2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood.


3. REMOVE NO. 1 ENGINE UNDER COVER

4. REMOVE NO. 2 ENGINE UNDER COVER

5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


7. DRAIN TRANSMISSION OIL (for Manual Transmission)
  1. Remove the drain plug and gasket to drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


8. DRAIN TRANSMISSION FLUID (for Automatic Transmission)
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


9. DRAIN POWER STEERING FLUID

10. REMOVE BATTERY CLAMP SUB-ASSEMBLY
  1. Remove the bolt, nut and battery clamp.


11. REMOVE BATTERY

12. REMOVE BATTERY TRAY

13. REMOVE AIR CLEANER ASSEMBLY

  1. A271954
    Detach the wire harness clamp and disconnect the mass air flow meter connector.

  1. Loosen the hose clamp and disconnect No. 1 air cleaner hose from the compressor inlet elbow.

  1. Remove the 2 bolts and air cleaner assembly together with the No. 1 air cleaner hose.


14. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR
(Click here)

15. REMOVE RADIATOR ASSEMBLY
(Click here)

16. REMOVE STARTER ASSEMBLY
  1. for 2.2 kW Type Bosch Made: (Click here)
  2. for 2.2 kW Type Denso Made: (Click here)
  3. for 2.7 kW Type: (Click here)

17. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)

18. REMOVE FRONT PROPELLER SHAFT ASSEMBLY

C098708E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts and 4 washers, and disconnect the propeller shaft.

  1. C098709E01
    Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.


19. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)

20. DISCONNECT HEATER HOSE

  1. A236415
    Disconnect the 2 heater hoses.


21. DISCONNECT PRESSURE FEED TUBE ASSEMBLY

  1. A236416
    Disconnect the oil reservoir to pump hose.

  1. A236417
    Disconnect the pressure feed tube.


22. DISCONNECT FUEL HOSE

  1. A236418
    Disconnect the 2 fuel hoses.


23. DISCONNECT UNION TO CONNECTOR TUBE HOSE

  1. A236419
    Disconnect the union to connector tube hose.


24. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
(Click here)

25. DISCONNECT WIRE HARNESS

A236420
  1. Remove the upper relay block cover.

  1. Remove the side relay block cover.

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.

  1. A233020
    Remove the 2 nuts, detach the clamp and disconnect the wire harness.

  1. Disconnect the 4 glow plug controller connectors.

  1. Disconnect the 4 injector driver connectors.

  1. A260653E01
    Disconnect the 4WD control ECU connector.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  1. for Automatic Transmission:
    Disconnect the 3 TCM connectors.

  1. Disconnect the 6 ECM connectors.


26. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the cooler compressor. With the hoses connected to the cooler compressor, hang the cooler compressor on the vehicle body with a rope.


27. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
(Click here)

28. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission)

29. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

30. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.

  1. Remove the 4 bolts and rear No. 1 engine mounting insulator.


31. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. D029616E01
    Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


32. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.


33. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. A072851E02
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A114803
    Remove the 8 bolts and flywheel.


34. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)

  1. A072851E02
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A114804
    Remove the 8 bolts, rear drive plate spacer, pump impeller drive plate, and flywheel.


35. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.


36. INSTALL ENGINE HANGERS

  1. A224109E01
    Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    Part No.
    No. 1 Engine Hanger
    12284-30020
    No. 2 Engine Hanger
    12282-67030
    Bolt
    91552-81014 and 91642-81030

    NOTICE:
    Install the engine hangers with new bolts.


37. REMOVE ENGINE ASSEMBLY
  1. Attach an engine sling device and hang the engine with a chain block.

  1. A098988E01
    Remove the 4 bolts and 4 nuts.

  1. Remove the engine by operating the engine sling device and chain block.


38. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand with bolts.

  1. Remove the 2 bolts and 2 engine hangers.


39. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.


40. REMOVE FRONT ENGINE MOUNTING INSULATOR

  1. A233592E03
    Remove the 2 nuts and 2 front engine mounting insulators.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side


41. REMOVE NO. 1 TIMING BELT COVER

  1. A015094E01
    Remove the 6 bolts, 6 washers and timing belt cover.


42. REMOVE TIMING BELT

  1. A070549E05
    Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
    Text in Illustration 
    *1
    Timing Mark

    HINT:
    If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.

  1. A070550E01
    Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.

  1. Remove the timing belt.

    HINT:
    A070551E02
    1. If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, turn the camshaft to align the timing marks, and then turn the crankshaft clockwise to align the timing marks.


43. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

NOTICE:
When inspecting the No. 1 timing belt idler, do not remove it unless absolutely necessary.

  1. Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.


44. REMOVE CRANKSHAFT PULLEY

  1. A251844E01
    Using SST, hold the crankshaft pulley and loosen the pulley bolt.
    SST
    09213-58014  
    09330-00021  

  1. A251845E01
    Using SST, remove the pulley bolt and crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.


45. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 2 intercooler support bracket.


46. REMOVE NO. 1 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 1 intercooler support bracket.


47. REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)
(Click here)

48. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
  1. Remove the 4 bolts and No. 1 viscous heater bracket.


49. REMOVE NO. 2 IDLE PULLEY ASSEMBLY
  1. Remove the bolt, pulley plate, No. 2 idle pulley and spacer.


50. REMOVE GENERATOR ASSEMBLY

A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.


51. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.


52. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A098937E01
    Remove the 4 bolts and V-ribbed belt tensioner.


53. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.


54. REMOVE TURBOCHARGER SUB-ASSEMBLY
(Click here)

55. REMOVE EXHAUST MANIFOLD

  1. A152664
    Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.

  1. Remove the gasket.


56. REMOVE WATER INLET

A250419
  1. Disconnect the wire harness clamp.

  1. Remove the 3 bolts and water inlet.

  1. Remove the bolt and wire harness clamp bracket from the water inlet.


57. REMOVE THERMOSTAT
  1. Remove the thermostat from the cylinder block.

  1. Remove the gasket from the thermostat.


58. REMOVE WATER OUTLET

  1. A233596
    Remove the 2 bolts, water outlet and gasket.


59. REMOVE DIESEL THROTTLE BODY ASSEMBLY

  1. A253491
    Disconnect the 2 connectors.

  1. Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.


60. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

61. REMOVE INTAKE MANIFOLD
(Click here)

62. REMOVE GLOW PLUG ASSEMBLY
(Click here)

63. REMOVE FUEL HOSE PROTECTOR

  1. A255187
    Remove the bolt, nut and fuel hose protector.


64. REMOVE NO. 1 FUEL PIPE

  1. A255188
    Remove the No. 1 fuel pipe from the fuel hose bracket.


65. REMOVE FUEL HOSE BRACKET

  1. A255189
    Remove the bolt and fuel hose bracket.


66. REMOVE OIL FILTER SUB-ASSEMBLY

  1. A227248E01
    Using SST, remove the oil filter.
    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the disposal container beneath the drain hose to collect the oil from the oil filter.


67. REMOVE COMMON RAIL ASSEMBLY
(Click here)

68. REMOVE FUEL SUPPLY PUMP ASSEMBLY
(Click here)

69. REMOVE OIL COOLER COVER SUB-ASSEMBLY
  1. Disconnect the oil pressure switch connector.

  1. Remove the 2 nuts and disconnect the No. 2 vacuum transmitting pipe from the oil cooler cover.

  1. A038741E01
    Remove the 13 bolts, oil cooler cover and gasket.


70. REMOVE VACUUM PUMP ASSEMBLY

  1. A098930E01
    Remove the 2 nuts, vacuum pump and 2 O-rings.


71. REMOVE VANE PUMP ASSEMBLY

  1. A233594
    Remove the 2 nuts, vane pump and O-ring.


72. REMOVE CRANKSHAFT POSITION SENSOR
  1. Disconnect the sensor connector.

  1. Remove the 3 clips, bolt and sensor.

    A112048


73. REMOVE CAMSHAFT POSITION SENSOR

A112046
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.


74. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

A112044
  1. Disconnect the sensor connector.

  1. Remove the sensor.

  1. Remove the gasket from the sensor.


75. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

  1. A233593E03
    Remove the 4 bolts and front No. 1 engine mounting bracket.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side


76. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
  1. Remove the 4 bolts and front No. 1 engine mounting bracket.

← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →