Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  Short in CAN Bus Lines  


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
·

Short between CAN bus lines

·

Combination meter assembly

·

Master cylinder solenoid (skid control ECU)

·

Main body ECU (multiplex network body ECU)

·

Center airbag sensor assembly

·

Spiral cable sub-assembly (steering angle sensor)

·

Certification ECU (smart key ECU assembly)

·

Power management control ECU

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2

·

Four wheel drive control ECU

·

Power steering ECU assembly

·

Yaw rate sensor assembly

·

ECM

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector



*1: w/ Navigation System (for Navigation Receiver Type)

*2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System


WIRING DIAGRAM

C294485E01
5.661,5.428 5.756,5.578 0.095,0.151 10 6 5.568,5.861 5.755,6.011 0.187,0.151 10 14 2.826,7.251 3.183,7.434 0.357,0.183 10 G132 2.826,7.399 4.453,7.556 1.627,0.157 10 No. 2 Junction Connector 5.867,0.696 6.291,0.849 0.423,0.153 10 CANH 5.867,1.33 6.291,1.477 0.423,0.147 10 CANL 5.644,1.619 6.004,1.793 0.359,0.173 10 G6 5.644,1.781 6.874,2.133 1.230,0.351 10 Combination Meter Assembly 3.906,0.696 4.094,0.847 0.187,0.151 10 10 3.906,1.135 4.094,1.285 0.187,0.151 10 21 3.906,1.593 4.094,1.743 0.187,0.151 10 9 3.906,2.015 4.094,2.165 0.187,0.151 10 20 3.906,3.631 4.094,3.782 0.187,0.151 10 8 3.906,4.054 4.094,4.204 0.187,0.151 10 19 3.066,0.696 3.244,0.847 0.178,0.151 10 11 3.066,1.135 3.254,1.285 0.187,0.151 10 22 3.158,3.631 3.255,3.782 0.097,0.151 10 2 3.066,4.054 3.254,4.204 0.187,0.151 10 13 3.906,5.428 4.094,5.578 0.187,0.151 10 4 3.906,5.861 4.094,6.011 0.187,0.151 10 15 3.158,5.428 3.255,5.578 0.097,0.151 10 5 3.066,5.85 3.254,6.000 0.187,0.151 10 16 0.884,1.253 1.279,1.390 0.396,0.136 10 CANL 0.856,0.799 1.279,0.936 0.423,0.136 10 CANH 1.397,0.696 1.585,0.847 0.187,0.151 10 11 1.397,1.135 1.585,1.285 0.187,0.151 10 25 0.339,1.597 0.696,1.781 0.357,0.183 10 A7 0.339,1.757 2.170,2.123 1.832,0.367 10 Master Cylinder Solenoid (Skid Control ECU) 0.884,4.195 1.279,4.332 0.396,0.136 10 CANL 0.856,3.742 1.279,3.878 0.423,0.136 10 CANH 1.397,3.631 1.579,3.782 0.182,0.151 10 14 1.397,4.054 1.585,4.204 0.187,0.151 10 13 0.297,4.502 0.622,4.673 0.326,0.171 10 G64 0.297,4.653 1.962,4.982 1.665,0.330 10 Main Body ECU (Multiplex Network Body ECU) 5.867,5.992 6.263,6.128 0.396,0.136 10 CANL 5.867,5.538 6.291,5.675 0.423,0.136 10 CANH 0.884,5.992 1.279,6.128 0.396,0.136 10 CANL 0.856,5.538 1.279,5.675 0.423,0.136 10 CANH 1.397,5.428 1.579,5.578 0.182,0.151 10 13 1.397,5.85 1.585,6.001 0.187,0.151 10 22 0.305,6.298 0.631,6.470 0.326,0.171 10 G1 0.305,6.449 1.700,6.779 1.394,0.329 10 Center Airbag Sensor Assembly 5.568,0.696 5.764,0.847 0.196,0.151 10 40 5.568,1.135 5.764,1.285 0.196,0.151 10 39 2.83,2.655 4.462,2.838 1.632,0.183 10 No. 1 Junction Connector 2.83,2.496 3.180,2.679 0.350,0.183 10 A72 6.042,6.462 6.420,6.653 0.379,0.190 10 DLC3 6.047,6.312 6.373,6.483 0.326,0.171 10 G48

C294474E01
5.675,0.623 5.770,0.774 0.095,0.151 10 4 5.675,1.056 5.770,1.207 0.095,0.151 10 3 3.92,2.511 4.108,2.662 0.187,0.151 10 1 3.92,2.933 4.108,3.084 0.187,0.151 10 12 5.32,1.637 7.043,2.001 1.723,0.363 10 Spiral Cable Sub-assembly (Steering Angle Sensor) 3.92,0.623 4.108,0.774 0.187,0.151 10 7 3.92,1.056 4.108,1.207 0.187,0.151 10 18 3.172,0.623 3.269,0.774 0.097,0.151 10 9 3.08,1.045 3.268,1.196 0.187,0.151 10 20 5.32,1.495 5.645,1.666 0.326,0.171 10 G33 5.881,1.187 6.277,1.324 0.396,0.136 10 CANL 5.881,0.734 6.305,0.870 0.423,0.136 10 CANH 0.898,3.068 1.293,3.205 0.396,0.136 10 CANL 0.87,2.615 1.293,2.751 0.423,0.136 10 CANH 1.411,2.504 1.593,2.655 0.182,0.151 10 9 1.411,2.926 1.599,3.077 0.187,0.151 10 10 0.319,3.375 0.645,3.546 0.326,0.171 10 H51 0.319,3.535 2.089,3.865 1.769,0.329 10 Radio and Display Receiver Assembly*2 0.898,1.187 1.293,1.324 0.396,0.136 10 CANL 0.87,0.734 1.293,0.870 0.423,0.136 10 CANH 1.411,0.623 1.593,0.774 0.182,0.151 10 9 1.411,1.045 1.599,1.196 0.187,0.151 10 10 0.366,1.494 0.692,1.665 0.326,0.171 10 H56 0.366,1.654 1.659,1.984 1.293,0.329 10 Navigation Receiver Assembly*1 1.428,4.342 1.614,4.492 0.186,0.151 10 19 1.428,4.787 1.614,4.938 0.186,0.151 10 20 3.914,4.342 4.102,4.492 0.187,0.151 10 1 3.914,4.797 4.102,4.947 0.187,0.151 10 12 3.914,6.234 4.102,6.385 0.187,0.151 10 4 3.914,6.68 4.102,6.830 0.187,0.151 10 15 5.603,6.234 5.784,6.385 0.181,0.151 10 14 5.591,6.68 5.779,6.830 0.187,0.151 10 13 1.439,6.234 1.621,6.385 0.181,0.151 10 1 1.428,6.68 1.615,6.830 0.187,0.151 10 2 3.159,4.342 3.269,4.492 0.110,0.151 10 3 3.087,4.787 3.274,4.938 0.187,0.151 10 14 2.801,3.408 3.158,3.591 0.357,0.183 10 G132 2.801,3.584 4.433,3.767 1.632,0.183 10 No. 2 Junction Connector 2.801,7.826 3.158,8.009 0.357,0.183 10 G134 2.801,7.974 4.433,8.157 1.632,0.183 10 No. 3 Junction Connector 0.279,5.265 0.676,5.431 0.396,0.166 10 G53 5.589,7.128 5.985,7.294 0.396,0.166 10 G51 5.589,7.297 6.898,7.626 1.309,0.330 10 Power Management Control ECU 0.318,7.149 0.758,7.326 0.440,0.177 10 G46 0.318,7.311 1.640,7.680 1.322,0.369 10 Power Steering ECU Assembly 0.279,5.425 2.244,5.788 1.965,0.363 10 Four Wheel Drive Control ECU 3.159,6.234 3.291,6.385 0.132,0.150 10 5 3.087,6.68 3.274,6.831 0.187,0.151 10 16 0.901,4.455 1.324,4.592 0.423,0.137 10 CANH 0.901,4.906 1.324,5.043 0.423,0.137 10 CANL 0.901,6.337 1.324,6.475 0.423,0.137 10 CANH 0.901,6.788 1.324,6.925 0.423,0.137 10 CANL 5.879,6.337 6.302,6.475 0.423,0.137 10 CA1H 5.873,6.788 6.297,6.925 0.423,0.137 10 CA1L 0.135,8.535 5.338,8.698 5.203,0.163 10 *2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System 0.135,8.274 3.713,8.437 3.578,0.163 10 *1: w/ Navigation System (for Navigation Receiver Type)

C329313E01
3.914,2.506 4.102,2.656 0.187,0.151 10 2 3.914,2.946 4.102,3.097 0.187,0.151 10 13 1.288,2.495 1.424,2.645 0.136,0.150 10 3 1.288,2.941 1.402,3.091 0.115,0.151 10 2 3.159,2.495 3.291,2.645 0.132,0.150 10 8 3.087,2.946 3.274,3.097 0.187,0.151 10 19 1.288,0.521 1.514,0.671 0.227,0.150 10 9 1.288,0.966 1.477,1.117 0.189,0.151 10 10 0.177,3.4 0.535,3.584 0.357,0.183 10 G52 0.177,1.44 0.617,1.617 0.440,0.177 10 G38 0.177,1.602 2.055,1.971 1.878,0.369 10 Certification ECU (Smart Key ECU Assembly) 3.159,0.521 3.291,0.671 0.132,0.150 10 6 3.087,0.966 3.274,1.117 0.187,0.151 10 17 5.873,2.487 6.297,2.641 0.423,0.153 10 CANH 5.873,3.132 6.297,3.279 0.423,0.147 10 CANL 6.022,3.42 6.376,3.587 0.354,0.166 10 ECM 2.801,3.389 3.158,3.572 0.357,0.183 10 G134 2.801,3.564 4.433,3.748 1.632,0.183 10 No. 3 Junction Connector 0.177,3.57 2.026,3.901 1.849,0.331 10 Yaw Rate Sensor Assembly 5.464,3.048 5.745,3.187 0.280,0.140 10 G58 5.464,2.598 5.745,2.738 0.280,0.140 10 G58 5.451,2.385 5.758,2.536 0.307,0.151 10 35*4 5.451,2.826 5.758,2.976 0.307,0.151 10 36*4 5.056,3.048 5.336,3.187 0.280,0.140 10 G56 5.056,2.598 5.336,2.738 0.280,0.140 10 G56 5.042,2.385 5.349,2.536 0.307,0.151 10 31*3 5.042,2.826 5.349,2.976 0.307,0.151 10 25*3 4.537,3.048 4.910,3.187 0.373,0.140 10 G184 4.537,2.598 4.910,2.738 0.373,0.140 10 G184 4.566,2.385 4.873,2.536 0.307,0.151 10 17*5 4.566,2.826 4.873,2.976 0.307,0.151 10 28*5 0.761,2.6 1.184,2.737 0.423,0.137 10 CANH 0.789,3.05 1.184,3.188 0.396,0.137 10 CANL 0.761,0.625 1.184,0.762 0.423,0.137 10 CANH 0.789,1.076 1.184,1.213 0.396,0.137 10 CANL 0.202,4.159 4.134,4.322 3.932,0.163 10 *3: for 1GR-FE 0.198,4.439 1.408,4.602 1.210,0.163 10 *4: for 1KD-FTV 1.459,4.159 2.669,4.322 1.210,0.163 10 *5: for 1GD-FTV

CAUTION / NOTICE / HINT

HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
2.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
a.
U148273E02
1.958,0.896 2.146,0.396 2.146,0.396 2.271,0.396 true 1.958,1.479 1.813,1.906 1.813,1.906 1.677,1.906 true 0.094,0 0.26,0.188 0.167,0.188 10 false *a 2.323,0.323 2.792,0.51 0.469,0.188 10 false CANH 1.281,1.823 1.688,2.01 0.406,0.188 10 false CANL 0.26,1.135 0.563,1.323 0.302,0.188 10 false G48

Disconnect the G132 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) Engine switch off 1 MΩ or higher


Text in Illustration
*a Front view of DLC3



OK

3.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

3.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)
4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)
a.
U148273E03
1.979,0.896 2.167,0.396 2.167,0.396 2.292,0.396 true 1.958,1.469 1.813,1.896 1.813,1.896 1.677,1.896 true 0.094,0 0.26,0.188 0.167,0.188 10 false *a 2.333,0.313 2.802,0.5 0.469,0.188 10 false CANH 1.281,1.823 1.688,2.01 0.406,0.188 10 false CANL 0.24,1.125 0.542,1.313 0.302,0.188 10 false G48

Disconnect the G134 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3



OK

5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

27.CONNECT CONNECTOR
5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.
U170290E01
2.374,0.748 2.273,0.748 2.273,0.748 1.86,1.234 false 1.86,1.439 2.113,1.846 2.113,1.846 2.236,1.846 false 2.392,0.671 2.813,0.808 0.421,0.137 10 CANH 2.247,1.764 2.643,1.901 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-5 (CANH) - G134-16 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

NG

11.CONNECT CONNECTOR
6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U170291E01
2.447,0.856 2.346,0.856 2.346,0.856 1.958,1.234 false 1.958,1.439 2.276,1.816 2.276,1.816 2.399,1.816 false 2.465,0.778 2.886,0.915 0.421,0.137 10 CANH 2.41,1.734 2.806,1.871 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-4 (CANH) - G134-15 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)

NG

13.CONNECT CONNECTOR
7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)
a.
U170292E01
2.516,0.89 2.415,0.89 2.415,0.89 2.062,1.234 false 2.062,1.439 2.344,1.78 2.344,1.78 2.467,1.78 false 2.534,0.812 2.954,0.949 0.421,0.137 10 CANH 2.478,1.699 2.874,1.836 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-3 (CANH) - G134-14 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

NG

15.CONNECT CONNECTOR
8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)
a.
U170296E01
1.006,0.791 1.107,0.791 1.107,0.791 1.517,1.234 false 1.517,1.439 1.231,1.827 1.231,1.827 1.108,1.827 false 0.497,0.714 0.918,0.851 0.421,0.137 10 CANH 0.625,1.745 1.021,1.882 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.611,1.259 2.968,1.396 0.357,0.137 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-8 (CANH) - G134-19 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - CERTIFICATION ECU)

NG

17.CONNECT CONNECTOR
9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - CERTIFICATION ECU)
a.
U170293E01
1.086,0.652 1.187,0.652 1.187,0.652 1.736,1.234 false 1.736,1.439 1.431,1.874 1.431,1.874 1.308,1.874 false 0.577,0.574 0.997,0.711 0.421,0.137 10 CANH 0.825,1.792 1.221,1.929 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.611,1.259 2.968,1.396 0.357,0.137 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-6 (CANH) - G134-17 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - ECM)

NG

19.CONNECT CONNECTOR
10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - ECM)
a.
U170288E01
2.516,0.997 2.415,0.997 2.415,0.997 2.169,1.234 false 2.169,1.439 2.388,1.717 2.388,1.717 2.511,1.717 false 2.534,0.92 2.954,1.057 0.421,0.137 10 CANH 2.522,1.635 2.918,1.772 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-2 (CANH) - G134-13 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)

Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1KD-FTV) C
NG (for 1GD-FTV) D



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

21.CONNECT CONNECTOR

C

23.CONNECT CONNECTOR

D

25.CONNECT CONNECTOR
11.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

12.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)
12.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)
a.
U148345E03
1.906,1.531 2.125,1.073 2.125,1.073 2.219,1.073 true 2.375,1.26 2.302,1.26 2.302,1.26 2.031,1.531 true 0.063,0 0.333,0.229 0.271,0.229 10 false *a 2.417,1.188 2.844,1.354 0.427,0.167 10 false CANH 2.26,1.01 2.677,1.177 0.417,0.167 10 false CANL 0.625,1.354 0.948,1.521 0.323,0.167 10 false G46

Disconnect the power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G46-1 (CANH) - G46-2 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

13.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
14.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
a.
U148241E04
1.792,1.302 1.646,1.969 1.646,1.969 1.51,1.969 true 1.729,1.323 1.333,1.76 1.333,1.76 1.24,1.76 true 0.031,0.031 0.271,0.219 0.24,0.188 10 true *a 1.083,1.885 1.458,2.042 0.375,0.156 10 false CA1L 0.74,1.667 1.167,1.823 0.427,0.156 10 false CA1H 0.552,1.188 0.885,1.344 0.333,0.156 10 false G51

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G51-14 (CA1H) - G51-13 (CA1L) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)

15.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

16.CHECK FOR SHORT IN CAN BUS WIRES (FOUR WHEEL DRIVE CONTROL ECU)
16.CHECK FOR SHORT IN CAN BUS WIRES (FOUR WHEEL DRIVE CONTROL ECU)
a.
U148352E03
0.49,1.031 0.573,1.031 0.573,1.031 0.688,1.365 true 0.583,0.729 0.677,0.729 0.677,0.729 0.75,1.375 true 0.052,0 0.219,0.188 0.167,0.188 10 false *a 0.177,0.656 0.604,0.813 0.427,0.156 10 false CANH 0.115,0.948 0.51,1.104 0.396,0.156 10 false CANL 2.427,1.219 2.729,1.375 0.302,0.156 10 false G53

Disconnect the four wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G53-19 (CANH) - G53-20 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)



OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)

17.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)
18.CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)
a.
U148302E03
0.896,1.01 0.99,1.01 0.99,1.01 1.417,1.469 true 1.167,0.563 1.281,0.563 1.281,0.563 1.563,1.458 true 0.052,0 0.229,0.177 0.177,0.177 10 false *a 0.5,0.927 0.906,1.104 0.406,0.177 10 false CANL 0.417,1.438 0.719,1.615 0.302,0.177 10 false G52 0.75,0.49 1.177,0.667 0.427,0.177 10 false CANH

Disconnect the yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G52-3 (CANH) - G52-2 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)

19.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)
20.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)
a.
U169923E02
1.219,1.563 1,0.958 1,0.958 0.927,0.958 true 1.135,1.573 0.646,1.177 0.646,1.177 0.573,1.177 true 0.521,0.885 0.948,1.042 0.427,0.156 10 false CANH 0.167,1.104 0.563,1.26 0.396,0.156 10 false CANL 2.5,1.417 2.823,1.573 0.323,0.156 10 false G38 0.073,0 0.396,0.156 0.323,0.156 10 false *a

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G38-9 (CANH) - G38-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

21.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
22.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U170371E02
1.271,1.573 0.896,1.719 0.896,1.719 0.74,1.719 true 0.792,1.052 0.99,1.052 0.99,1.052 1.281,1.375 true 0.083,0.063 0.281,0.292 0.198,0.229 10 false *a 2.479,0.927 2.76,1.073 0.281,0.146 10 false G56 0.281,0.969 0.76,1.115 0.479,0.146 10 false CANL 0.219,1.635 0.698,1.781 0.479,0.146 10 false CANH

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G56-31 (CANH) - G56-25 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

23.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
24.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U170369E01
0.08,0.062 0.282,0.291 0.202,0.230 10 *a 0.485,1.077 0.770,1.219 0.286,0.142 10 G58 2.087,1.573 2.2,1.72 2.2,1.72 2.355,1.72 false 2.335,1.976 2.133,1.976 2.133,1.976 1.982,1.573 false 2.383,1.643 2.867,1.785 0.483,0.142 10 CANL 2.36,1.898 2.843,2.040 0.483,0.142 10 CANH

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G58-35 (CANH) - G58-36 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

25.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

26.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
26.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U170472E01
1.051,2.08 1.337,2.94 1.337,2.94 1.432,2.94 false 1.472,0.244 1.868,0.422 0.396,0.178 10 G184 1.497,2.84 2.096,3.018 0.599,0.178 10 CANL 1.782,2.463 2.355,2.641 0.573,0.178 10 CANH 0.112,0.096 0.685,0.274 0.573,0.178 10 *a 1.083,1.893 1.63,2.557 1.63,2.557 1.726,2.557 false

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G184-17 (CANH) - G184-28 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

27.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U170294E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G132

Disconnect the No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-1 (CANH) - G132-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

29.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

29.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)
30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)
a.
U148273E04
1.958,0.885 2.146,0.385 2.146,0.385 2.271,0.385 true 1.948,1.448 1.802,1.875 1.802,1.875 1.667,1.875 true 0.094,0 0.26,0.188 0.167,0.188 10 false *a 2.333,0.323 2.802,0.51 0.469,0.188 10 false CANH 1.292,1.802 1.698,1.99 0.406,0.188 10 false CANL 0.26,1.104 0.563,1.292 0.302,0.188 10 false G48

Disconnect the A72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3



OK

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)

NG

37.CONNECT CONNECTOR
31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)
a.
U170295E02
0.969,1.063 1.073,1.063 1.073,1.063 1.198,1.229 true 1.198,1.438 1.083,1.625 1.083,1.625 0.958,1.625 true 0.458,0.99 0.875,1.125 0.417,0.135 10 false CANH 0.479,1.542 0.875,1.677 0.396,0.135 10 false CANL 0.063,0.083 0.458,0.219 0.396,0.135 10 false *a 2.677,1.26 3.01,1.563 0.333,0.302 10 false A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-11 (CANH) - A72-22 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

33.CONNECT CONNECTOR
32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U148889E01
1.006,0.963 1.107,0.963 1.107,0.963 1.31,1.234 false 1.31,1.439 1.171,1.699 1.171,1.699 1.048,1.699 false 0.497,0.886 0.918,1.022 0.421,0.137 10 CANH 0.565,1.618 0.961,1.755 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-10 (CANH) - A72-21 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

35.CONNECT CONNECTOR
33.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

34.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
34.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
a.
U115863E01
0.073,0.08 0.270,0.266 0.197,0.186 10 *a 1.595,0.663 1.881,0.849 0.286,0.186 10 A7 2.493,0.813 2.933,0.999 0.440,0.186 10 CANH 2.864,1.077 3.262,1.246 0.398,0.169 10 CANL 2.207,1.77 2.36,0.902 2.36,0.902 2.465,0.902 false 2.207,1.896 2.765,1.162 2.765,1.162 2.843,1.162 false

Disconnect the master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A7-11 (CANH) - A7-25 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

35.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
36.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U169932E01
0.257,0.575 0.471,0.758 0.214,0.183 10 G6 1.644,0.387 2.064,0.570 0.421,0.183 10 CANL 1.896,0.12 2.329,0.275 0.433,0.156 10 CANH 0.084,0.063 0.413,0.245 0.330,0.183 10 *a 2.835,1.364 2.218,0.475 2.218,0.475 2.124,0.475 false 2.958,1.357 2.508,0.187 2.508,0.187 2.415,0.187 false

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

37.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U170287E01
1.006,0.791 1.107,0.791 1.107,0.791 1.517,1.234 false 1.517,1.439 1.231,1.827 1.231,1.827 1.108,1.827 false 0.497,0.714 0.918,0.851 0.421,0.137 10 CANH 0.625,1.745 1.021,1.882 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.611,1.259 2.968,1.396 0.357,0.137 10 G132

Disconnect the No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-8 (CANH) - G132-19 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)
NOTICE:

For vehicles without a navigation system (for navigation receiver type), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Radio and Display Receiver Assembly)".


a.
U170297E01
0.972,0.95 1.073,0.95 1.073,0.95 1.396,1.234 false 1.396,1.439 1.173,1.769 1.173,1.769 1.05,1.769 false 0.463,0.873 0.883,1.010 0.421,0.137 10 CANH 0.567,1.687 0.963,1.824 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.611,1.259 2.968,1.396 0.357,0.137 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-9 (CANH) - G132-20 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

44.CONNECT CONNECTOR
40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
NOTICE:

For vehicles with a navigation system (for navigation receiver type), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Center Airbag Sensor Assembly)".


a.
U170297E01
0.972,0.95 1.073,0.95 1.073,0.95 1.396,1.234 false 1.396,1.439 1.173,1.769 1.173,1.769 1.05,1.769 false 0.463,0.873 0.883,1.010 0.421,0.137 10 CANH 0.567,1.687 0.963,1.824 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.611,1.259 2.968,1.396 0.357,0.137 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-9 (CANH) - G132-20 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

NG

46.CONNECT CONNECTOR
41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)
a.
U170298E01
2.404,0.783 2.303,0.783 2.303,0.783 1.842,1.234 false 1.842,1.439 2.126,1.842 2.126,1.842 2.249,1.842 false 2.422,0.705 2.843,0.842 0.421,0.137 10 CANH 2.26,1.76 2.656,1.897 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-5 (CANH) - G132-16 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NG

48.CONNECT CONNECTOR
42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)
a.
U170299E01
1.049,0.649 1.15,0.649 1.15,0.649 1.624,1.234 false 1.624,1.439 1.338,1.827 1.338,1.827 1.216,1.827 false 0.54,0.572 0.961,0.709 0.421,0.137 10 CANH 0.732,1.745 1.129,1.882 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.611,1.259 2.968,1.396 0.357,0.137 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-7 (CANH) - G132-18 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

50.CONNECT CONNECTOR
43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U170300E01
2.516,0.997 2.415,0.997 2.415,0.997 2.169,1.234 false 2.169,1.439 2.388,1.717 2.388,1.717 2.511,1.717 false 2.534,0.92 2.954,1.057 0.421,0.137 10 CANH 2.522,1.635 2.918,1.772 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-2 (CANH) - G132-13 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

52.CONNECT CONNECTOR
44.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

45.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)
45.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)
a.
U170265E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.598,0.371 1.872,0.512 0.274,0.140 10 H56 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H56-9 (CANH) - H56-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)

46.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

47.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)
47.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
U148880E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.58,0.371 1.854,0.512 0.274,0.140 10 H51 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H51-9 (CANH) - H51-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

48.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

49.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
49.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
a.
U148246E01
0.041,0 0.230,0.177 0.189,0.177 10 *a 0.132,1.336 0.551,1.513 0.419,0.177 10 CANH 0.295,0.987 0.560,1.164 0.266,0.177 10 G1 0.312,1.769 0.732,1.946 0.419,0.177 10 CANL 1.279,1.077 0.725,1.419 0.725,1.419 0.652,1.419 false 1.176,1.487 0.95,1.863 0.95,1.863 0.823,1.863 false

Disconnect the center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

50.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

51.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
51.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
a.
U148232E03
2.031,1.563 1.708,1.167 1.708,1.167 1.635,1.167 true 2.146,1.542 2.396,1.281 2.396,1.281 2.479,1.281 true 1.198,1.063 1.625,1.26 0.427,0.198 10 false CANH 0.875,1.427 1.198,1.625 0.323,0.198 10 false G33 0.083,0 0.51,0.198 0.427,0.198 10 false *a 2.51,1.198 2.927,1.396 0.417,0.198 10 false CANL

Disconnect the spiral cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G33-4 (CANH) - G33-3 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

52.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

53.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
53.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U148348E03
1.271,0.469 1.365,0.469 1.365,0.469 1.604,1.188 true 1.542,1.198 1.052,0.719 1.052,0.719 0.969,0.719 true 0.052,0 0.292,0.188 0.24,0.188 10 false *a 0.51,0.635 0.938,0.792 0.427,0.156 10 false CANH 0.844,0.385 1.25,0.542 0.406,0.156 10 false CANL 0.458,1.094 0.792,1.25 0.333,0.156 10 false G64

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G64-14 (CANH) - G64-13 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)