Home › Engine / Hybrid System › 5L-E (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM27T0E _51 Engine / Hybrid System _053661 5L-E ENGINE MECHANICAL _0260486 CYLINDER HEAD GASKET A

5L-E ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.

Check the piston protrusion for each cylinder.

i.
A058740E03
2.594,0.51 2.813,0.281 2.813,0.281 2.906,0.281 true 3.083,1.26 2.979,1.26 2.979,1.26 2.75,1.375 true 2.958,0.188 3.156,0.375 0.198,0.188 10 false *a 3.135,1.167 3.323,1.333 0.188,0.167 10 false *b

Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.

Text in Illustration
*a Measuring Tip
*b Protrusion


ii.
A056896E05
2.604,1.469 3.281,1.844 0.677,0.375 10 true 25 mm (0.984 in.) 0.104,1.385 0.833,1.74 0.729,0.354 10 true 25 mm (0.984 in.) 1.521,1.521 1.896,1.708 0.375,0.188 10 true X: *a

Measure the protrusion of each cylinder at 2 places as shown in the illustration, making a total of 8 measurements.

Text in Illustration
*a Measuring Point
V100135

Front


iii.

For the piston protrusion value of each cylinder, use the average of the 2 measurements of that cylinder.

Standard protrusion:

0.68 to 0.98 mm (0.0268 to 0.0386 in.)


After installing the piston and connecting rod assembly, if the protrusion is not as specified, remove the piston and connecting rod assembly and reinstall them.



b.
A057643E05
1.594,0.448 1.594,0.271 1.594,0.271 1.656,0.271 true 1.854,0.542 1.854,0.385 1.854,0.385 1.906,0.385 false 2.802,0.875 2.802,0.688 2.802,0.688 2.74,0.688 false 1.708,0.177 1.896,0.365 0.188,0.188 10 false B 1.948,0.313 2.125,0.49 0.177,0.177 10 false D 2.594,0.615 2.729,0.813 0.135,0.198 10 false F 1.083,0.354 1.281,0.542 0.198,0.188 10 false *1

Select a new cylinder head gasket.

Text in Illustration
*1 Cutout Mark
V100135

Front

HINT:

There are 3 sizes of new cylinder head gaskets, marked "B", "D" or "F" accordingly.


New Cylinder Head Gasket Thickness:
Item Specified Condition
Mark B 1.40 to 1.50 mm (0.0551 to 0.0591 in.)
Mark D 1.50 to 1.60 mm (0.0591 to 0.0630 in.)
Mark F 1.60 to 1.70 mm (0.0630 to 0.0669 in.)


i.

Select the largest piston protrusion value from the measurements made, then select a new appropriate gasket according to the table below.

Gasket Size:
Piston Protrusion Gasket Size
0.68 to 0.78 mm (0.0268 to 0.0307 in.) Use B
0.78 to 0.88 mm (0.0307 to 0.0346 in.) Use D
0.88 to 0.98 mm (0.0346 to 0.0385 in.) Use F




c.
A056909

Install the selected cylinder head gasket to the cylinder block.

NOTICE:

Make sure that the gasket is installed facing the proper direction.

Be careful of the installation direction.



Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

The cylinder head bolts are tightened in 3 progressive steps.

·

Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.

·

If any bolt is broken or deformed, replace it.



a.
A058738

Using the crankshaft pulley bolt, turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

Text in Illustration
V100135

Turn


b.

Place the cylinder head on the cylinder block.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head.

·

Place the cylinder head on the cylinder block gently in order not to damage the gasket with the bottom part of the head.




c.

Install the plate washers to the cylinder head bolts.


d.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


e.

Step 1:

i.
A058739E03
3.021,0.531 3.24,0.698 0.219,0.167 10 false (B) 3.031,0.75 3.219,0.896 0.188,0.146 10 false 15 2.354,0.531 2.573,0.698 0.219,0.167 10 false (B) 2.417,0.75 2.521,0.896 0.104,0.146 10 false 7 1.667,0.531 1.885,0.698 0.219,0.167 10 false (B) 1.74,0.75 1.833,0.896 0.094,0.146 10 false 1 0.979,0.531 1.198,0.698 0.219,0.167 10 false (B) 1.042,0.75 1.146,0.896 0.104,0.146 10 false 9 0.313,0.531 0.531,0.698 0.219,0.167 10 false (B) 0.323,0.75 0.51,0.896 0.188,0.146 10 false 17 3.052,2.375 3.271,2.542 0.219,0.167 10 false (B) 3.073,2.208 3.26,2.354 0.188,0.146 10 false 18 2.375,2.375 2.594,2.542 0.219,0.167 10 false (B) 2.396,2.208 2.573,2.354 0.177,0.146 10 false 10 1.667,2.375 1.885,2.542 0.219,0.167 10 false (B) 1.74,2.208 1.833,2.354 0.094,0.146 10 false 2 0.979,2.375 1.198,2.542 0.219,0.167 10 false (B) 1.042,2.208 1.146,2.354 0.104,0.146 10 false 8 0.292,2.375 0.51,2.542 0.219,0.167 10 false (B) 0.302,2.208 0.49,2.354 0.188,0.146 10 false 16 2.677,0.396 2.896,0.563 0.219,0.167 10 false (A) 2.688,0.615 2.875,0.76 0.188,0.146 10 false 13 1.99,0.396 2.208,0.563 0.219,0.167 10 false (A) 2.052,0.615 2.156,0.76 0.104,0.146 10 false 5 1.313,0.396 1.531,0.563 0.219,0.167 10 false (A) 1.375,0.615 1.479,0.76 0.104,0.146 10 false 3 0.646,0.396 0.865,0.563 0.219,0.167 10 false (A) 0.656,0.615 0.844,0.76 0.188,0.146 10 false 11 2.74,2.604 2.958,2.771 0.219,0.167 10 false (B) 2.75,2.427 2.938,2.573 0.188,0.146 10 false 12 2.052,2.604 2.271,2.771 0.219,0.167 10 false (B) 2.115,2.427 2.219,2.573 0.104,0.146 10 false 4 1.354,2.604 1.573,2.771 0.219,0.167 10 false (B) 1.427,2.427 1.531,2.573 0.104,0.146 10 false 6 0.667,2.604 0.885,2.771 0.219,0.167 10 false (B) 0.688,2.427 0.875,2.573 0.188,0.146 10 false 14

Install and uniformly tighten the 18 cylinder head bolts, in several steps, in the sequence shown in the illustrations.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

HINT:

Each bolt length is indicated below.


Standard Bolt:
Item Length
Bolt A 107 mm (4.21 in.)
Bolt B 127 mm (5.00 in.)


If any one of the cylinder head bolts does not meet the torque specification, replace the cylinder set head bolt.



f.

Step 2:

i.

Mark the front side of each cylinder head bolt head with paint.


ii.

Tighten the cylinder head bolts 90° in the sequence shown in step 1.



g.

Step 3:

i.

Tighten the cylinder head bolts another 90° in the sequence shown in step 1.



h.

Check that the paint marks are now at a 180° angle to the front.


Hide 11201 3.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 82715 4.INSTALL WIRING HARNESS CLAMP BRACKET (for LHD)

Hide 5.CONNECT WIRE HARNESS

a.
A229807E01
0.503,1.493 0.662,1.661 0.160,0.168 10 *1 1.65,1.625 1.825,1.773 0.175,0.148 10 *2 0.503,1.957 0.676,2.117 0.173,0.160 10 *3 0.644,2.808 0.811,2.988 0.166,0.180 10 *4 1.961,2.086 2.117,2.248 0.156,0.162 10 *5 1.961,2.508 2.133,2.649 0.173,0.141 10 *6 2.867,2.795 3.038,2.962 0.172,0.167 10 *7 2.174,2.593 2.239,2.593 2.239,2.593 2.402,2.493 false 2.178,2.176 2.243,2.176 2.243,2.176 2.378,2.079 false 2.84,2.894 2.793,2.894 2.793,2.894 2.564,2.786 false 0.723,1.571 0.783,1.571 0.783,1.571 1.076,1.7 false 0.725,2.047 0.781,2.047 0.781,2.047 1.088,2.133 false 1.643,1.723 1.569,1.723 1.569,1.723 1.358,1.885 false 0.829,2.902 0.902,2.902 0.902,2.902 1.152,2.584 false

Connect the engine wire and install the No. 2 glow plug resistor insulator and washer with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Text in Illustration
*1 Nut
*2 Washer
*3 No. 2 Glow Plug Resistor Insulator
*4 Engine Wire
*5 No. 1 Glow Plug Connector
*6 No. 1 Glow Plug Resistor Insulator
*7 Bolt


b.
A229803

Attach the 4 wire harness clamps.


c.

Install the generator wire with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


d.

Install the terminal cap.


e.

Connect the generator connector and cooler compressor connector.


f.

for RHD:

i.
A229804

Attach the 5 wire harness clamps.



g.

for LHD:

i.
A229805

Attach the 4 wire harness clamps.


ii.
A229806

Attach the 3 wire harness clamps.



Hide 17167 8.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 9.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 88431 10.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

a.

Install the No. 1 compressor mounting bracket with the 4 bolts.

Torque:
81 N*m (829 kgf*cm, 60 ft.*lbf)


b.

Connect the generator with the bolt.


Hide 26100 12.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 13568 13.INSTALL TIMING BELT

Hide 17410 14.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Long Wheelbase)

Hide 20.INSPECT FOR EXHAUST GAS LEAK