2011-2013 Land Cruiser · Service Manual Power Source / Network

U1002 (CAN No. 2 BUS) Lost Communication with Gateway Module (Network Gateway ECU)

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

  1. The network gateway ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN movement control bus.
  2. When the network gateway ECU receives a response signal from the ECUs connected to the CAN movement control bus, the network gateway ECU recognizes and memorizes that the ECU is connected to the CAN movement control bus. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to the CAN movement control bus when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN movement control bus, the network gateway ECU determines that a malfunction exists.
  3. If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
DTC Code
Symptoms
Trouble Area
U1002 (CAN No. 2 BUS)
Lost communication with the gateway module (network gateway ECU).
  1. Movement control bus circuit
  2. 4WD control ECU CAN branch wire or connector
  3. Power steering ECU assembly CAN branch wire or connector*1
  4. Yaw rate sensor assembly CAN branch wire or connector*2
  5. Distance control ECU assembly CAN branch wire or connector*3
  6. Seat belt control ECU CAN branch wire or connector*4
  7. Parking assist ECU CAN branch wire or connector*5
  8. Clearance warning ECU assembly CAN branch wire or connector*6
  9. Master cylinder solenoid (skid control ECU) CAN branch wire or connector
  10. Steering angle sensor CAN branch wire or connector*2
  11. Network gateway ECU CAN main wire or connector
  12. Steering control ECU CAN branch wire or connector*7
  13. Suspension control ECU CAN branch wire or connector*8
  14. 4WD control ECU
  15. Power steering ECU assembly*1
  16. Yaw rate sensor assembly*2
  17. Distance control ECU assembly*3
  18. Seat belt control ECU*4
  19. Parking assist ECU*5
  20. Clearance warning ECU assembly*6
  21. Master cylinder solenoid (skid control ECU)
  22. Steering angle sensor*2
  23. Steering control ECU*7
  24. Suspension control ECU*8
  25. Network gateway ECU
  26. No. 4 junction connector
  27. No. 5 junction connector
  28. No. 6 junction connector
  29. No. 7 junction connector
  30. No. 1 CAN junction connector
  1. *1: for 1VD-FTV with DPF
  2. *2: w/ Vehicle Stability Control System
  3. *3: w/ Dynamic Radar Cruise Control System
  4. *4: w/ Pre-crash Safety System
  5. *5: w/ Side Monitor System
  6. *6: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System
  7. *7: w/ Variable Gear Ratio Steering System
  8. *8: w/ Active Height Control Suspension System
  9. For vehicles with a network gateway ECU.

WIRING DIAGRAM

C259247E01
C259248E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT CIRCUIT)
C242747E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance Malfunction
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    54 to 69 Ω
    70 Ω or higher: Open in CAN main bus line
    E31-13 (CA2H) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E31-12 (CA2L) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E31-13 (CA2H) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    E31-12 (CA2L) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)
    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main wire
    A
    NG
    1. Short in line
    2. +B short
    3. Ground short
    B
    OK
    C



B
Go to step 19

C
Go to step 69
A


4. CHECK FOR OPEN IN MAIN BUS WIRE (NO. 7 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. E211920E13
    Disconnect the E74 No. 7 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-2 (CANH) - E74-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)



NG
Go to step 6
OK


5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

  1. E211920E14
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-1 (CANH) - E74-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)



NG
Go to step 15
OK

REPLACE NO. 7 JUNCTION CONNECTOR

6. CONNECT CONNECTOR
  1. Reconnect the E74 No. 7 junction connector.


NEXT


7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

  1. E211920E15
    Disconnect the F73 No. 6 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F73-6 (CANH) - F73-17 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
OK


8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. E211920E16
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F73-7 (CANH) - F73-18 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)



NG
Go to step 9
OK

REPLACE NO. 6 JUNCTION CONNECTOR

9. CONNECT CONNECTOR
  1. Reconnect the F73 No. 6 junction connector.


NEXT


10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. E211920E17
    Disconnect the E68 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E68-2 (CANH) - E68-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK


11. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. E211920E18
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E68-1 (CANH) - E68-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
Go to step 12
OK

REPLACE NO. 5 JUNCTION CONNECTOR

12. CONNECT CONNECTOR
  1. Reconnect the E68 No. 5 junction connector.


NEXT


13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

  1. E211920E19
    Disconnect the E71 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E71-1 (CANH) - E71-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK


14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. E211920E20
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E71-2 (CANH) - E71-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
Go to step 17
OK

REPLACE NO. 4 JUNCTION CONNECTOR

15. CONNECT CONNECTOR
  1. Reconnect the E74 No. 7 junction connector.


NEXT


16. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

  1. C259623E01
    Disconnect the K29 No. 1 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    K29-1 (CANH) - K29-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

17. CONNECT CONNECTOR
  1. Reconnect the E71 No. 4 junction connector.


NEXT


18. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NETWORK GATEWAY ECU - NO. 4 JUNCTION CONNECTOR)

  1. C242749E12
    Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (NETWORK GATEWAY ECU - NO. 4 JUNCTION CONNECTOR)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR SIDE)

  1. C242747E04
    Disconnect the E74 No. 7 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    E31-13 (CA2H) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    E31-12 (CA2L) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    E31-13 (CA2H) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    E31-12 (CA2L) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)



NG
Go to step 24
OK


20. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - STEERING CONTROL ECU)

NOTICE:
For vehicles without a variable gear ratio steering system, go to "Check for Short in CAN Bus Wires (No. 7 Junction Connector - Steering Angle Sensor)".

  1. C259545E39
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-3 (CANH) - E74-14 (CANL)
    Ignition switch off
    200 Ω or higher
    E74-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E74-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 40
OK


21. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NOTICE:
For vehicles without a vehicle stability control system, go to "Check for Short in CAN Bus Wires (No. 7 Junction Connector - Skid Control ECU)".

  1. C259545E40
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-4 (CANH) - E74-15 (CANL)
    Ignition switch off
    200 Ω or higher
    E74-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E74-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 42
OK


22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C259545E41
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-5 (CANH) - E74-16 (CANL)
    Ignition switch off
    200 Ω or higher
    E74-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E74-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 44
OK


23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

  1. C259545E42
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-1 (CANH) - E74-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    E74-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E74-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Active Height Control Suspension)
    B
    NG (w/o Active Height Control Suspension)
    C



B
Go to step 46

C
Go to step 51
A

REPLACE NO. 7 JUNCTION CONNECTOR

24. CONNECT CONNECTOR
  1. Reconnect the E74 No. 7 junction connector.


NEXT


25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

  1. C259545E43
    Disconnect the F73 No. 6 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F73-6 (CANH) - F73-17 (CANL)
    Ignition switch off
    108 to 132 Ω
    F73-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F73-17 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F73-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F73-17 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
OK


26. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)

  1. C242747E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    E31-13 (CA2H) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    E31-12 (CA2L) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    E31-13 (CA2H) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    E31-12 (CA2L) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)
    Result 
    Result
    Proceed to
    OK (w/o TOYOTA Parking Assist-sensor System and w/o Side Monitor System)
    A
    OK (w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System)
    B
    OK (w/ Side Monitor System)
    C
    NG
    D



B
Go to step 27

C
Go to step 28

D
Go to step 29
A

REPLACE NO. 6 JUNCTION CONNECTOR

27. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

  1. C259545E44
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F73-5 (CANH) - F73-16 (CANL)
    Ignition switch off
    200 Ω or higher
    F73-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F73-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F73-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F73-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 53
OK

REPLACE NO. 6 JUNCTION CONNECTOR

28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - PARKING ASSIST ECU)

  1. C259545E44
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F73-5 (CANH) - F73-16 (CANL)
    Ignition switch off
    200 Ω or higher
    F73-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F73-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F73-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F73-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 6 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 55
OK

REPLACE NO. 6 JUNCTION CONNECTOR

29. CONNECT CONNECTOR
  1. Reconnect the F73 No. 6 junction connector.


NEXT


30. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. C259545E45
    Disconnect the E68 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E68-2 (CANH) - E68-13 (CANL)
    Ignition switch off
    108 to 132 Ω
    E68-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E68-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK


31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR SIDE)

  1. C242747E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    E31-13 (CA2H) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    E31-12 (CA2L) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    E31-13 (CA2H) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    E31-12 (CA2L) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)



NG
Go to step 35
OK


32. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - DISTANCE CONTROL ECU ASSEMBLY)

NOTICE:
For vehicles without a dynamic radar cruise control system, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - Seat Belt Control ECU)".

  1. C259545E46
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E68-4 (CANH) - E68-15 (CANL)
    Ignition switch off
    200 Ω or higher
    E68-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E68-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 57
OK


33. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)

NOTICE:
For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - Yaw Rate Sensor Assembly)".

  1. C259545E47
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E68-5 (CANH) - E68-16 (CANL)
    Ignition switch off
    200 Ω or higher
    E68-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E68-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 59
OK


34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

NOTICE:
For vehicles without a vehicle stability control system, replace No. 5 junction connector.

  1. C259545E48
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E68-3 (CANH) - E68-14 (CANL)
    Ignition switch off
    200 Ω or higher
    E68-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E68-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 61
OK

REPLACE NO. 5 JUNCTION CONNECTOR

35. CONNECT CONNECTOR
  1. Reconnect the E68 No. 5 junction connector.


NEXT


36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

  1. C259545E49
    Disconnect the E71 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E71-1 (CANH) - E71-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    E71-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E71-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E71-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E71-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for 1VD-FTV with DPF)
    A
    OK (except 1VD-FTV with DPF)
    B
    NG
    C



B
Go to step 38

C
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
A


37. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

  1. C259545E50
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E71-4 (CANH) - E71-15 (CANL)
    Ignition switch off
    200 Ω or higher
    E71-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E71-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E71-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E71-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 63
OK


38. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU)

  1. C259545E51
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E71-3 (CANH) - E71-14 (CANL)
    Ignition switch off
    200 Ω or higher
    E71-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E71-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E71-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E71-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 65
OK


39. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. C259545E52
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E71-2 (CANH) - E71-13 (CANL)
    Ignition switch off
    108 to 132 Ω
    E71-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E71-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E71-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E71-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 67
OK

REPLACE NO. 4 JUNCTION CONNECTOR

40. CONNECT CONNECTOR
  1. Reconnect the E74 No. 7 junction connector.


NEXT


41. CHECK FOR SHORT IN CAN BUS WIRES (STEERING CONTROL ECU)

  1. C238565E03
    Disconnect the E79 steering control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E79-9 (CANH) - E79-20 (CANL)
    Ignition switch off
    54 to 69 Ω
    E79-9 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E79-20 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E79-9 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E79-20 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Steering Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING CONTROL ECU (CANH, CANL)
OK

REPLACE STEERING CONTROL ECU (Click here)

42. CONNECT CONNECTOR
  1. Reconnect the E74 No. 7 junction connector.


NEXT


43. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)

  1. C259519E01
    Disconnect the E11 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E11-10 (CANH) - E11-9 (CANL)
    Ignition switch off
    54 to 69 Ω
    E11-10 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E11-9 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E11-10 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E11-9 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR (Click here)

44. CONNECT CONNECTOR
  1. Reconnect the E74 No. 7 junction connector.


NEXT


45. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)

  1. C259520E01
    Disconnect the A24 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-11 (CANH) - A24-25 (CANL)
    Ignition switch off
    54 to 69 Ω
    A24-11 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    A24-25 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    A24-11 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A24-25 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid [Skid Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

46. CONNECT CONNECTOR
  1. Reconnect the E74 No. 7 junction connector.


NEXT


47. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)

  1. C259624E01
    Disconnect the K39 No. 1 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    K39-1 (CANH) - K39-2 (CANL)
    Ignition switch off
    200 Ω or higher
    K39-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    K39-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    K39-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    K39-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 49
OK


48. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)

  1. C259624E02
    Disconnect the K29 No. 1 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    K29-1 (CANH) - K29-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    K29-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    K29-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    K29-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    K29-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

49. CONNECT CONNECTOR
  1. Reconnect the K39 No. 1 CAN junction connector.


NEXT


50. CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)

  1. C259521E01
    Disconnect the K34 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    K34-7 (CANH) - K34-8 (CANL)
    Ignition switch off
    54 to 69 Ω
    K34-7 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    K34-8 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    K34-7 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    K34-8 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Suspension Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)

51. CONNECT CONNECTOR
  1. Reconnect the E74 No. 7 junction connector.


NEXT


52. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)

  1. C259624E02
    Disconnect the K29 No. 1 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    K29-1 (CANH) - K29-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    K29-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    K29-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    K29-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    K29-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

53. CONNECT CONNECTOR
  1. Reconnect the F73 No. 6 junction connector.


NEXT


54. CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

  1. C259522E01
    Disconnect the F12 clearance warning ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F12-3 (CANH) - F12-5 (CANL)
    Ignition switch off
    54 to 69 Ω
    F12-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F12-5 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F12-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F12-5 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Clearance Warning ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)

55. CONNECT CONNECTOR
  1. Reconnect the F73 No. 6 junction connector.


NEXT


56. CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)

  1. C259523E01
    Disconnect the F76 parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F76-40 (CANH) - F76-39 (CANL)
    Ignition switch off
    54 to 69 Ω
    F76-40 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F76-39 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    F76-40 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F76-39 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Parking Assist ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO PARKING ASSIST ECU (CANH, CANL)
OK

REPLACE PARKING ASSIST ECU (Click here)

57. CONNECT CONNECTOR
  1. Reconnect the E68 No. 5 junction connector.


NEXT


58. CHECK FOR SHORT IN CAN BUS WIRES (DISTANCE CONTROL ECU ASSEMBLY)

  1. C217226E11
    Disconnect the E108 distance control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E108-8 (CANH) - E108-9 (CANL)
    Ignition switch off
    54 to 69 Ω
    E108-8 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E108-9 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E108-8 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E108-9 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Distance Control ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DISTANCE CONTROL ECU ASSEMBLY (CANH, CANL)
OK

REPLACE DISTANCE CONTROL ECU ASSEMBLY (Click here)

59. CONNECT CONNECTOR
  1. Reconnect the E68 No. 5 junction connector.


NEXT


60. CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)

  1. C259524E01
    Disconnect the E42 seat belt control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E42-1 (CANH) - E42-2 (CANL)
    Ignition switch off
    54 to 69 Ω
    E42-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E42-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E42-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E42-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Seat Belt Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SEAT BELT CONTROL ECU (CANH, CANL)
OK

REPLACE SEAT BELT CONTROL ECU (Click here)

61. CONNECT CONNECTOR
  1. Reconnect the E68 No. 5 junction connector.


NEXT


62. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)

  1. C259525E01
    Disconnect the E50 yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E50-3 (CANH) - E50-2 (CANL)
    Ignition switch off
    54 to 69 Ω
    E50-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E50-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E50-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E50-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)

63. CONNECT CONNECTOR
  1. Reconnect the E71 No. 4 junction connector.


NEXT


64. CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)

  1. C242957E05
    Disconnect the E102 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E102-1 (CANH) - E102-2 (CANL)
    Ignition switch off
    54 to 69 Ω
    E102-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E102-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E102-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E102-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)

65. CONNECT CONNECTOR
  1. Reconnect the E71 No. 4 junction connector.


NEXT


66. CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)

  1. C259514E02
    Disconnect the A27 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A27-19 (CAN+) - A27-20 (CAN-)
    Ignition switch off
    54 to 69 Ω
    A27-19 (CAN+) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    A27-20 (CAN-) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    A27-19 (CAN+) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A27-20 (CAN-) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to 4WD Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CAN+, CAN-)
OK

REPLACE 4WD CONTROL ECU (Click here)

67. CONNECT CONNECTOR
  1. Reconnect the E71 No. 4 junction connector.


NEXT


68. CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)

  1. C251426E03
    Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    E31-13 (CA2H) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E31-12 (CA2L) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E31-13 (CA2H) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E31-12 (CA2L) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (CA2H, CA2L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

69. CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)

  1. C242749E11
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-4 (GND) - Body ground
    Ignition switch off
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E31-2 (BATT) - Body ground
    Always
    11 to 14 V
    E31-9 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V
    E31-10 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Network Gateway ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NETWORK GATEWAY ECU (Click here)


← U1002 (CAN No. 2 BUS) Lost Communication with Gateway Module (Network Gateway ECU) (Sep 2011 – Dec 2011)U1100 Lost Communication with Seat Belt Control ECU (Sep 2011 – Dec 2011) →