The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the engine assembly removal/installation are shown below.
The engine assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fan when working in the engine compartment with the engine running.
Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
1.DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
4.DRAIN ENGINE COOLANT
5.DRAIN ENGINE OIL
6.DRAIN MANUAL TRANSMISSION OIL
53301
7.REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose from the hood sub-assembly.
Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.
17705
8.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
Disconnect the intake mass air flow meter connector and detach the 2 wire harness clamps.
Detach the 4 clamps.
Loosen the hose clamp and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.
17801
9.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
17701
10.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Detach the 3 wire harness clamps.
Remove the 3 bolts and air cleaner case sub-assembly.
17861
11.REMOVE INTAKE AIR CONNECTOR
53737B
12.REMOVE FRONT UPPER FENDER APRON SEAL LH
Remove the 6 clips and front upper fender apron seal LH.
53736
13.REMOVE FRONT UPPER FENDER APRON SEAL RH
Remove the 6 clips and front upper fender apron seal RH.
53882F
14.REMOVE FRONT FENDER SEAL LH
Remove the 5 clips and front fender seal LH.
53882F
15.REMOVE FRONT FENDER SEAL RH
Remove the 5 clips and front fender seal RH.
51410
16.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (w/ Cover)
51441
17.REMOVE NO. 1 ENGINE UNDER COVER (w/ Cover)
53294C
18.REMOVE RADIATOR SIDE DEFLECTOR LH
for Resin Type Bumper:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Resin Type Bumper)>REMOVAL
for Steel Type Bumper:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Steel Type Bumper)>REMOVAL
53293C
19.REMOVE RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
16593
20.REMOVE NO. 1 RADIATOR AIR GUIDE
16571
21.REMOVE RADIATOR HOSE INLET
16572
22.REMOVE RADIATOR HOSE OUTLET
16470
23.REMOVE RADIATOR RESERVOIR
16711
24.REMOVE FAN SHROUD
16400
25.REMOVE RADIATOR ASSEMBLY
26.DISCONNECT HEATER HOSE
| *A | for LHD |
| *B | for RHD |
| *1 | Heater Water Outlet Hose |
| *2 | Heater Water Inlet Hose |
Slide the clamp and disconnect the heater water outlet hose from the heater radiator unit sub-assembly.
Slide the clamp and disconnect the heater water inlet hose from the heater radiator unit sub-assembly.
44320
27.DISCONNECT VANE PUMP ASSEMBLY
Disconnect the power steering oil pressure switch connector.
Remove the 2 bolts and disconnect the vane pump assembly.
Do not hit other parts with the pulley when disconnecting the vane pump assembly.
Be sure to suspend the vane pump assembly securely.
15301
28.REMOVE ENGINE OIL LEVEL DIPSTICK
11452
29.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the bolt, engine oil level dipstick guide and O-ring.
Cover the engine oil level dipstick guide hole to prevent foreign matter from entering it.
88320
30.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
28100
31.REMOVE STARTER ASSEMBLY
for DENSO Made:
Click hereEngine / Hybrid System>1TR-FE STARTING>STARTER(for DENSO Made)>REMOVAL
for BOSCH Made:
Click hereEngine / Hybrid System>1TR-FE STARTING>STARTER(for BOSCH Made)>REMOVAL
32.DISCONNECT PURGE LINE HOSE
Slide the clamp and disconnect the purge line hose from the purge VSV.
44774
33.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Slide the clamp and disconnect the union to connector tube hose from the intake manifold.
23273C
34.DISCONNECT NO. 2 FUEL HOSE
23271H
35.DISCONNECT NO. 1 FUEL HOSE
55550
36.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
89661
37.REMOVE ECM
38.DISCONNECT ENGINE WIRE
| *A | for LHD |
| *B | for RHD |
Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.
| *A | for LHD |
| *B | for RHD |
Remove the bolt and disconnect the engine wire.
| *A | for LHD |
| *B | for RHD |
Detach the clamp and grommet and pull out the engine wire from the cabin.
| *A | for LHD |
| *B | for RHD |
Disconnect the connector from the engine room main wire.
Remove the nut and disconnect the engine room main wire from the positive (+) battery terminal.
Loosen the nut and remove the positive (+) battery terminal.
Loosen the 2 nuts and remove the battery hold down clamp.
Remove the battery.
Remove the battery tray.
Detach the 2 clamps and remove the 2 bolts and disconnect the No. 2 engine wire.
Detach the clamp and remove the bolt and No. 2 engine wire.
Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.
Detach the 2 claws and remove the No. 1 relay block cover side from the engine room relay block.
Remove the nut and disconnect the engine wire from the engine room relay block.
Disconnect the 2 connectors from the engine room relay block.
Detach the clamp.
Remove the bolt and disconnect the wire clamp from the front engine mounting bracket LH.
Disconnect the air fuel ratio sensor connector.
Remove the bolt and disconnect the sensor bracket from the right side of the frame.
17410
39.REMOVE FRONT EXHAUST PIPE ASSEMBLY
51569
40.REMOVE PROPELLER SHAFT GUARD
37100
41.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
33030
42.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY
31210
43.REMOVE CLUTCH COVER ASSEMBLY
31250
44.REMOVE CLUTCH DISC ASSEMBLY
13405
45.REMOVE FLYWHEEL SUB-ASSEMBLY
11355
46.REMOVE REAR END PLATE
Remove the bolt and disconnect the No. 1 water by-pass pipe from the rear end plate.
Remove the bolt and rear end plate from the cylinder block.
47.INSTALL ENGINE HANGER
| *a | Rear Side |
| *b | Front Side |
Install the 2 engine hangers with the 2 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-0C010
12281-0C030 |
| Bolt | 90119-T0388
91672-81025 |
48.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine assembly with a chain block.
Remove the 4 bolts and 4 nuts from the body.
Remove the engine assembly by operating the engine sling device and chain block.
Make sure that the engine is clear of all wiring and hoses.
While lowering the engine from the vehicle, do not allow it to contact the vehicle.
49.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine to an engine stand with bolts.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Remove the 2 bolts and 2 engine hangers.
82121
50.REMOVE ENGINE WIRE
Remove the engine wire from the engine assembly.
12391
51.REMOVE FRONT ENGINE MOUNTING HEAT INSULATOR RH
Remove the bolt and front engine mounting heat insulator RH from the front engine mounting insulator sub-assembly.
12361
52.REMOVE FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
| *a | LH Side |
| *b | RH Side |
Remove the 2 nuts and 2 front engine mounting insulator from the 2 front No. 1 engine mounting brackets.