The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.
Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD (for 4WD)
2.DISCHARGE FUEL SYSTEM PRESSURE
3. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
5.DRAIN ENGINE COOLANT
6.DRAIN ENGINE OIL
7.DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)
for R151F:
Click hereDrivetrain>R151F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSMISSION OIL>REPLACEMENT
8.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
for AC60E:
Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>TRANSMISSION WIRE>REMOVAL
for AC60F:
Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>TRANSMISSION WIRE>REMOVAL
9.DRAIN DIFFERENTIAL OIL (for 4WD)
53301
10.REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose from the hood sub-assembly.
Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.
17705
11.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
Disconnect the intake mass air flow meter connector and detach the 2 wire harness clamps.
Detach the 4 clamps.
Loosen the hose clamp and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.
17801
12.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
17701
13.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Detach the 3 wire harness clamps.
Remove the 3 bolts and air cleaner case sub-assembly.
17861
14.REMOVE INTAKE AIR CONNECTOR
51410
15.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
51441
16.REMOVE NO. 1 ENGINE UNDER COVER (for 2WD)
51442
17.REMOVE NO. 2 ENGINE UNDER COVER (for 4WD)
51407A
18.REMOVE NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (for 4WD)
53737B
19.REMOVE FRONT UPPER FENDER APRON SEAL LH
w/ Secondary Air Injection System:
Remove the 5 clips and front upper fender apron seal LH.
w/o Secondary Air Injection System:
Remove the 6 clips and front upper fender apron seal LH.
53736
20.REMOVE FRONT UPPER FENDER APRON SEAL RH
w/ Secondary Air Injection System:
Remove the 5 clips and front upper fender apron seal RH.
w/o Secondary Air Injection System:
Remove the 6 clips and front upper fender apron seal RH.
53882F
21.REMOVE FRONT FENDER SEAL LH
for 2WD:
Remove the 5 clips and front fender seal LH.
for 4WD:
Remove the 6 clips and front fender seal LH.
53882F
22.REMOVE FRONT FENDER SEAL RH
for 2WD:
Remove the 5 clips and front fender seal RH.
for 4WD:
Remove the 6 clips and front fender seal RH.
53294C
23.REMOVE RADIATOR SIDE DEFLECTOR LH
53293C
24.REMOVE RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
16593
25.REMOVE NO. 1 RADIATOR AIR GUIDE
16571
26.REMOVE RADIATOR HOSE INLET
16572
27.REMOVE RADIATOR HOSE OUTLET
17621A
28.DISCONNECT AIR PUMP INLET (w/ Secondary Air Injection System)
16470
29.REMOVE RADIATOR RESERVOIR
16711
30.REMOVE FAN SHROUD
32941
31.DISCONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)
32942
32.DISCONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)
16400
33.REMOVE RADIATOR ASSEMBLY
34.DISCONNECT HEATER HOSE
| *A | for LHD |
| *B | for RHD |
| *1 | Heater Water Outlet Hose |
| *2 | Heater Water Inlet Hose |
Slide the clamp and disconnect the heater water outlet hose from the heater radiator unit sub-assembly.
Slide the clamp and disconnect the heater water inlet hose from the heater radiator unit sub-assembly.
44320
35.DISCONNECT VANE PUMP ASSEMBLY
Disconnect the power steering oil pressure switch connector.
Remove the 2 bolts and disconnect the vane pump assembly.
Do not hit other parts with the pulley when disconnecting the vane pump assembly.
Be sure to suspend the vane pump assembly securely.
15301
36.REMOVE ENGINE OIL LEVEL DIPSTICK
11452
37.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the bolt, engine oil level dipstick guide and O-ring.
Cover the engine oil level dipstick guide hole to prevent foreign matter from entering it.
88320
38.DISCONNECT COOLER COMPRESSOR ASSEMBLY
28100
39.REMOVE STARTER ASSEMBLY
40.DISCONNECT PURGE LINE HOSE
Slide the clamp and disconnect the purge line hose from the purge VSV.
44774
41.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Slide the clamp and disconnect the union to connector tube hose from the intake manifold.
17344
42.DISCONNECT NO. 4 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)
23273C
43.DISCONNECT NO. 2 FUEL HOSE
23271H
44.DISCONNECT NO. 1 FUEL HOSE
55550
45.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
89661
46.REMOVE ECM
47.DISCONNECT ENGINE WIRE
| *A | for LHD |
| *B | for RHD |
Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.
| *A | for LHD |
| *B | for RHD |
w/ Secondary Air Injection System:
Disconnect the air injection control driver connector.
Detach the clamp.
Remove the bolt and disconnect the engine wire from the air injection control bracket.
| *A | for LHD |
| *B | for RHD |
w/o Secondary Air Injection System:
Remove the bolt and disconnect the engine wire from the air injection control bracket.
| *A | for LHD |
| *B | for RHD |
Detach the grommet and pull out the engine wire from the cabin.
| *A | for LHD |
| *B | for RHD |
Disconnect the connector from the engine room main wire.
Remove the nut and disconnect the engine room main wire from the positive (+) battery terminal.
Loosen the nut and remove the positive (+) battery terminal.
Loosen the 2 nuts and remove the battery hold down clamp.
Remove the battery.
Remove the battery tray.
Detach the 2 clamps and remove the 2 bolts and disconnect the No. 2 engine wire.
Detach the clamp and remove the bolt and No. 2 engine wire.
Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.
Detach the 2 claws and remove the No. 1 relay block cover side from the engine room relay block.
Remove the nut and disconnect the engine wire from the engine room relay block.
Disconnect the 2 connectors from the engine room relay block.
Detach the clamp.
Remove the bolt and disconnect the wire clamp from the front engine mounting bracket LH.
Disconnect the air fuel ratio sensor connector.
Remove the bolt and disconnect the sensor bracket from the right side of the frame.
17410
48.REMOVE FRONT EXHAUST PIPE ASSEMBLY
51561D
49.REMOVE PROPELLER SHAFT GUARD (for 4WD)
37140
50.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
51569
51.REMOVE PROPELLER SHAFT GUARD
37100
52.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 2WD)
37100
53.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)
43514C
54.REMOVE FRONT AXLE HUB GREASE CAP LH (for 4WD)
43502H
55.REMOVE FRONT AXLE SHAFT NUT LH (for 4WD)
89543
56.DISCONNECT FRONT SPEED SENSOR LH (for 4WD)
57.DISCONNECT TIE ROD END SUB-ASSEMBLY LH (for 4WD)
48069
58.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH (for 4WD)
43420
59.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)
43410
60.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)
Use the same procedure described for the LH side.
43410D
61.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for 4WD)
62.SECURE STEERING WHEEL ASSEMBLY (for 4WD)
45219
63.DISCONNECT STEERING SLIDING YOKE (for 4WD)
44250
64.REMOVE POWER STEERING LINK ASSEMBLY (for 4WD)
41110F
65.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
33030
66.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
35000
67.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
31210
68.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
31250
69.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
13405
70.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
32101
71.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
11355
72.REMOVE REAR END PLATE
Remove the bolt and disconnect the No. 1 water by-pass pipe from the rear end plate.
Remove the bolt and rear end plate from the cylinder block sub-assembly.
73.INSTALL ENGINE HANGER
| *a | Rear Side |
| *b | Front Side |
Install the 2 engine hangers with the 2 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-0C010
12281-0C030 |
| Bolt | 90119-T0388
91672-81025 |
74.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine assembly with a chain block.
Remove the 4 bolts and 4 nuts from the body.
Remove the engine assembly by operating the engine sling device and chain block.
Make sure that the engine is clear of all wiring and hoses.
While lowering the engine from the vehicle, do not allow it to contact the vehicle.
75.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine to an engine stand with bolts.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Remove the 2 bolts and 2 engine hangers.
82121
76.REMOVE ENGINE WIRE
Remove the engine wire from the engine assembly.
12391
77.REMOVE FRONT ENGINE MOUNTING HEAT INSULATOR RH
Remove the bolt and front engine mounting heat insulator RH from the front engine mounting insulator.
12361
78.REMOVE FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
| *a | LH Side |
| *b | RH Side |
Remove the 2 nuts and 2 front engine mounting insulators from the 2 front engine mounting brackets.