1.INSTALL WIRE HARNESS CLAMP BRACKET
It is not necessary to remove the wire harness clamp brackets unless they are being replaced.
Attach the 8 wire harness clamps and claw and install the 4 wire harness clamp brackets to the wire harness.
w/o ATF Warmer:
Install the wire harness clamp bracket to the automatic transmission assembly with the bolt.
2.INSTALL TORQUE CONVERTER ASSEMBLY
Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly (*a) and the torque converter assembly contact surface of the drive plate (*b).
| *a | Engine Surface |
| *b | Drive Plate Surface |
Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.
| *a | Matchmark |
Install the torque converter assembly to the input shaft while keeping it horizontal.
Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.
| *1 | Front Oil Pump Oil Seal |
Do not damage the front oil pump oil seal.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the automatic transmission case sub-assembly and insert the key of the torque converter assembly into the groove of the oil pump drive gear.
| *1 | Front Oil Pump Oil Seal |
Do not push the torque converter assembly excessively when rotating it.
Do not damage the front oil pump oil seal.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.
B = A + 1 mm (0.0394 in.) or more
Make sure to deduct the thickness of the straightedge.
If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
3516A
3.INSTALL TRANSMISSION OIL PAN HEAT INSULATOR
It is not necessary to remove the transmission oil pan heat insulator unless it is being replaced.
Install the transmission oil pan heat insulator to the automatic transmission assembly with the 3 bolts.
33823
4.INSTALL TRANSMISSION CONTROL CABLE BRACKET
It is not necessary to remove the transmission control cable bracket unless it is being replaced.
Install the transmission control cable bracket to the automatic transmission assembly with the 2 bolts.
36100
5.INSTALL TRANSFER ASSEMBLY
33490F
6.INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ ATF Warmer)
Make sure to install the clips so that the spool fitting is not overlapped.
It is not necessary to remove the transmission oil cooler assembly unless it is being replaced.
Temporarily install the transmission oil cooler assembly to the automatic transmission assembly with the bolt labeled A. Install the bolt labeled B and bolt labeled C tighten it to the specified torque. Then tighten the bolt labeled A to the specified torque.
| *a | 2 to 7 mm (0.0788 to 0.2755 in.) |
Connect the 2 oil cooler hoses to the automatic transmission assembly, and slide the 2 clips to secure them.
Make sure to install any hose clips without a specific installation direction in a direction that does not interfere with other parts.
35000
7.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz.)
| *1 | Crankshaft |
| *2 | Torque Converter Assembly Centerpiece |
|
Clutch Spline Grease |
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
While keeping the engine assembly and automatic transmission assembly horizontal, align the 2 knock pins with the holes in the automatic transmission assembly and install the 9 bolts.
Do not use excessive force when installing the automatic transmission assembly.
Check that the torque converter assembly rotates.
Make sure that the wire harness or other similar items are not pinched between the contact surfaces.
Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.
Connect the breather hose to the engine assembly.
8.CONNECT WIRE HARNESS
Tilt down the automatic transmission assembly.
Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.
Connect the wire harness to the automatic transmission assembly with the 4 bolts.
Attach the 2 wire harness clamps.
Attach the heated oxygen sensor connector to the wire harness clamp bracket.
Connect the park/neutral position switch connector, transmission wire connector, 2 transmission revolution sensor connectors and transfer connector.
Push up the lever until the claw of the transmission wire connector makes a connection sound.
Connect the breather hose to the wire harness.
36478A
9.INSTALL TRANSMISSION BREATHER BRACKET
Install the clamp to the transmission breather bracket.
It is not necessary to remove the transmission breather clamp unless it is being replaced.
Install the transmission breather bracket to the automatic transmission assembly with the bolt.
Connect the 2 breather hoses and attach the wire harness clamp to the transmission breather bracket.
12371
10.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
Install the rear No. 1 engine mounting insulator to the automatic transmission assembly with the 4 bolts.
Make sure to install the engine mounting heat insulator so that its installation surface faces the right side of the vehicle.
Install the engine mounting heat insulator to the rear No. 1 engine mounting insulator with the bolt.
51203
11.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Install the No. 3 frame crossmember sub-assembly to the body with the 4 bolts and 4 nuts.
Install the nuts so that they face the rear of the vehicle.
Hold the bolts while tightening the nuts.
Connect the No. 3 frame crossmember sub-assembly to the rear No. 1 engine mounting insulator with the 4 bolts.
51226A
12.INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH
Install the front suspension member bracket LH and RH with the 8 bolts.
13.CONNECT WATER BY-PASS PIPE (w/ ATF Warmer)
Make sure to install the clips so that the spool fitting is not overlapped.
Connect the water by-pass pipe to the automatic transmission assembly with the 2 bolts.
| *a | RH Side |
| *b | 2 to 7 mm (0.0788 to 0.2755 in.) |
Connect the 2 water by-pass hoses to the transmission oil cooler assembly, and slide the 2 clips to secure them.
14.CONNECT OIL COOLER TUBE (w/ ATF Warmer)
Connect the 2 oil cooler tubes to the automatic transmission assembly and engine assembly with the 2 bolts.
Connect the 2 oil cooler hoses to the transmission oil cooler assembly, and slide the 2 clips to secure them.
| *a | Front Side |
| *b | Lower Side |
| *c | 2 to 7 mm (0.0788 to 0.2755 in.) |
15.CONNECT OIL COOLER TUBE (w/o ATF Warmer)
Connect the ends of the 2 oil cooler tubes to the automatic transmission assembly by hand.
Connect the 2 oil cooler tubes to the automatic transmission assembly and engine assembly with the 2 bolt.
Using a 17 mm union nut wrench, tighten the 2 oil cooler tubes.
| *a | Torque Wrench Fulcrum Length |
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
(See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)
When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 29 N*m (300 kgf*cm, 22 ft.*lbf)
35979B
16.INSTALL TRANSMISSION INSULATOR RH
33820B
17.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Turn the control shaft lever clockwise until it stops, and then return the control shaft lever counterclockwise 2 notches to N.
Move the shift lever to N, and with the cable end lightly pushed toward the rear of the vehicle, install the transmission control cable assembly to the transmission control shaft lever LH with the nut.
Tighten the nut with no slack in the transmission control cable assembly.
Connect the transmission control shift cable assembly to the transmission control cable bracket with a new clip.
32101A
18.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.
Install the black colored bolt first, and then the remaining 5 silver colored bolts.
11363A
19.INSTALL FLYWHEEL HOUSING SIDE COVER
Install the flywheel housing side cover to the engine assembly.
28100
20.INSTALL STARTER ASSEMBLY
17105
21.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH
17104
22.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH
37110
23.INSTALL PROPELLER SHAFT ASSEMBLY
37140
24.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
17129
25.INSTALL INTAKE AIR SURGE TANK
26.ADD AUTOMATIC TRANSMISSION FLUID
27.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
28. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
(See pageGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE)
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
(See pageGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART)
29.ADD ENGINE COOLANT (w/ ATF Warmer)
30.INSPECT SHIFT LEVER POSITION
31.ADJUST AUTOMATIC TRANSMISSION FLUID
32.INSPECT FOR COOLANT LEAK
33.INSPECT FOR EXHAUST GAS LEAK
34.INSPECT FOR OIL LEAK
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
51450
35.INSTALL REAR ENGINE UNDER COVER ASSEMBLY
51405A
36.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
37. RESET MEMORY
If automatic transmission parts have been replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.