
37.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY
| *a | Engine Lifter |
| *b | Attachment |
| *c | Wooden Block |
|
Attachment and Wooden Block Placement Location |
Using an engine lifter, 2 attachments and 2 wooden blocks or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.
Remove the 4 bolts, 2 nuts, 2 rear lower suspension braces, rear lower suspension member stopper LH and rear lower suspension member stopper RH.
Slowly lower the rear suspension member sub-assembly.
When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.
52272
38.REMOVE REAR SUSPENSION MEMBER UPPER STOPPER
Remove the 2 rear suspension member upper stoppers from the rear suspension member sub-assembly.
52278A
39.REMOVE REAR SUSPENSION MEMBER LOWER STOPPER RETAINER
Remove the 2 rear suspension member lower stopper retainers from the rear suspension member sub-assembly.
48790
40.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH
48770A
41.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
52271D
42.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)
| *a | Bend Portion |
Using a chisel and hammer, bend the 2 portions of the rear suspension member front body mounting cushion rib.
Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
| *b | Turn |
Using SST, remove the rear suspension member front body mounting cushion while applying lubricant into the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.
Set the claws of SST onto the rear suspension member sub-assembly securely as shown in the illustration.
Tighten SST slowly and evenly.
Be careful as the rear suspension member front body mounting cushion may fly out.
The rear suspension member front body mounting cushion cannot be reused.
Remove SST and the rear suspension member front body mounting cushion (LH Side) from the rear suspension member sub-assembly.
52271D
43.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)
Perform the same procedure as for the LH side.
52276A
44.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH
| *a | Bend Portion |
Using a chisel and hammer, bend the 2 portions of the rear suspension member rear body mount cushion LH rib.
Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
| *b | Turn |
Using SST, remove the rear suspension member rear body mount cushion LH while applying lubricant into the clearance between the rear suspension member rear body mount cushion LH and the rear suspension member sub-assembly.
Set the claws of SST onto the rear suspension member sub-assembly securely as shown in the illustration.
Tighten SST slowly and evenly.
Be careful as the rear suspension member rear body mount cushion LH may fly out.
The rear suspension member rear body mount cushion LH cannot be reused.
Remove SST and the rear suspension member rear body mount cushion LH from the rear suspension member sub-assembly.
52275B
45.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH
Perform the same procedure as for the LH side.
46.REMOVE HOLE PLUG
Remove the 13 hole plugs from the rear suspension member sub-assembly as shown in the illustration.