Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261034 CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)  Short to B+ in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
·

Short between CAN bus lines and +B

·

Combination meter assembly

·

Brake actuator assembly (skid control ECU)*1

·

Master cylinder solenoid (skid control ECU)*2

·

Main body ECU (multiplex network body ECU)

·

Center airbag sensor assembly

·

Spiral cable sub-assembly (steering angle sensor)*2

·

Radio and display receiver assembly*3

·

Four wheel drive control ECU

·

Air conditioning amplifier assembly

·

Power steering ECU assembly*4

·

Network gateway ECU*5

·

Yaw rate sensor assembly

·

ECM

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector



*1: w/o Vehicle Stability Control System

*2: w/ Vehicle Stability Control System (for Hydraulic Brake Booster)

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: for 1KD-FTV

*5: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type)


WIRING DIAGRAM

C292163E01
5.675,6.228 5.770,6.379 0.095,0.151 10 6 5.582,6.661 5.769,6.812 0.187,0.151 10 14 2.84,7.522 3.197,7.706 0.357,0.183 10 G132 2.84,7.67 4.467,7.827 1.627,0.157 10 No. 2 Junction Connector 5.881,0.627 6.305,0.781 0.423,0.153 10 CANH 5.881,1.262 6.305,1.408 0.423,0.147 10 CANL 5.658,1.551 6.018,1.724 0.359,0.173 10 G6 5.658,1.712 6.888,2.064 1.230,0.351 10 Combination Meter Assembly 3.92,0.627 4.108,0.778 0.187,0.151 10 10 3.92,1.066 4.108,1.217 0.187,0.151 10 21 3.92,2.506 4.108,2.657 0.187,0.151 10 9 3.92,2.928 4.108,3.079 0.187,0.151 10 20 3.92,4.376 4.108,4.527 0.187,0.151 10 8 3.92,4.798 4.108,4.949 0.187,0.151 10 19 3.08,0.627 3.258,0.778 0.178,0.151 10 11 3.08,1.066 3.268,1.217 0.187,0.151 10 22 3.172,4.376 3.269,4.527 0.097,0.151 10 2 3.08,4.798 3.268,4.949 0.187,0.151 10 13 3.92,6.228 4.108,6.379 0.187,0.151 10 4 3.92,6.661 4.108,6.812 0.187,0.151 10 15 3.172,6.228 3.269,6.379 0.097,0.151 10 5 3.08,6.651 3.268,6.801 0.187,0.151 10 16 0.898,1.184 1.293,1.321 0.396,0.136 10 CANL 0.87,0.73 1.293,0.867 0.423,0.136 10 CANH 1.411,0.627 1.599,0.778 0.187,0.151 10 25 1.411,1.066 1.599,1.217 0.187,0.151 10 14 0.353,1.551 0.710,1.734 0.357,0.183 10 A6 0.353,1.712 2.184,2.079 1.832,0.367 10 Brake Actuator Assembly (Skid Control ECU)*1 0.898,3.065 1.293,3.202 0.396,0.136 10 CANL 0.87,2.611 1.293,2.748 0.423,0.136 10 CANH 1.411,2.508 1.599,2.659 0.187,0.151 10 11 1.411,2.947 1.599,3.098 0.187,0.151 10 25 0.353,3.41 0.710,3.593 0.357,0.183 10 A7 0.353,3.569 2.184,3.935 1.832,0.367 10 Master Cylinder Solenoid (Skid Control ECU)*2 0.898,4.94 1.293,5.076 0.396,0.136 10 CANL 0.87,4.486 1.293,4.623 0.423,0.136 10 CANH 1.411,4.376 1.593,4.527 0.182,0.151 10 14 1.411,4.798 1.599,4.949 0.187,0.151 10 13 0.311,5.246 0.636,5.418 0.326,0.171 10 G64 0.311,5.397 1.976,5.727 1.665,0.330 10 Main Body ECU (Multiplex Network Body ECU) 5.881,6.793 6.277,6.929 0.396,0.136 10 CANL 5.881,6.339 6.305,6.475 0.423,0.136 10 CANH 0.898,6.793 1.293,6.929 0.396,0.136 10 CANL 0.87,6.339 1.293,6.475 0.423,0.136 10 CANH 1.411,6.229 1.593,6.379 0.182,0.151 10 13 1.411,6.651 1.599,6.801 0.187,0.151 10 22 0.319,7.099 0.645,7.271 0.326,0.171 10 G1 0.319,7.25 1.714,7.579 1.394,0.329 10 Center Airbag Sensor Assembly 0.174,8.015 3.965,8.164 3.790,0.149 10 *1: w/o Vehicle Stability Control System 0.174,8.323 4.506,8.472 4.332,0.149 10 *2: w/ Vehicle Stability Control System (for Hydraulic Brake Booster) 5.582,0.627 5.778,0.778 0.196,0.151 10 40 5.582,1.066 5.778,1.217 0.196,0.151 10 39 2.844,3.569 4.476,3.752 1.632,0.183 10 No. 1 Junction Connector 2.844,3.41 3.194,3.593 0.350,0.183 10 A72 6.056,7.263 6.434,7.453 0.379,0.190 10 DLC3 6.061,7.113 6.387,7.284 0.326,0.171 10 G48

C292164E01
5.675,0.743 5.770,0.894 0.095,0.151 10 4 5.675,1.176 5.770,1.327 0.095,0.151 10 3 3.92,1.747 4.108,1.898 0.187,0.151 10 1 3.92,2.169 4.108,2.320 0.187,0.151 10 12 5.32,1.767 7.043,2.130 1.723,0.363 10 Spiral Cable Sub-assembly (Steering Angle Sensor)*2 3.92,0.743 4.108,0.894 0.187,0.151 10 7 3.92,1.176 4.108,1.327 0.187,0.151 10 18 3.172,0.743 3.269,0.894 0.097,0.151 10 9 3.08,1.166 3.268,1.316 0.187,0.151 10 20 5.32,1.615 5.645,1.786 0.326,0.171 10 G33 5.881,1.308 6.277,1.444 0.396,0.136 10 CANL 5.881,0.854 6.305,0.990 0.423,0.136 10 CANH 0.898,1.308 1.293,1.444 0.396,0.136 10 CANL 0.87,0.854 1.293,0.990 0.423,0.136 10 CANH 1.411,0.743 1.593,0.894 0.182,0.151 10 9 1.411,1.166 1.599,1.316 0.187,0.151 10 10 0.319,1.614 0.645,1.785 0.326,0.171 10 H51 0.319,1.765 2.089,2.094 1.769,0.329 10 Radio and Display Receiver Assembly*3 1.428,3.602 1.614,3.753 0.186,0.151 10 19 1.428,4.048 1.614,4.198 0.186,0.151 10 20 3.914,3.602 4.102,3.753 0.187,0.151 10 1 3.914,4.057 4.102,4.208 0.187,0.151 10 12 3.914,5.495 4.102,5.646 0.187,0.151 10 4 3.914,5.94 4.102,6.091 0.187,0.151 10 15 5.603,5.495 5.784,5.646 0.181,0.151 10 11 5.591,5.94 5.778,6.091 0.187,0.151 10 12 1.439,5.495 1.621,5.646 0.181,0.151 10 1 1.428,5.94 1.615,6.091 0.187,0.151 10 2 3.159,3.602 3.269,3.753 0.110,0.151 10 3 3.087,4.048 3.274,4.198 0.187,0.151 10 14 2.801,2.655 3.158,2.838 0.357,0.183 10 G132 2.801,2.831 4.433,3.014 1.632,0.183 10 No. 2 Junction Connector 2.801,7.101 3.158,7.284 0.357,0.183 10 G134 2.801,7.277 4.433,7.460 1.632,0.183 10 No. 3 Junction Connector 0.279,4.525 0.676,4.691 0.396,0.166 10 G53 5.406,6.389 5.803,6.555 0.396,0.166 10 G25 5.406,6.557 7.021,6.887 1.615,0.330 10 Air Conditioning Amplifier Assembly 0.318,6.41 0.758,6.587 0.440,0.177 10 G46 0.318,6.572 1.640,6.941 1.322,0.369 10 Power Steering ECU Assembly*4 0.279,4.686 2.244,5.049 1.965,0.363 10 Four Wheel Drive Control ECU 3.159,5.495 3.291,5.645 0.132,0.150 10 5 3.087,5.941 3.274,6.091 0.187,0.151 10 16 0.901,3.716 1.324,3.853 0.423,0.137 10 CANH 0.901,4.167 1.324,4.304 0.423,0.137 10 CANL 0.901,5.598 1.324,5.735 0.423,0.137 10 CANH 0.901,6.049 1.324,6.186 0.423,0.137 10 CANL 5.879,5.598 6.302,5.735 0.423,0.137 10 CANH 5.873,6.049 6.297,6.186 0.423,0.137 10 CANL 0.254,8.085 4.186,8.248 3.932,0.163 10 *3: w/ Audio and Visual System (for Radio and Display Type) 0.254,8.399 4.186,8.563 3.932,0.163 10 *4: for 1KD-FTV 0.254,7.771 4.491,7.934 4.238,0.163 10 *2: w/ Vehicle Stability Control System (for Hydraulic Brake Booster)

C334434E01
5.418,2.723 5.743,2.877 0.324,0.154 10 36*4 5.413,2.258 5.748,2.411 0.334,0.153 10 35*4 5.425,2.485 5.736,2.624 0.310,0.139 10 G58 5.425,2.943 5.736,3.082 0.310,0.139 10 G58 4.963,2.723 5.287,2.877 0.324,0.154 10 31*6 4.958,2.258 5.292,2.411 0.334,0.153 10 25*6 4.945,2.485 5.305,2.624 0.359,0.139 10 G183 4.945,2.943 5.305,3.082 0.359,0.139 10 G183 3.914,2.393 4.102,2.544 0.187,0.151 10 2 3.914,2.834 4.102,2.985 0.187,0.151 10 13 1.288,2.383 1.424,2.533 0.136,0.150 10 3 1.288,2.828 1.402,2.979 0.115,0.151 10 2 3.159,2.383 3.291,2.533 0.132,0.150 10 8 3.087,2.834 3.274,2.985 0.187,0.151 10 19 1.288,0.409 1.514,0.559 0.227,0.150 10 16 1.288,0.854 1.477,1.005 0.189,0.151 10 15 0.177,3.288 0.535,3.472 0.357,0.183 10 G52 0.177,1.328 0.617,1.505 0.440,0.177 10 G155 0.177,1.49 2.055,1.859 1.878,0.369 10 Network Gateway ECU*5 3.159,0.409 3.291,0.559 0.132,0.150 10 6 3.087,0.854 3.274,1.005 0.187,0.151 10 17 5.873,2.375 6.297,2.528 0.423,0.153 10 CANH 5.873,3.02 6.297,3.167 0.423,0.147 10 CANL 6.022,3.294 6.376,3.460 0.354,0.166 10 ECM 2.801,3.277 3.158,3.460 0.357,0.183 10 G134 2.801,3.452 4.433,3.635 1.632,0.183 10 No. 3 Junction Connector 0.177,3.458 2.026,3.789 1.849,0.331 10 Yaw Rate Sensor Assembly 0.796,0.513 1.184,0.650 0.389,0.137 10 CA1H 0.817,0.964 1.185,1.101 0.368,0.137 10 CA1L 0.761,2.487 1.184,2.625 0.423,0.137 10 CANH 0.761,2.938 1.184,3.075 0.423,0.137 10 CANL 0.201,4.157 4.364,4.321 4.163,0.163 10 *5: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type) 0.198,3.874 1.408,4.037 1.210,0.163 10 *4: for 1KD-FTV 0.214,4.441 1.424,4.604 1.210,0.163 10 *6: for 5L-E

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
U148271E09
1.938,0.917 2.125,0.417 2.125,0.417 2.25,0.417 false 1.958,1.448 1.813,1.875 1.813,1.875 1.677,1.875 false 2.344,1.479 2.49,1.906 2.49,1.906 2.625,1.906 false 0.146,0.073 0.313,0.26 0.167,0.188 10 false *a 2.313,0.323 2.781,0.51 0.469,0.188 10 false CANH 1.229,1.771 1.635,1.958 0.406,0.188 10 false CANL 0.24,1.115 0.604,1.344 0.365,0.229 10 false G48 2.688,1.792 3,1.948 0.313,0.156 10 false BAT

Disconnect the G132 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G48-6 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G48-14 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of DLC3



OK

3.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

3.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR SIDE)
4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR SIDE)
a.
U148271E09
1.938,0.917 2.125,0.417 2.125,0.417 2.25,0.417 false 1.958,1.448 1.813,1.875 1.813,1.875 1.677,1.875 false 2.344,1.479 2.49,1.906 2.49,1.906 2.625,1.906 false 0.146,0.073 0.313,0.26 0.167,0.188 10 false *a 2.313,0.323 2.781,0.51 0.469,0.188 10 false CANH 1.229,1.771 1.635,1.958 0.406,0.188 10 false CANL 0.24,1.115 0.604,1.344 0.365,0.229 10 false G48 2.688,1.792 3,1.948 0.313,0.156 10 false BAT

Disconnect the G134 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G48-6 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G48-14 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of DLC3



OK

5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

25.CONNECT CONNECTOR
5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
NOTICE:

For vehicles with a 5L-E engine, go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - Air Conditioning Amplifier Assembly)".


a.
U170338E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.83,1.291 2.092,1.649 2.092,1.649 2.19,1.649 false 2.351,0.688 2.236,0.688 2.236,0.688 1.83,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.373,0.61 2.792,0.752 0.420,0.142 10 CANH 2.207,1.564 2.631,1.706 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 0.452,1.104 0.821,1.242 0.370,0.138 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-5 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G134-16 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

11.CONNECT CONNECTOR
6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U170339E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.933,1.291 2.172,1.677 2.172,1.677 2.269,1.677 false 2.351,0.756 2.236,0.756 2.236,0.756 1.933,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.373,0.679 2.792,0.821 0.420,0.142 10 CANH 2.287,1.591 2.711,1.733 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 0.452,1.104 0.821,1.242 0.370,0.138 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-4 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G134-15 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)

NG

13.CONNECT CONNECTOR
7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)
a.
U170340E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.015,1.291 2.182,1.649 2.182,1.649 2.28,1.649 false 2.426,0.797 2.311,0.797 2.311,0.797 2.015,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.448,0.72 2.868,0.862 0.420,0.142 10 CANH 2.297,1.564 2.721,1.706 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 0.452,1.104 0.821,1.242 0.370,0.138 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-3 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G134-14 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

NG

15.CONNECT CONNECTOR
8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)
a.
U170341E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.545,1.291 1.283,1.649 1.283,1.649 1.186,1.649 false 1.025,0.688 1.139,0.688 1.139,0.688 1.545,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.503,0.61 0.923,0.752 0.420,0.142 10 CANH 0.686,1.564 1.110,1.706 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 2.591,1.104 2.961,1.242 0.370,0.138 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-8 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G134-19 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

17.CONNECT CONNECTOR
9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
NOTICE:

For vehicles without a TOYOTA parking assist-sensor system (for 4 sensor type), go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - ECM)".


a.
U170342E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.732,1.291 1.433,1.686 1.433,1.686 1.336,1.686 false 1.132,0.608 1.247,0.608 1.247,0.608 1.732,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.634,0.531 1.054,0.673 0.420,0.142 10 CANH 0.834,1.6 1.258,1.742 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 2.557,1.104 2.927,1.242 0.370,0.138 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-6 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G134-17 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM)

NG

19.CONNECT CONNECTOR
10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM)
a.
U170343E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.118,1.291 2.292,1.561 2.292,1.561 2.389,1.561 false 2.449,0.877 2.335,0.877 2.335,0.877 2.118,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.471,0.799 2.891,0.941 0.420,0.142 10 CANH 2.407,1.475 2.831,1.617 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 0.452,1.104 0.821,1.242 0.370,0.138 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-2 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G134-13 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3

Result
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 5L-E) C



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

21.CONNECT CONNECTOR

C

23.CONNECT CONNECTOR
11.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)
12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)
a.
U148672E02
2.177,2.958 2.385,3.125 2.385,3.125 2.469,3.125 false 2.042,1.177 2.271,0.479 2.271,0.479 2.365,0.479 true 2.188,1.156 2.479,0.802 2.479,0.802 2.563,0.802 true 0.615,0.99 0.917,1.167 0.302,0.177 10 false G46 0.469,2.698 0.792,2.875 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.51,3.052 2.948,3.229 0.438,0.177 10 false BAT 2.583,0.708 3,0.885 0.417,0.177 10 false CANH 2.375,0.396 2.771,0.573 0.396,0.177 10 false CANL

Disconnect the G46 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G46-1 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G46-2 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

13.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U170103E01
2.301,2.817 2.515,3.053 2.515,3.053 2.565,3.053 false 0.103,1.907 0.298,2.071 0.196,0.164 10 *b 0.363,2.513 0.680,2.690 0.317,0.176 10 G48 2.604,2.961 2.959,3.138 0.355,0.176 10 BAT 0.11,0.051 0.291,0.256 0.181,0.205 10 *a 0.759,0.269 1.074,0.448 0.315,0.179 10 G25 1.851,1.104 2.076,0.238 2.076,0.238 2.206,0.238 false 1.977,1.106 2.352,0.535 2.352,0.535 2.482,0.535 false 2.234,0.151 2.676,0.356 0.442,0.205 10 CANH 2.497,0.433 2.938,0.637 0.442,0.205 10 CANL 1.851,1.104 2.076,0.238 2.076,0.238 2.206,0.238 false 1.977,1.106 2.352,0.535 2.352,0.535 2.482,0.535 false

Disconnect the G25 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G25-11 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G25-12 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

15.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU)
16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU)
a.
U148675E02
2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 true 0.979,1.042 0.896,0.5 0.896,0.5 0.802,0.5 true 0.875,1.052 0.594,0.688 0.594,0.688 0.51,0.688 true 2.844,1 3.125,1.177 0.281,0.177 10 false G53 0.469,2.719 0.792,2.896 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.542,2.99 2.875,3.167 0.333,0.177 10 false BAT 0.375,0.406 0.792,0.583 0.417,0.177 10 false CANH 0.104,0.615 0.5,0.792 0.396,0.177 10 false CANL

Disconnect the G53 four wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G53-19 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G53-20 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)
*b Front view of DLC3



OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)

17.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY)
18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY)
a.
U148667E02
2.188,2.958 2.396,3.125 2.396,3.125 2.479,3.125 true 1.583,1.26 1.302,0.292 1.302,0.292 1.208,0.292 true 1.448,1.25 0.948,0.708 0.948,0.708 0.854,0.708 true 0.406,1.219 0.708,1.396 0.302,0.177 10 false G52 0.448,2.729 0.771,2.906 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.521,3.042 2.958,3.219 0.438,0.177 10 false BAT 0.448,0.646 0.854,0.823 0.406,0.177 10 false CANL 0.792,0.208 1.208,0.385 0.417,0.177 10 false CANH

Disconnect the G52 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G52-3 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G52-2 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)

19.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NETWORK GATEWAY ECU)
20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NETWORK GATEWAY ECU)
a.
U170307E01
0.381,2.649 0.670,2.789 0.289,0.140 10 G48 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.326,1.193 1.227,1.641 1.227,1.641 1.13,1.641 false 0.958,1.391 1.03,1.391 1.03,1.391 1.21,1.191 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.478,1.319 0.897,1.461 0.420,0.142 10 CA1H 0.648,1.554 1.072,1.696 0.424,0.142 10 CA1L 2.523,3.123 2.947,3.265 0.424,0.142 10 BAT 2.601,1.058 2.971,1.198 0.370,0.140 10 G155

Disconnect the G155 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G155-16 (CA1H) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G155-15 (CA1L) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)

21.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
a.
U170187E01
0.433,2.643 0.721,2.821 0.287,0.178 10 G48 0.658,0.901 0.939,1.038 0.280,0.137 10 G58 0.062,0.016 0.275,0.194 0.213,0.178 10 *a 0.062,1.997 0.275,2.175 0.213,0.178 10 *b 2.525,2.987 2.958,3.165 0.434,0.178 10 BAT 2.229,2.918 2.434,3.082 2.434,3.082 2.521,3.082 false 0.755,1.842 1.186,1.979 0.431,0.137 10 CANH 1.327,1.462 1.168,1.68 1.168,1.68 1.081,1.68 false 0.589,1.599 1.020,1.737 0.431,0.137 10 CANL 1.444,1.462 1.368,1.927 1.368,1.927 1.28,1.927 false

Disconnect the G58 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G58-35 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G58-36 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

23.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
a.
U170538E02
2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 false 2.292,1.458 2.469,1.729 2.469,1.729 2.552,1.729 false 2.292,1.25 2.469,1.083 2.469,1.083 2.552,1.083 false 0.438,2.656 0.729,2.833 0.292,0.177 10 false G48 0.271,1.031 0.677,1.302 0.406,0.271 10 false G183 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.563,2.979 3,3.156 0.438,0.177 10 false BAT 2.594,1.635 3.104,1.927 0.51,0.292 10 false CANL 2.604,0.979 3.052,1.208 0.448,0.229 10 false CANH

Disconnect the G183 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G183-25 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G183-31 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

25.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U170344E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.221,1.291 2.395,1.561 2.395,1.561 2.492,1.561 false 2.553,0.877 2.438,0.877 2.438,0.877 2.221,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.575,0.799 2.994,0.941 0.420,0.142 10 CANH 2.51,1.475 2.934,1.617 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 0.452,1.104 0.821,1.242 0.370,0.138 10 G132

Disconnect the G132 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-1 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G132-12 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

27.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

27.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)
28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)
a.
U148271E09
1.938,0.917 2.125,0.417 2.125,0.417 2.25,0.417 false 1.958,1.448 1.813,1.875 1.813,1.875 1.677,1.875 false 2.344,1.479 2.49,1.906 2.49,1.906 2.625,1.906 false 0.146,0.073 0.313,0.26 0.167,0.188 10 false *a 2.313,0.323 2.781,0.51 0.469,0.188 10 false CANH 1.229,1.771 1.635,1.958 0.406,0.188 10 false CANL 0.24,1.115 0.604,1.344 0.365,0.229 10 false G48 2.688,1.792 3,1.948 0.313,0.156 10 false BAT

Disconnect the A72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G48-6 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G48-14 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of DLC3



OK

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)

NG

37.CONNECT CONNECTOR
29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)
a.
U170345E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.239,1.291 1.065,1.561 1.065,1.561 0.968,1.561 false 0.907,0.877 1.022,0.877 1.022,0.877 1.239,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.392,0.799 0.811,0.941 0.420,0.142 10 CANH 0.47,1.475 0.894,1.617 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 2.647,1.126 2.915,1.264 0.268,0.138 10 A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-11 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
A72-22 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3

Result
Result Proceed to
OK A
NG (w/o Vehicle Stability Control System) B
NG (w/ Vehicle Stability Control System [for Hydraulic Brake Booster]) C



A

30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

B

31.CONNECT CONNECTOR

C

33.CONNECT CONNECTOR
30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U170346E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.342,1.291 1.168,1.561 1.168,1.561 1.071,1.561 false 1.011,0.877 1.125,0.877 1.125,0.877 1.342,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.495,0.799 0.915,0.941 0.420,0.142 10 CANH 0.574,1.475 0.997,1.617 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 2.647,1.126 2.915,1.264 0.268,0.138 10 A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-10 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
A72-21 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

35.CONNECT CONNECTOR
31.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)
32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)
a.
U148737E01
0.235,0.911 0.520,1.089 0.285,0.178 10 A6 0.456,2.651 0.779,2.829 0.324,0.178 10 G48 0.069,0.016 0.282,0.194 0.213,0.178 10 *a 0.069,1.997 0.282,2.175 0.213,0.178 10 *b 2.532,2.987 2.965,3.165 0.434,0.178 10 BAT 2.236,2.918 2.44,3.082 2.44,3.082 2.528,3.082 false 1.657,1.652 2.091,1.830 0.434,0.178 10 CANH 1.303,1.297 1.566,1.747 1.566,1.747 1.654,1.747 false 1.644,0.188 2.077,0.366 0.434,0.178 10 CANL 1.314,1.089 1.553,0.283 1.553,0.283 1.64,0.283 false

Disconnect the A6 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A6-25 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
A6-14 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

33.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)
34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)
a.
U148661E02
2.219,2.948 2.417,3.115 2.417,3.115 2.51,3.115 true 2.146,0.906 2.385,0.229 2.385,0.229 2.469,0.229 true 2.146,1.031 2.656,0.479 2.656,0.479 2.74,0.479 true 0.271,0.958 0.552,1.135 0.281,0.177 10 false A7 0.479,2.698 0.802,2.875 0.323,0.177 10 false G48 0.073,0.021 0.281,0.198 0.208,0.177 10 false *a 0.073,2 0.281,2.177 0.208,0.177 10 false *b 2.552,3.021 2.99,3.198 0.438,0.177 10 false BAT 2.5,0.146 2.938,0.323 0.438,0.177 10 false CANH 2.76,0.385 3.198,0.563 0.438,0.177 10 false CANL

Disconnect the A7 master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A7-11 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
A7-25 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])
*b Front view of DLC3



OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

35.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
a.
U148676E02
2.208,2.948 2.417,3.115 2.417,3.115 2.5,3.115 true 0.906,1.156 1.417,0.167 1.417,0.167 1.51,0.167 true 1,1.167 1.708,0.365 1.708,0.365 1.792,0.365 true 0.344,0.969 0.635,1.146 0.292,0.177 10 false G6 0.448,2.677 0.771,2.854 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.531,3.031 2.969,3.208 0.438,0.177 10 false BAT 1.833,0.281 2.25,0.458 0.417,0.177 10 false CANL 1.531,0.083 2,0.26 0.469,0.177 10 false CANH

Disconnect the G6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G6-40 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G6-39 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

37.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U170347E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.545,1.291 1.283,1.649 1.283,1.649 1.186,1.649 false 1.025,0.688 1.139,0.688 1.139,0.688 1.545,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.503,0.61 0.923,0.752 0.420,0.142 10 CANH 0.686,1.564 1.110,1.706 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 2.591,1.104 2.961,1.242 0.370,0.138 10 G132

Disconnect the G132 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-8 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G132-19 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
NOTICE:

For vehicles without an audio and visual system (for radio and display type), go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Center Airbag Sensor Assembly)".


a.
U170348E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.442,1.291 1.189,1.624 1.189,1.624 1.091,1.624 false 0.99,0.774 1.105,0.774 1.105,0.774 1.442,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.469,0.696 0.889,0.838 0.420,0.142 10 CANH 0.592,1.538 1.015,1.680 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 2.591,1.104 2.961,1.242 0.370,0.138 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-9 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G132-20 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

NG

43.CONNECT CONNECTOR
40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)
a.
U170349E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.833,1.291 2.094,1.649 2.094,1.649 2.192,1.649 false 2.353,0.688 2.238,0.688 2.238,0.688 1.833,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.381,0.61 2.801,0.752 0.420,0.142 10 CANH 2.211,1.564 2.635,1.706 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 0.473,1.104 0.843,1.242 0.370,0.138 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-5 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G132-16 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NG

45.CONNECT CONNECTOR
41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)
NOTICE:

For vehicles without a vehicle stability control system (for hydraulic brake booster), go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Main Body ECU)".


a.
U170350E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.631,1.291 1.318,1.684 1.318,1.684 1.22,1.684 false 1.059,0.653 1.174,0.653 1.174,0.653 1.631,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.538,0.576 0.958,0.718 0.420,0.142 10 CANH 0.72,1.598 1.144,1.740 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 2.591,1.104 2.961,1.242 0.370,0.138 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-7 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G132-18 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

42.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

47.CONNECT CONNECTOR
42.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U170351E01
2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.122,1.291 2.283,1.566 2.283,1.566 2.38,1.566 false 2.411,0.89 2.296,0.89 2.296,0.89 2.122,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.433,0.812 2.853,0.954 0.420,0.142 10 CANH 2.398,1.48 2.822,1.622 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 0.452,1.104 0.821,1.242 0.370,0.138 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-2 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G132-13 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

49.CONNECT CONNECTOR
43.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

44.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)
44.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
U170267E01
0.378,2.688 0.659,2.828 0.281,0.140 10 G48 1.529,0.311 1.806,0.451 0.276,0.140 10 H51 0.088,0.077 0.353,0.219 0.265,0.142 10 *a 0.088,0.077 0.353,0.219 0.265,0.142 10 *a 0.088,1.765 0.353,1.907 0.265,0.142 10 *b 2.394,1.689 2.282,1.689 2.282,1.689 1.983,1.175 false 1.444,1.689 1.556,1.689 1.556,1.689 1.856,1.175 false 0.913,1.6 1.356,1.740 0.443,0.140 10 CANH 2.421,1.6 2.864,1.740 0.443,0.140 10 CANL 2.184,2.927 2.316,3.148 2.316,3.148 2.456,3.148 false 2.486,3.05 2.909,3.192 0.424,0.142 10 BAT

Disconnect the H51 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H51-9 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
H51-10 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

45.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

46.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
46.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
a.
U148679E01
2.874,0.879 3.180,1.057 0.305,0.178 10 G1 0.449,2.651 0.772,2.829 0.324,0.178 10 G48 0.062,0.016 0.275,0.194 0.213,0.178 10 *a 0.062,1.997 0.275,2.175 0.213,0.178 10 *b 2.525,2.987 2.958,3.165 0.434,0.178 10 BAT 2.229,2.918 2.434,3.082 2.434,3.082 2.521,3.082 false 0.379,0.178 0.792,0.356 0.413,0.178 10 CANH 1.196,1.396 1.093,1.711 1.093,1.711 1.005,1.711 false 0.523,1.632 0.919,1.810 0.396,0.178 10 CANL 1.331,0.918 0.992,0.257 0.992,0.257 0.904,0.257 false

Disconnect the G1 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G1-13 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G1-22 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

47.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

48.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)
48.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)
a.
U170182E02
1.771,1.042 1.521,0.292 1.521,0.292 1.438,0.292 true 1.667,1.083 1.292,0.573 1.292,0.573 1.208,0.573 true 2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 true 0.75,0.906 1.052,1.083 0.302,0.177 10 false G33 0.771,0.49 1.177,0.667 0.406,0.177 10 false CANH 1.021,0.219 1.417,0.396 0.396,0.177 10 false CANL 0.427,2.667 0.75,2.844 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.521,2.99 2.958,3.167 0.438,0.177 10 false BAT

Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G33-4 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G33-3 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])
*b Front view of DLC3



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

49.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

50.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)
50.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)
a.
U148664E02
2.208,2.938 2.417,3.104 2.417,3.104 2.5,3.104 true 1.604,1.104 1.385,0.344 1.385,0.344 1.302,0.344 true 1.542,1.125 1.135,0.563 1.135,0.563 1.052,0.563 true 0.51,1.01 0.854,1.188 0.344,0.177 10 false G64 0.448,2.698 0.771,2.875 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.521,3.031 2.958,3.208 0.438,0.177 10 false BAT 0.583,0.49 1.01,0.667 0.427,0.177 10 false CANH 0.875,0.271 1.271,0.448 0.396,0.177 10 false CANL

Disconnect the G64 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G64-14 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G64-13 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)