There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. | ·
Short between CAN bus lines and GND ·
Combination meter assembly ·
Master cylinder solenoid (skid control ECU) ·
Main body ECU (multiplex network body ECU) ·
Center airbag sensor assembly ·
Spiral cable sub-assembly (steering angle sensor) ·
Certification ECU (smart key ECU assembly) ·
Power management control ECU ·
Navigation receiver assembly*1 ·
Radio and display receiver assembly*2 ·
Four wheel drive control ECU ·
Power steering ECU assembly ·
Yaw rate sensor assembly ·
ECM ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 3 junction connector |
*1: w/ Navigation System (for Navigation Receiver Type)
*2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
NEXT
Disconnect the G132 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G48-6 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G48-14 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
Reconnect the G132 No. 2 junction connector.
NEXT
Disconnect the G134 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G48-6 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G48-14 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G134-5 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G134-16 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G134-4 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G134-15 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G134-3 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G134-14 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G134-8 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G134-19 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G134-6 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G134-17 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G134-2 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G134-13 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1GR-FE) | B |
| NG (for 1KD-FTV) | C |
| NG (for 1GD-FTV) | D |
A
B
C
D
Reconnect the G134 No. 3 junction connector.
NEXT
Disconnect the power steering ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G46-1 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G46-2 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Power Steering ECU Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G134 No. 3 junction connector.
NEXT
Disconnect the power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G51-14 (CA1H) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G51-13 (CA1L) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G134 No. 3 junction connector.
NEXT
Disconnect the four wheel drive control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G53-19 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G53-20 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Four Wheel Drive Control ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G134 No. 3 junction connector.
NEXT
Disconnect the yaw rate sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G52-3 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G52-2 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Yaw Rate Sensor Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G134 No. 3 junction connector.
NEXT
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G38-9 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G38-10 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G134 No. 3 junction connector.
NEXT
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G56-31 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G56-25 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to ECM) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G134 No. 3 junction connector.
NEXT
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G58-35 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G58-36 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to ECM) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G134 No. 3 junction connector.
NEXT
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G184-17 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G184-28 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to ECM) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G134 No. 3 junction connector.
NEXT
Disconnect the No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G132-1 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G132-12 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G132 No. 2 junction connector.
NEXT
Disconnect the A72 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G48-6 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G48-14 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A72-11 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| A72-22 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A72-10 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| A72-21 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A72 No. 1 junction connector.
NEXT
Disconnect the master cylinder solenoid (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A7-11 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| A7-25 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU]) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A72 No. 1 junction connector.
NEXT
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G6-40 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G6-39 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A72 No. 1 junction connector.
NEXT
Disconnect the No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G132-8 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G132-19 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without a navigation system (for navigation receiver type), go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Radio and Display Receiver Assembly)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G132-9 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G132-20 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles with a navigation system (for navigation receiver type), go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Center Airbag Sensor Assembly)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G132-9 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G132-20 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G132-5 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G132-16 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G132-7 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G132-18 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G132-2 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G132-13 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G132 No. 2 junction connector.
NEXT
Disconnect the navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H56-9 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| H56-10 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Navigation Receiver Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G132 No. 2 junction connector.
NEXT
Disconnect the radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H51-9 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| H51-10 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of DLC3 |
OK
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
NG
Reconnect the G132 No. 2 junction connector.
NEXT
Disconnect the center airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G1-13 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G1-22 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Center Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G132 No. 2 junction connector.
NEXT
Disconnect the spiral cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G33-4 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G33-3 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor]) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G132 No. 2 junction connector.
NEXT
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G64-14 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G64-13 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
| *b | Front view of DLC3 |
OK
NG