Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM J

1KD-FTV ENGINE CONTROL  ECD SYSTEM  Engine Difficult to Start or Stalling  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Mass Air Flow Meter
Main fault Decrease in performance (foreign matter is stuck)
Symptoms Lack of power, black smoke
Data List MAF
HINT:

The maximum fuel injection volume is controlled according to the output from the mass air flow meter.



Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbo and intake manifold


Data List
·

MAP

·

Target Booster Pressure

When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, then a lack of power will be felt.



Turbocharger System
Main fault
·

Air leak in the turbocharged air passage

·

ECM not operating well

·

Turbocharger (turbine, bearing)


Symptoms Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped)
Data List MAP, Target Booster Pressure
·

When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, then a lack of power will be felt.

·

With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.

·

Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.


VN Turbo Command
·

0%: Vanes fully open (drive rod contracts)

·

Over 90%: Vanes fully closed (drive rod expands and turbo operates effectively)


Diagnostic Point
·

Using the "Test the Turbo Charger Step Motor" Active Test, check the drive rod movement.

·

Check the drive rod movement when the ignition switch is turned from ON to off.



Exhaust System
Main fault Blockage
Symptoms Lack of power (high engine speed, under heavy load)
Data List MAP
When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, then a lack of power will be felt.

Glow System
Main fault Open circuit, glow plug relay fault
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Measure the resistance of the glow plug

Battery
Main fault Battery is depleted
Symptoms Difficult to start (cannot crank, crank speed is low), horn is quiet
Data List Battery Voltage
When cranking, battery voltage is below 5 V.

Engine - 1
Main fault Damaged, seized up
Symptoms Cannot crank, crank speed is low, strange noise

Engine - 2
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.



Start System
Main fault Starter system malfunction
Symptoms Difficult to start
Data List Starter Signal
·

Ignition switch (STA) output:

ON: Starter is operating

OFF: Starter is not operating




b.

Diesel Injection

Fuel Supply Pump Assembly
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
·

In a stable condition (e.g. idling), Fuel Press is within 5000 kPa of "Target Common Rail Pressure".

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Fuel Filter Element Sub-assembly
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

In a stable condition (e.g. idling), the fuel pressure is within 5000 kPa of "Target Common Rail Pressure".

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).



Pressure Discharge Valve
Main fault Does not completely close
Symptoms Difficult to start, engine stall, rough idle, lack of power

Injector Driver
Main fault Circuit fault: The injector assembly does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as injector assembly
Diagnostic Trouble Code When the injector driver has a fault, some DTCs may be stored.

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Press follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (however, the value may not deviate even when a malfunction is present).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close completely


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).


Data List Actual EGR Valve Pos., Target EGR Pos.
·

Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Pos. (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.


EGR Close Lrn. Val., EGR Close Lrn. Status
·

When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V.

·

In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List
·

Actual Throttle Position

0%: Fully open

100%: Fully closed

·

When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Starting Trouble


·

MAP

·

MAF

·

Intake Air

·

Coolant Temp

·

Battery Voltage

·

Starter Signal

·

Engine Speed of Cyl #1 (to #4)

·

Target Common Rail Pressure

·

Fuel Press

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position

·

Target EGR Position

·

Actual EGR Valve Pos.

·

EGR Close Lrn. Status

·

EGR Close Lrn. Val.



CAUTION / NOTICE / HINT

Explanation of Symptom



Starting Trouble For good starting it is essential to have:
·

Sufficient cranking speed.

·

Properly operating engine preheating system.

·

Good quality fuel.


The fuel is ignited by the heat which is generated by compression pressure.
With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is poor due to leakage, the compression pressure will not rise and there will be difficulty starting.
When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air.
Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the injector assembly is open.

Trouble Area Chart According to Problem Cause



A210593E02
0.844,8.5 1.029,8.669 0.185,0.169 10 A 3.593,0.948 5.204,1.132 1.611,0.184 10 Depleted battery 0.25,0.114 1.281,0.298 1.031,0.184 10 Difficult to start 0.869,0.922 2.254,1.093 1.386,0.171 10 Does not crank at all 0.775,4.096 2.405,4.289 1.630,0.192 10 Cranking speed too slow 0.793,5.59 2.814,5.778 2.022,0.188 10 Difficult to start (cranking is OK) 3.593,1.692 6.021,1.900 2.428,0.208 10 ECM power supply circuit malfunction 3.593,2.481 6.225,2.678 2.632,0.198 10 Clutch pedal switch assembly malfunction 3.593,3.171 6.033,3.505 2.439,0.333 10 Immobiliser system or entry and start system fault 3.593,4.086 4.857,4.270 1.263,0.184 10 Depleted battery 4.119,6.519 6.782,6.696 2.663,0.177 10 Fuel is not supplied to fuel supply pump 1.718,6.518 3.049,6.689 1.330,0.171 10 Fuel pressure is low 4.119,7.287 6.029,7.495 1.911,0.208 10 Fuel supply pump malfunction 4.119,8.067 6.390,8.265 2.272,0.198 10 Common rail assembly malfunction 3.593,4.868 6.360,5.225 2.767,0.357 10 Increased internal friction of the engine mechanical parts (oil too thick, seizure, etc.)

A183464E03
0.843,0.089 1.004,0.258 0.161,0.169 10 A 4.189,0.727 6.291,0.910 2.102,0.184 10 Injector driver circuit malfunction 1.761,0.722 3.119,0.893 1.358,0.171 10 Fuel pressure is high 4.172,1.495 5.659,1.703 1.487,0.208 10 Air in injector assembly 4.203,2.35 6.120,2.533 1.917,0.184 10 Injector assembly malfunction 1.775,2.333 3.161,2.536 1.386,0.203 10 Specific cylinder fault 4.186,3.106 5.928,3.314 1.742,0.208 10 Low compression pressure 4.189,3.973 5.819,4.157 1.630,0.184 10 Glow system malfunction 1.761,3.944 3.403,4.147 1.642,0.203 10 Difficult to start when cold 4.172,4.717 6.401,5.066 2.229,0.349 10 Engine coolant temperature sensor malfunction 1.761,6.093 2.851,6.296 1.090,0.203 10 Poor fuel quality

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result
Result Proceed to
Does not crank at all. A
Low cranking speed.
HINT:

When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.


B
Cranking is OK. C



A

2.CHECK BATTERY CONDITION

B

C

6.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
2.CHECK BATTERY CONDITION

OK

3.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM

NG

REPLACE BATTERY

3.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Check if the normal starting screen appears (check whether communication with the ECM is possible).

HINT:

Use a tester that is able to communicate with other vehicles.


OK:

Communication is possible (vehicle can be recognized).




OK

4.READ VALUE USING INTELLIGENT TESTER (CLUTCH SWITCH)

NG

46.CHECK VC OUTPUT CIRCUIT
4.READ VALUE USING INTELLIGENT TESTER (CLUTCH SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Clutch Switch.


d.

Read the value displayed on the tester.

OK:
Tester Display Condition Specified Condition
Clutch Switch Clutch pedal depressed ON


Result
Result Proceed to
OK A
NG B



A

5.READ ALL OUTPUT DTCS

B

REPLACE CLUTCH SWITCH ASSEMBLY

5.READ ALL OUTPUT DTCS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Utility / All Codes.

Result
Result Proceed to
No DTC is output A
DTCs related to engine are output B



A

END

B

6.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
a.

Check if the fuel level is low.

Result
Result Proceed to
The indicator (fuel warning light) is not illuminated A
The indicator (fuel warning light) is illuminated B



A

7.CHECK INITIALIZATION (FUEL SUPPLY PUMP)

B

43.ADD FUEL
7.CHECK INITIALIZATION (FUEL SUPPLY PUMP)
a.

When the engine does not start or another problem such as rough idling is present, perform initialization and check to see if the problem symptoms disappear. If the problem symptoms do not disappear, perform the next procedure.

HINT:

When replacing the ECM, the fuel supply pump initialization must be performed (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).




NEXT

8.READ OUTPUT DTC (RELATED TO ENGINE)
8.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
DTCs related to engine are output B



A

9.TAKE SNAPSHOT DURING STARTING AND IDLING

B

REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT

9.TAKE SNAPSHOT DURING STARTING AND IDLING
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.


d.

Take a snapshot of the following Data List items with the intelligent tester during "ignition switch ON (5 seconds) → Starting → Idling (10 seconds)".

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.

·

Graphs like the ones shown below can be displayed by transferring the stored snapshot from the tester to a PC. Intelligent Viewer must be installed on the PC.




A176220E02
2.528,2.406 3.209,2.737 0.681,0.332 10 Snapshot Button 2.068,2.712 2.352,2.506 false 2.352,2.506 2.465,2.506 false


NEXT

10.CHECK SNAPSHOT (FUEL PRESS)
10.CHECK SNAPSHOT (FUEL PRESS)
a.

Check Fuel Press in the snapshot taken when the engine was starting.

Result
Result Proceed to
2 seconds after Starter Signal turns from OFF to ON, Fuel Press is below 20000 kPa
HINT:

As long as the fuel pressure remains below 5000 kPa, the ECM stops sending the injection command signal (IJT) to the injector driver, and then the actual injection duration remains 0 microseconds.


A
2 seconds after Starter Signal turns from OFF to ON, Fuel Press is 50000 kPa or higher B
Except above C

HINT:
·

Fuel pressure is about 30000 to 40000 kPa when the engine is cranking and the engine coolant temperature is 0°C (32°F) or higher.

·

Fuel pressure increases rapidly during cranking.





A

11.CHECK ENGINE STARTING CONDITION

B

35.CHECK SNAPSHOT

C

23.INSPECT INJECTOR COMPENSATION CODE
11.CHECK ENGINE STARTING CONDITION
a.

Check whether the engine can be started.

HINT:

If there are deposits in the injector assemblies and they are left for a long time, the injector assemblies for all the cylinders may become stuck.


Result
Result Proceed to
The engine can be started. A
There is no initial combustion even when the engine can be cranked. B



A

12.INSPECT COMMON RAIL ASSEMBLY

B

13.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
12.INSPECT COMMON RAIL ASSEMBLY
a.

Inspect the common rail assembly (See page Engine / Hybrid System>1KD-FTV (FUEL)>COMMON RAIL>INSPECTION).



OK

43.ADD FUEL

NG

20.REPLACE COMMON RAIL
13.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the fuel supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.

OK:

Fuel is properly supplied to the fuel supply pump when the priming pump is operated.


HINT:
·

When there is a lack of fuel, fuel pressure drops.

·

Inspect for fuel filter element sub-assembly clogging (check that the fuel filter element sub-assembly is not clogged).




c.

Reconnect the inlet hose.



OK

14.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

42.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
14.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C71-1 - C92-23 (PCV+) Always Below 1 Ω
C71-2 - C92-12 (PCV-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C71-1 or C92-23 (PCV+) - Body ground Always 10 kΩ or higher
C71-2 or C92-12 (PCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.



OK

15.REPLACE SUCTION CONTROL VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE SUCTION CONTROL VALVE
a.

Replace the suction control valve (See page Engine / Hybrid System>1KD-FTV (FUEL)>SUCTION CONTROL VALVE>REMOVAL).



NEXT

16.BLEED AIR FROM FUEL SYSTEM
16.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

17.PERFORM FUEL SUPPLY PUMP INITIALIZATION
17.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform fuel supply pump initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



NEXT

18.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
18.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


d.

Start the engine.


e.

Read the Fuel Press values while cranking and idling the engine.

Result
Result Proceed to
The engine cannot be started or the engine can be started but Fuel Press is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A



A

END

B

19.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
19.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug assembly for all the cylinders (See page Engine / Hybrid System>1KD-FTV (STARTING)>GLOW PLUG>REMOVAL).


b.

Visually check if there is fuel on the glow plugs.

HINT:
·

If there is fuel on a glow plug, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.



Result
Result Proceed to
No fuel on glow plugs A
Fuel on glow plugs B


c.

Install the glow plug assembly (See page Engine / Hybrid System>1KD-FTV (STARTING)>GLOW PLUG>INSTALLATION).



A

20.REPLACE COMMON RAIL

B

28.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
20.REPLACE COMMON RAIL
a.

Replace the common rail (See page Engine / Hybrid System>1KD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

21.BLEED AIR FROM FUEL SYSTEM
21.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

22.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
22.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


d.

Start the engine.


e.

Read the Fuel Press values while cranking and idling the engine.

Result
Result Proceed to
The engine cannot be started or the engine can be started but Fuel Press is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A



A

END

B

38.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
23.INSPECT INJECTOR COMPENSATION CODE
a.

Read the injector compensation code (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).

OK:

Compensation codes stored in the ECM match compensation codes of the installed injector assemblies.




OK

24.CHECK DATA LIST

NG

REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

24.CHECK DATA LIST
a.
A176220E02
2.528,2.406 3.209,2.737 0.681,0.332 10 Snapshot Button 2.068,2.712 2.352,2.506 false 2.352,2.506 2.465,2.506 false

Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken when the engine was idling.

Result
Result Proceed to
Injection Feedback Val #1 to #4 are more than 3 mm3/st.
HINT:

There may be a malfunction in the corresponding cylinder.


A
Injection Feedback Val #1 to #4 are 3 mm3/st or less.
Injection Volume is more than 10 mm3/st.
B*
Injection Feedback Val #1 to #4 are 3 mm3/st or less.
Injection Volume is 10 mm3/st or less.
C

HINT:
·

*: When this case occurs, usually symptoms may be noticeable, such as difficulty starting, rough idling, knocking or black smoke at high common rail pressure.

·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.





A

25.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

B

38.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

C

29.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
25.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.


HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




NEXT

26.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)
26.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.


d.

Check the engine speed during the Active Test.

OK:

The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other.


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a loss of compression in that cylinder.




OK

28.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

27.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
27.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.


a.

Check the cylinder compression pressure (See page Engine / Hybrid System>1KD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).



OK

28.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

28.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
HINT:

It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.


a.

Replace the injector assembly (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).



NEXT

39.BLEED AIR FROM FUEL SYSTEM
29.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
a.

Check the temperature when starting trouble occurs.


Result
Result Proceed to
Difficult to start only for cold engine. A
Difficult to start both for cold and warmed up engine. B


A

30.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

32.CHECK FUEL QUALITY
30.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.


OK

31.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

31.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

OK

32.CHECK FUEL QUALITY

NG

32.CHECK FUEL QUALITY
a.

Check that fuel with a low cetane number is used.



NEXT

33.CHECK ENGINE STARTING CONDITION
33.CHECK ENGINE STARTING CONDITION
a.

Check whether the engine can be started.

HINT:

If there are deposits in the injector assemblies and they are left for a long time, the injector assemblies for all the cylinders may become stuck.


Result
Result Proceed to
The engine can be started. A
There is no initial combustion even when the engine can be cranked. B



A

34.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

B

38.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
34.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the difficulty starting has been successfully repaired by starting the engine.



NEXT

END

35.CHECK SNAPSHOT
HINT:

When all Data List values are OK and Fuel Press is higher than Target Common Rail Pressure, perform the following inspection.



NEXT

36.INSPECT INJECTOR DRIVER (POWER SOURCE)
36.INSPECT INJECTOR DRIVER (POWER SOURCE)
a.
U169188E01
0.546,1.307 0.827,1.459 0.281,0.152 10 C88 0.626,0.765 1.101,0.912 0.476,0.147 10 +B (+) 1.7,1.206 1.173,0.859 false 0.074,0.119 0.273,0.271 0.199,0.152 10 *a 2.456,1.662 3.024,1.809 0.568,0.147 10 GND (-) 2.443,1.647 1.989,1.258 false

Disconnect the injector driver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C88-2(+B) - C88-3(GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Injector Driver)


c.

Reconnect the injector driver connector.



OK

37.INSPECT INJECTOR ASSEMBLY

NG

37.INSPECT INJECTOR ASSEMBLY
HINT:

If there is no initial combustion during cranking, there may be air in the injector assemblies.



NEXT

END

38.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).



NEXT

39.BLEED AIR FROM FUEL SYSTEM
39.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

40.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
40.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


b.

Perform the injector pilot quantity learning (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



NEXT

41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


d.

Start the engine.


e.

Read the Fuel Press values while cranking and idling the engine.

OK:

The engine can be started and Fuel Press is 20000 kPa or higher 2 seconds after the starter signal changes from OFF to ON.




NEXT

END

42.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
a.

Check and repair or replace the clogged fuel pipe.



NEXT

44.BLEED AIR FROM FUEL SYSTEM
43.ADD FUEL
a.

Add fuel.



NEXT

44.BLEED AIR FROM FUEL SYSTEM
44.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

45.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
45.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


d.

Start the engine.


e.

Read the Fuel Press values while cranking and idling the engine.

OK:

The engine can be started and Fuel Press is 20000 kPa or higher 2 seconds after the starter signal changes from OFF to ON.




NEXT

END

46.CHECK VC OUTPUT CIRCUIT

NEXT

47.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
47.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Check if the normal starting screen appears (check whether communication with the ECM is possible).

HINT:

Use a tester that is able to communicate with other vehicles.


OK:

Communication is possible (vehicle can be recognized).




OK

END

NG

48.CHECK ECM POWER SOURCE CIRCUIT
48.CHECK ECM POWER SOURCE CIRCUIT

NEXT

49.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
49.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Check if the normal starting screen appears (check whether communication with the ECM is possible).

HINT:

Use a tester that is able to communicate with other vehicles.


OK:

Communication is possible (vehicle can be recognized).




OK

END

NG