Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  Black Smoke Emitted  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing a fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing a fuel injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


PROCEDURE

1.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.


d.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
DTCs related to the engine are output B



A

2.READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #8)

B

REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT

2.READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #8)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List.


d.

Select the following menu items in order and read the values.

·

Injection Volume

·

Injection Feedback Val #1, #2, #3, #4, #5, #6, #7 and #8


Standard Value:
Item Engine Speed* Reference Value
Injection Volume Idling (No engine load) 3.0 to 10 mm3/st
Injection Feedback Val #1 to #8 Idling (No engine load) -3.0 to 3.0 mm3/st


HINT:

*: If no idling conditions are specified, the shift lever should be in N, and the A/C switch and all accessory switches should be off.




OK

3.PERFORM ENGINE SPEED ACCELERATION

NG

11.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
3.PERFORM ENGINE SPEED ACCELERATION
HINT:

If the exhaust gas contains excessive black smoke, perform the following operations.


a.

Accelerate the engine to the maximum speed with no load 20 times.


b.

Check the volume of black smoke in the exhaust gas.

Result
Result Proceed to
Black smoke is not present OK
Black smoke remains in the exhaust gas NG

HINT:

Soot deposits in the exhaust system may cause excessive black smoke.




OK

END

NG

4.CHECK INTAKE AIR CONTROL SYSTEM AND EXHAUST SYSTEM
4.CHECK INTAKE AIR CONTROL SYSTEM AND EXHAUST SYSTEM

OK

5.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

5.INSPECT MASS AIR FLOW METER

OK

6.CHECK TURBOCHARGING PRESSURE

NG

6.CHECK TURBOCHARGING PRESSURE
a.

Check the turbocharging pressure (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

The turbocharger pressure is within the standard range.




OK

7.READ VALUE USING INTELLIGENT TESTER (DATA LIST)

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2)

7.READ VALUE USING INTELLIGENT TESTER (DATA LIST)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List.


d.

Select the following menu items in order and read the values.

·

Fuel Press

·

Injection Volume

·

Main Injection Period

·

Pilot 2 Injection Period

·

Injection Feedback Val #1, #2, #3, #4, #5, #6, #7 and #8


Reference:
Item Engine Speed* Reference Value
Fuel Press Idling 27 to 37 MPa
Fuel Press 2000 rpm (no engine load) 50 to 70 MPa
Fuel Press 3000 rpm (no engine load) 52 to 76 MPa
Injection Volume Idling 3.0 to 10 mm3/st
Injection Volume 2000 rpm (no engine load) 3.5 to 11 mm3/st
Injection Volume 3000 rpm (no engine load) 6.5 to 13 mm3/st
Main Injection Period Idling 430 to 730 μs
Pilot 2 Injection Period Idling 390 to 490 μs
Injection Feedback Val #1 to #8 Idling -3.0 to 3.0 mm3


HINT:

*: If no idling conditions are specified, the shift lever should be in N, and the A/C switch and all accessory switches should be off.


Result
Result Proceed to
Within reference value A
One of Injection Feedback Val #1 to #8 is not within reference value B
Other result C



A

8.CHECK CYLINDER COMPRESSION PRESSURE

B

REPLACE MALFUNCTIONING FUEL INJECTOR

C

11.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
8.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).



OK

9.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - EDU)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

9.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - EDU)
A385207E01
1.146,0.875 1.521,1.104 0.375,0.229 1.75,0.885 2.125,1.115 0.375,0.229 2.344,0.885 2.719,1.115 0.375,0.229 2.927,0.885 3.302,1.115 0.375,0.229 4.917,0.917 5.333,1.156 0.417,0.24 4.281,2.052 4.552,1.802 true 4.542,2.094 4.677,1.802 true 4.802,2.104 4.844,1.823 true 5.177,2.115 5.021,1.802 true 5.49,2.104 5.177,1.802 true 5.948,2.104 5.333,1.802 true 0.802,0.115 3.115,0.51 2.313,0.396 10 false Front view of wire harness connector: (to Fuel injector) 1.24,0.906 1.552,1.104 0.313,0.198 10 false C5 1.823,0.917 2.135,1.115 0.313,0.198 10 false C14 2.417,0.917 2.729,1.115 0.313,0.198 10 false C69 2.99,0.917 3.302,1.115 0.313,0.198 10 false C68 1.552,0.844 1.781,1.031 0.229,0.188 10 false *1 2.167,0.833 2.396,1.021 0.229,0.188 10 false *2 2.76,0.854 2.99,1.042 0.229,0.188 10 false *3 3.344,0.833 3.573,1.021 0.229,0.188 10 false *4 4.01,0.125 6.323,0.521 2.313,0.396 10 false Front view of wire harness connector: (to No. 1 EDU) 4.99,0.958 5.302,1.156 0.313,0.198 10 false C74 3.948,2 4.323,2.177 0.375,0.177 10 false INJ7 4.323,2.125 4.698,2.302 0.375,0.177 10 false INJ6 4.688,2.135 5.063,2.313 0.375,0.177 10 false INJ4 5.073,2.146 5.448,2.323 0.375,0.177 10 false INJ1 5.438,2.125 5.896,2.313 0.458,0.188 10 false COM1 5.99,2.073 6.469,2.26 0.479,0.188 10 false COM2 0.125,1.5 1.573,1.677 1.448,0.177 10 false *1: No. 1 Fuel Injector 0.125,1.781 1.573,1.958 1.448,0.177 10 false *2: No. 4 Fuel Injector 0.115,2.094 1.563,2.271 1.448,0.177 10 false *3: No. 6 Fuel Injector 0.125,2.417 1.573,2.594 1.448,0.177 10 false *4: No. 7 Fuel Injector

a.

Disconnect the fuel injector connectors.


b.

Disconnect the No. 1 EDU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 1
Tester Connection Condition Specified Condition
C5-2 - C74-4 (INJ1) Always Below 1 Ω
C14-2 - C74-3 (INJ4) Always Below 1 Ω
C69-2 - C74-2 (INJ6) Always Below 1 Ω
C68-2 - C74-1 (INJ7) Always Below 1 Ω
C5-1 - C74-5 (COM1) Always Below 1 Ω
C14-1 - C74-5 (COM1) Always Below 1 Ω
C69-1 - C74-6 (COM2) Always Below 1 Ω
C68-1 - C74-6 (COM2) Always Below 1 Ω


Standard Resistance (Check for Short):
No. 1
Tester Connection Condition Specified Condition
C5-2 or C74-4 (INJ1) - Body ground Always 10 kΩ or higher
C14-2 or C74-3 (INJ4) - Body ground Always 10 kΩ or higher
C69-2 or C74-2 (INJ6) - Body ground Always 10 kΩ or higher
C68-2 or C74-1 (INJ7) - Body ground Always 10 kΩ or higher
C5-1 or C74-5 (COM1) - Body ground Always 10 kΩ or higher
C14-1 or C74-5 (COM1) - Body ground Always 10 kΩ or higher
C69-1 or C74-6 (COM2) - Body ground Always 10 kΩ or higher
C68-1 or C74-6 (COM2) - Body ground Always 10 kΩ or higher



A385207E02
1.146,0.875 1.521,1.104 0.375,0.229 1.75,0.885 2.125,1.115 0.375,0.229 2.344,0.885 2.719,1.115 0.375,0.229 2.927,0.885 3.302,1.115 0.375,0.229 4.917,0.917 5.333,1.156 0.417,0.24 4.281,2.052 4.552,1.802 true 4.542,2.094 4.677,1.802 true 4.802,2.104 4.844,1.823 true 5.177,2.115 5.021,1.802 true 5.49,2.104 5.177,1.802 true 5.948,2.104 5.333,1.802 true 0.802,0.115 3.115,0.51 2.313,0.396 10 false Front view of wire harness connector: (to Fuel injector) 1.198,0.906 1.51,1.104 0.313,0.198 10 false C70 1.823,0.917 2.135,1.115 0.313,0.198 10 false C67 2.438,0.917 2.75,1.115 0.313,0.198 10 false C9 2.99,0.917 3.302,1.115 0.313,0.198 10 false C54 1.552,0.844 1.781,1.031 0.229,0.188 10 false *1 2.167,0.833 2.396,1.021 0.229,0.188 10 false *2 2.76,0.854 2.99,1.042 0.229,0.188 10 false *3 3.344,0.833 3.573,1.021 0.229,0.188 10 false *4 4.01,0.115 6.323,0.51 2.313,0.396 10 false Front view of wire harness connector: (to No. 2 EDU) 4.99,0.958 5.302,1.156 0.313,0.198 10 false C76 3.948,2 4.323,2.177 0.375,0.177 10 false INJ3 4.323,2.125 4.698,2.302 0.375,0.177 10 false INJ8 4.688,2.135 5.063,2.313 0.375,0.177 10 false INJ5 5.073,2.146 5.448,2.323 0.375,0.177 10 false INJ2 5.438,2.125 5.917,2.313 0.479,0.188 10 false COM4 5.99,2.073 6.469,2.26 0.479,0.188 10 false COM5 0.125,1.5 1.573,1.677 1.448,0.177 10 false *1: No. 2 Fuel Injector 0.125,1.781 1.573,1.958 1.448,0.177 10 false *2: No. 3 Fuel Injector 0.115,2.094 1.563,2.271 1.448,0.177 10 false *3: No. 5 Fuel Injector 0.125,2.417 1.573,2.594 1.448,0.177 10 false *4: No. 8 Fuel Injector

d.

Disconnect the fuel injector connectors.


e.

Disconnect the No. 2 EDU connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 2
Tester Connection Condition Specified Condition
C70-2 - C76-4 (INJ2) Always Below 1 Ω
C9-2 - C76-3 (INJ5) Always Below 1 Ω
C67-2 - C76-1 (INJ3) Always Below 1 Ω
C54-2 - C76-2 (INJ8) Always Below 1 Ω
C70-1 - C76-5 (COM4) Always Below 1 Ω
C9-1 - C76-5 (COM4) Always Below 1 Ω
C67-1 - C76-6 (COM5) Always Below 1 Ω
C54-1 - C76-6 (COM5) Always Below 1 Ω


Standard Resistance (Check for Short):
No. 2
Tester Connection Condition Specified Condition
C70-2 or C76-4 (INJ2) - Body ground Always 10 kΩ or higher
C9-2 or C76-3 (INJ5) - Body ground Always 10 kΩ or higher
C67-2 or C76-1 (INJ3) - Body ground Always 10 kΩ or higher
C54-2 or C76-2 (INJ8) - Body ground Always 10 kΩ or higher
C70-1 or C76-5 (COM4) - Body ground Always 10 kΩ or higher
C9-1 or C76-5 (COM4) - Body ground Always 10 kΩ or higher
C67-1 or C76-6 (COM5) - Body ground Always 10 kΩ or higher
C54-1 or C76-6 (COM5) - Body ground Always 10 kΩ or higher




OK

10.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER FUEL CUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER FUEL CUT)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Cylinder #1, #2, #3, #4, #5, #6, #7 and #8 Fuel Cut.


d.

Check the engine idling condition while the fuel injection of each cylinder is cut using the tester.

Result
Engine Idling Condition Proceed to
Becomes unstable A
Does not change B

HINT:

Replace the fuel injector mounted on the cylinder that causes no significant idle speed change.




A

REPLACE INJECTOR DRIVER (No. 1 and/or No. 2)

B

REPLACE MALFUNCTIONING FUEL INJECTOR

11.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.


e.

Read the value.

Standard Value:
Item Inspection Condition Reference Value
Coolant Temp Idling with warm engine (A/C switch off) 75 to 90°C (167 to 194°F)




OK

12.READ VALUE USING INTELLIGENT TESTER (MAP)

NG

17.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
12.READ VALUE USING INTELLIGENT TESTER (MAP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Data List / MAP.


e.

Read the value.

OK:

Same value as the actual atmospheric pressure.




OK

13.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

NG

18.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
13.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.


d.

Read the value.

Standard Value:
Item Inspection Condition Reference Value
Engine Speed Idling with warm engine (A/C switch off)
·

500 to 600 rpm (M/T)

·

550 to 650 rpm (A/T)






OK

14.READ VALUE USING INTELLIGENT TESTER (ACCEL SENS. NO.# VOLT %)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR
14.READ VALUE USING INTELLIGENT TESTER (ACCEL SENS. NO.# VOLT %)
a.
C129061E02
0.576,1.599 1.330,1.807 0.754,0.208 10 Depressed 0.971,0.06 2.301,0.266 1.330,0.205 10 Accelerator Pedal 1.969,1.599 2.633,1.811 0.664,0.212 10 Released

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.


d.

Read the values.

Standard:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%




OK

15.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR)

NG

20.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
15.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Inlet Air.


d.

Read the value.

OK:

Same as air temperature near intake manifold.




OK

16.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

NG

21.INSPECT INTAKE AIR TEMPERATURE SENSOR
16.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


e.

Read the value.

Standard Value:
Item Inspection Condition Reference Value
Fuel Press Idling 27 to 37 MPa




OK

NG

22.INSPECT COMMON RAIL (for Bank 1) (FUEL PRESSURE SENSOR)
17.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.


OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

18.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.

A385083E01
1.833,0.958 2.281,1.229 0.448,0.271 4.073,0.875 4.521,1.146 0.448,0.271 4.917,0.865 5.365,1.135 0.448,0.271 3.5,2.25 3.917,1.833 true 4.344,2.427 4.052,1.979 true 4.885,2.26 4.552,1.833 true 0.667,0.135 3.198,0.51 2.531,0.375 10 false Front view of wire harness connector: (to Manifold Absolute Pressure Sensor) 3.583,0.135 5.948,0.51 2.365,0.375 10 false Front view of wire harness connector: (to ECM) 1.906,1.01 2.281,1.208 0.375,0.198 10 false C80 4.167,0.927 4.542,1.125 0.375,0.198 10 false C45 5.01,0.917 5.385,1.115 0.375,0.198 10 false C46 4.563,0.792 4.802,0.979 0.24,0.188 10 false *1 5.396,0.76 5.635,0.948 0.24,0.188 10 false *2 3.292,2.302 4.135,2.51 0.844,0.208 10 false 66 (VCPM) 4.094,2.458 4.938,2.667 0.844,0.208 10 false 114 (PIM) 4.74,2.271 5.333,2.469 0.594,0.198 10 false 75 (E2) 0.406,2 1.26,2.198 0.854,0.198 10 false *1: for LHD 0.396,2.354 1.25,2.552 0.854,0.198 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C80-2 (PIM) - C45-114 (PIM) Always Below 1 Ω
C80-3 (VC) - C45-66 (VCPM) Always Below 1 Ω
C80-1 (E) - C45-75 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C80-2 (PIM) - C46-114 (PIM) Always Below 1 Ω
C80-3 (VC) - C46-66 (VCPM) Always Below 1 Ω
C80-1 (E) - C46-75 (E2) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C80-2 (PIM) or C45-114 (PIM) - Body ground Always 10 kΩ or higher
C80-3 (VC) or C45-66 (VCPM) - Body ground Always 10 kΩ or higher
C80-1 (E) or C45-75 (E2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C80-2 (PIM) or C46-114 (PIM) - Body ground Always 10 kΩ or higher
C80-3 (VC) or C46-66 (VCPM) - Body ground Always 10 kΩ or higher
C80-1 (E) or C46-75 (E2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT CRANKSHAFT POSITION SENSOR
a.
A165740E01
0.107,0.226 2.586,0.589 2.479,0.363 10 Component without harness connected: (Crankshaft Position Sensor) 2.378,1.618 2.733,1.802 0.355,0.184 10 NE+ 0.765,1.618 1.036,1.802 0.272,0.184 10 NE- 1.461,2.105 1.152,1.744 false 1.977,2.139 2.292,1.744 false

Disconnect the crankshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NE+) - 2 (NE-) Cold 1630 to 2740 Ω
1 (NE+) - 2 (NE-) Hot 2065 to 3225 Ω


HINT:

In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

20.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.

A385267E01
1.74,0.938 2.156,1.198 0.417,0.26 4.583,0.802 5,1.063 0.417,0.26 5.292,0.792 5.708,1.052 0.417,0.26 1.198,1.969 1.656,1.75 true 1.156,1.458 1.76,1.698 true 1.469,1.208 1.885,1.688 true 2.01,1.708 2.375,1.208 true 2.125,1.698 2.635,1.448 true 2.24,1.729 2.698,1.844 true 4.365,1.115 5.01,1.906 true 4.792,2.24 5.094,1.906 true 4.938,2.375 5.156,1.906 true 5.448,2.448 5.229,1.917 true 5.802,1.344 5.313,1.917 true 5.646,2.25 5.375,1.906 true 0.729,0.135 3.115,0.51 2.385,0.375 10 false Front view of wire harness connector: (to Accelerator Pedal Position Sensor) 3.844,0.135 6.229,0.51 2.385,0.375 10 false Front view of wire harness connector: (to ECM) 1.823,0.99 2.167,1.188 0.344,0.198 10 false A31 0.75,1.917 1.188,2.115 0.438,0.198 10 false VCP2 0.719,1.354 1.156,1.552 0.438,0.198 10 false EPA2 1.042,1.021 1.479,1.219 0.438,0.198 10 false VPA2 2.396,1.021 2.833,1.219 0.438,0.198 10 false VCPA 2.677,1.344 3.115,1.542 0.438,0.198 10 false EPA 2.729,1.76 3.167,1.958 0.438,0.198 10 false VPA 3.75,0.927 4.427,1.125 0.677,0.198 10 false 53 (VPA) 4.094,2.167 4.823,2.365 0.729,0.198 10 false 54 (VPA2) 4.427,2.406 5.156,2.604 0.729,0.198 10 false 55 (VCPA) 5.219,2.479 5.948,2.677 0.729,0.198 10 false 56 (VCP2) 5.677,2.229 6.406,2.427 0.729,0.198 10 false 58 (EPA2) 5.833,1.229 6.563,1.427 0.729,0.198 10 false 57 (EPA) 4.667,0.854 5.01,1.052 0.344,0.198 10 false A38 5.375,0.844 5.719,1.042 0.344,0.198 10 false A52 5.031,0.719 5.271,0.917 0.24,0.198 10 false *1 5.729,0.698 5.969,0.896 0.24,0.198 10 false *2 0.198,2.406 1.219,2.615 1.021,0.208 10 false *1: for LHD 1.146,2.406 2.167,2.615 1.021,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
A31-1 (VCP2) - A38-56 (VCP2) Always Below 1 Ω
A31-2 (EPA2) - A38-58 (EPA2) Always Below 1 Ω
A31-3 (VPA2) - A38-54 (VPA2) Always Below 1 Ω
A31-4 (VCPA) - A38-55 (VCPA) Always Below 1 Ω
A31-5 (EPA) - A38-57 (EPA) Always Below 1 Ω
A31-6 (VPA) - A38-53 (VPA) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A31-1 (VCP2) - A52-56 (VCP2) Always Below 1 Ω
A31-2 (EPA2) - A52-58 (EPA2) Always Below 1 Ω
A31-3 (VPA2) - A52-54 (VPA2) Always Below 1 Ω
A31-4 (VCPA) - A52-55 (VCPA) Always Below 1 Ω
A31-5 (EPA) - A52-57 (EPA) Always Below 1 Ω
A31-6 (VPA) - A52-53 (VPA) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
A31-1 (VCP2) or A38-56 (VCP2) - Body ground Always 10 kΩ or higher
A31-2 (EPA2) or A38-58 (EPA2) - Body ground Always 10 kΩ or higher
A31-3 (VPA2) or A38-54 (VPA2) - Body ground Always 10 kΩ or higher
A31-4 (VCPA) or A38-55 (VCPA) - Body ground Always 10 kΩ or higher
A31-5 (EPA) or A38-57 (EPA) - Body ground Always 10 kΩ or higher
A31-6 (VPA) or A38-53 (VPA) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A31-1 (VCP2) or A52-56 (VCP2) - Body ground Always 10 kΩ or higher
A31-2 (EPA2) or A52-58 (EPA2) - Body ground Always 10 kΩ or higher
A31-3 (VPA2) or A52-54 (VPA2) - Body ground Always 10 kΩ or higher
A31-4 (VCPA) or A52-55 (VCPA) - Body ground Always 10 kΩ or higher
A31-5 (EPA) or A52-57 (EPA) - Body ground Always 10 kΩ or higher
A31-6 (VPA) or A52-53 (VPA) - Body ground Always 10 kΩ or higher




OK

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT INTAKE AIR TEMPERATURE SENSOR
a.

Remove the mass air flow meter (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER (w/o DPF)>REMOVAL).

A168114E01
1.498,3.291 1.959,3.477 0.461,0.185 10 5 (E2) 2.332,3.282 2.871,3.460 0.539,0.178 10 4 (THA) 2.235,2.808 2.452,3.248 false 1.839,3.268 2.112,2.809 false 4.163,0.477 4.390,0.652 0.228,0.174 10 30 4.163,0.654 4.374,0.831 0.211,0.177 10 20 4.163,0.925 4.378,1.112 0.215,0.187 10 10 4.234,1.211 4.376,1.388 0.142,0.177 10 5 4.234,1.422 4.364,1.584 0.129,0.162 10 3 4.234,1.602 4.365,1.762 0.130,0.161 10 2 4.234,1.873 4.381,2.036 0.147,0.163 10 1 4.163,2.155 4.407,2.325 0.244,0.170 10 0.5 4.163,2.35 4.412,2.513 0.250,0.163 10 0.3 4.163,2.512 4.447,2.678 0.284,0.166 10 0.2 4.163,2.756 4.402,2.919 0.239,0.163 10 0.1 4.453,3.172 4.769,3.355 0.316,0.184 10 -20 4.841,3.172 4.962,3.314 0.121,0.142 10 0 5.106,3.172 5.318,3.341 0.211,0.170 10 20 5.396,3.172 5.601,3.334 0.205,0.163 10 40 5.696,3.172 5.928,3.341 0.232,0.170 10 60 6.005,3.172 6.206,3.331 0.201,0.159 10 80 6.278,3.172 6.559,3.345 0.281,0.173 10 100 4.427,3.364 4.689,3.543 0.262,0.179 10 (-4) 4.728,3.364 5.022,3.543 0.295,0.179 10 (32) 5.036,3.364 5.331,3.543 0.295,0.179 10 (68) 5.309,3.364 5.696,3.543 0.387,0.179 10 (104) 5.641,3.364 6.029,3.543 0.387,0.179 10 (140) 5.981,3.364 6.368,3.543 0.387,0.179 10 (176) 6.345,3.364 6.733,3.543 0.387,0.179 10 (212) 6.077,1.459 6.844,1.622 0.767,0.163 10 Acceptable 6.047,1.537 5.353,1.815 false 2.978,1.087 3.974,1.275 0.996,0.187 10 Resistance kΩ 3.047,3.218 4.337,3.404 1.290,0.186 10 Temperature °C (°F) 0.608,0.018 3.096,0.383 2.488,0.365 10 Component without harness connected: (Mass Air Flow Meter)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (THA) - 5 (E2) -20°C (-4°F) 13.6 to 18.4 kΩ
20°C (68°F) 2.21 to 2.69 kΩ
60°C (140°F) 0.49 to 0.67 kΩ




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

22.INSPECT COMMON RAIL (for Bank 1) (FUEL PRESSURE SENSOR)
a.

Inspect the fuel pressure sensor (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>INSPECTION).



OK

23.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

REPLACE COMMON RAIL (for Bank 1)

23.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.

A385061E01
1.656,0.906 2.083,1.156 0.427,0.25 4.073,0.865 4.5,1.115 0.427,0.25 5.031,0.844 5.458,1.094 0.427,0.25 1.344,2.208 1.708,1.781 true 1.865,2.208 1.875,1.792 true 2.5,2.198 2.052,1.781 true 4.052,2.25 4.344,1.792 true 4.698,2.281 4.396,1.792 true 5.052,2.281 4.75,1.792 true 0.792,0.125 3.135,0.5 2.344,0.375 10 false Front view of wire harness connector: (to Fuel Pressure Sensor) 3.823,0.115 6.167,0.49 2.344,0.375 10 false Front view of wire harness connector: (to ECM) 1.74,0.948 2.115,1.146 0.375,0.198 10 false C82 4.167,0.906 4.542,1.104 0.375,0.198 10 false C45 4.552,0.781 4.927,0.979 0.375,0.198 10 false *1 5.115,0.885 5.49,1.083 0.375,0.198 10 false C46 5.521,0.771 5.896,0.969 0.375,0.198 10 false *2 1.771,2.24 2.146,2.438 0.375,0.198 10 false PR 1.177,2.24 1.552,2.438 0.375,0.198 10 false E2 2.531,2.219 2.906,2.417 0.375,0.198 10 false VG 3.552,2.271 4.396,2.479 0.844,0.208 10 false 69 (PCR1) 4.406,2.344 5.25,2.552 0.844,0.208 10 false 70 (VCM) 5.156,2.281 6,2.49 0.844,0.208 10 false 75 (E2) 0.115,2.042 0.958,2.25 0.844,0.208 10 false *1: for LHD 0.115,2.385 0.958,2.594 0.844,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C82-2 (PR) - C45-69 (PCR1) Always Below 1 Ω
C82-3 (VG) - C45-70 (VCM) Always Below 1 Ω
C82-1 (E2) - C45-75 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C82-2 (PR) - C46-69 (PCR1) Always Below 1 Ω
C82-3 (VG) - C46-70 (VCM) Always Below 1 Ω
C82-1 (E2) - C46-75 (E2) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C82-2 (PR) or C45-69 (PCR1) - Body ground Always 10 kΩ or higher
C82-3 (VG) or C45-70 (VCM) - Body ground Always 10 kΩ or higher
C82-1 (E2) or C45-75 (E2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C82-2 (PR) or C46-69 (PCR1) - Body ground Always 10 kΩ or higher
C82-3 (VG) or C46-70 (VCM) - Body ground Always 10 kΩ or higher
C82-1 (E2) or C46-75 (E2) - Body ground Always 10 kΩ or higher




OK

24.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.REPLACE ECM

b.

Check if the engine starts smoothly or if the engine stalls.

OK:

The engine starts smoothly and does not stall.




OK

END

NG