Home › Engine / Hybrid System › 1VD-FTV (COOLING) › WATER PUMP › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052795 1VD-FTV COOLING _0255198 WATER PUMP A

1VD-FTV COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 16100 1.INSTALL WATER PUMP ASSEMBLY

a.
U162988E02
2.771,2.083 3.156,2.354 0.385,0.271 10 true Nut 0.927,0.021 1.208,0.229 0.281,0.208 10 true Nut 0.542,1.542 0.698,1.708 0.156,0.167 10 false A 0.438,1.26 0.594,1.427 0.156,0.167 10 false B 0.5,2.385 0.656,2.552 0.156,0.167 10 false B 0.604,3.177 0.76,3.344 0.156,0.167 10 false B 2,3.177 2.156,3.344 0.156,0.167 10 false B 2.24,2.792 2.396,2.958 0.156,0.167 10 false B 0.698,2.01 0.854,2.177 0.156,0.167 10 false A 2.135,0.604 2.292,0.771 0.156,0.167 10 false A 2.771,1.313 2.927,1.479 0.156,0.167 10 false A

Temporarily install a new gasket and the water pump with the 9 bolts and 2 nuts.

Bolt Length
Item Length
Bolt A 30 mm (1.18 in.)
Bolt B 80 mm (3.15 in.)


b.
U162989E02
1.021,0.063 1.177,0.229 0.156,0.167 10 false 1 2.219,2.781 2.396,2.948 0.177,0.167 10 false 10 0.656,3.198 0.813,3.365 0.156,0.167 10 false 2 1.948,3.198 2.125,3.365 0.177,0.167 10 false 11 0.521,2.375 0.677,2.542 0.156,0.167 10 false 3 0.74,2.021 0.896,2.188 0.156,0.167 10 false 4 0.583,1.531 0.74,1.698 0.156,0.167 10 false 5 0.479,1.281 0.635,1.448 0.156,0.167 10 false 6 2.167,0.635 2.323,0.802 0.156,0.167 10 false 7 2.781,1.333 2.938,1.5 0.156,0.167 10 false 8 2.771,2.219 2.927,2.385 0.156,0.167 10 false 9

Uniformly tighten the 9 bolts and 2 nuts of the water pump in the order shown in the illustration.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)

NOTICE:

After installing all of the bolts and nuts, check that all of the bolts and nuts are tightened to the torque specification.



Hide 16331 2.INSTALL WATER OUTLET

a.
A161939

Connect the water outlet to the No. 2 water hose joint, and install a new gasket and the water outlet with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16307A 3.INSTALL FAN BRACKET SUB-ASSEMBLY

a.
U162987E02
0.854,0.083 1.01,0.25 0.156,0.167 10 false A 2.365,1.76 2.521,1.927 0.156,0.167 10 false B 0.635,1.583 0.792,1.75 0.156,0.167 10 false A 2.333,0.125 2.49,0.292 0.156,0.167 10 false A

Install the fan bracket with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Bolt Length
Item Length
Bolt A 30 mm (1.18 in.)
Bolt B 80 mm (3.15 in.)


Hide 15777 4.INSTALL NO. 1 OIL COOLER HOSE

NOTICE:

Make sure that there is clearance between the oil cooler hose and crankshaft pulley.


A174819

Hide 5.INSTALL NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)

a.
A180290

Temporarily install the No. 2 idler pulley bracket with the bolt.


b.

Temporarily install the 2 bolts to the No. 2 idler pulley bracket bolt hole.


c.
U163167E02
1.094,1.646 1.271,1.813 0.177,0.167 10 false 1 1.333,0.521 1.51,0.688 0.177,0.167 10 false 2 2.604,1.344 2.781,1.51 0.177,0.167 10 false 3

Uniformly tighten the 3 bolts of the No. 2 idler pulley bracket in the order shown in the illustration.

Torque:
49 N*m (495 kgf*cm, 36 ft.*lbf)


Hide 16630H 6.INSTALL NO. 2 IDLER PULLEY (w/ Viscous Heater)

a.
A177433

Install the collar, No. 2 idler pulley and cover with the bolt.

Torque:
49 N*m (495 kgf*cm, 36 ft.*lbf)


Hide 9.INSTALL NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)

Hide 87120G 10.INSTALL VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (w/ Viscous Heater)

Hide 87208 11.INSTALL HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 16371 12.INSTALL FAN PULLEY

Hide 32942 14.INSTALL OIL COOLER TUBE (for Automatic Transmission)

Hide 16.INSTALL NO. 3 IDLER PULLEY (w/ Viscous Heater)

Hide 17.INSTALL NO. 1 IDLER PULLEY (w/ Viscous Heater)

Hide 16572D 19.CONNECT NO. 2 RADIATOR HOSE

Hide 16571C 20.CONNECT NO. 1 RADIATOR HOSE

Hide 16470 22.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 44369A 23.INSTALL NO. 1 OIL RESERVOIR BRACKET

Hide 44360 24.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 17881 26.TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE

Hide 12601E 28.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

Hide 28800 30.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Connect the cables to negative (-) main battery and sub-battery terminals.


Hide 53292A 33.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 51405A 34.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53805 35.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 53806 36.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53736G 37.INSTALL FRONT FENDER APRON SEAL FRONT RH