Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The fuel sender gauge has a variable resistance mechanism. The resistance decreases when the fuel amount increases, and the resistance increases when the fuel amount decreases. The fuel receiver gauge changes based on the voltage of the fuel sender gauge.

WIRING DIAGRAM

E339204E03
0.271,5.906 2.344,6.146 2.073,0.24 10 false Fuel Sender Gauge Assembly 0.625,2.25 2.521,2.573 1.896,0.323 10 false Fuel Sender Gauge Assembly 0.25,3.156 3.49,3.438 3.24,0.281 10 false Fuel Suction with Pump and Gauge Tube Assembly 4.958,5.917 6.99,6.24 2.031,0.323 10 false Combination Meter Assembly 3.219,4.125 3.51,4.281 0.292,0.156 10 false FR2 4.99,4.917 5.198,5.063 0.208,0.146 10 false FE 0.156,6.354 2.052,6.677 1.896,0.323 10 false *1: for Double Tank 4.74,4.917 4.938,5.063 0.198,0.146 10 false 18 5,4.521 5.208,4.667 0.208,0.146 10 false L 4.74,4.521 4.938,4.667 0.198,0.146 10 false 36 4.99,4.125 5.198,4.271 0.208,0.146 10 false FR 4.74,4.135 4.938,4.281 0.198,0.146 10 false 34 4.969,5.76 5.354,5.958 0.385,0.198 10 false E119 3.583,4.115 3.813,4.271 0.229,0.156 10 false 1 3.219,4.521 3.51,4.677 0.292,0.156 10 false FV2 3.583,4.521 3.813,4.677 0.229,0.156 10 false 3 3.219,4.917 3.51,5.073 0.292,0.156 10 false FF2 3.594,4.927 3.823,5.083 0.229,0.156 10 false 2 3.281,0.99 3.573,1.146 0.292,0.156 10 false FV 4.979,1.823 5.385,1.969 0.406,0.146 10 false FE&B 4.74,1.813 4.938,1.958 0.198,0.146 10 false 17 4.979,1.406 5.188,1.552 0.208,0.146 10 false FR 4.74,1.396 4.938,1.542 0.198,0.146 10 false 33 4.979,1 5.188,1.146 0.208,0.146 10 false FV 4.74,1 4.938,1.146 0.198,0.146 10 false 35 3.573,0.99 3.802,1.146 0.229,0.156 10 false 1 3.281,1.396 3.573,1.552 0.292,0.156 10 false FR 3.573,1.406 3.802,1.563 0.229,0.156 10 false 3 3.271,1.802 3.563,1.958 0.292,0.156 10 false FE 3.573,1.813 3.802,1.969 0.229,0.156 10 false 2 0.26,2.979 0.49,3.135 0.229,0.156 10 false N1 0.271,5.74 0.604,5.948 0.333,0.208 10 false M3*1

PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1500 or B1501 is not output A
DTC B1500 is output B
DTC B1501 is output C



A

2.PERFORM ACTIVE TEST USING GTS (FUEL RECEIVER GAUGE ASSEMBLY)

B

C

2.PERFORM ACTIVE TEST USING GTS (FUEL RECEIVER GAUGE ASSEMBLY)
a.

Operate the GTS according to the steps on the display and select Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge EMPTY, 1/2 or FULL Perform the test with the vehicle stopped and engine idling.

OK:

Needle indication is normal.




OK

3.CHECK HARNESS AND CONNECTOR (FUEL RECEIVER CIRCUIT)

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL RECEIVER CIRCUIT)

*: for Double Tank


a.

Disconnect the E119 combination meter assembly connector.


b.

Disconnect the N1 fuel suction with pump and gauge tube assembly connector.


c.

Disconnect the M3 fuel sender gauge assembly connector.*


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-35 (FV) - N1-1 (FV) Always Below 1 Ω
E119-17 (FE&B) - N1-2 (FE) Always Below 1 Ω
E119-33 (FR) - N1-3 (FR) Always Below 1 Ω
E119-34 (FR) - M3-1 (FR2) Always Below 1 Ω
E119-36 (L) - M3-3 (FV2) Always Below 1 Ω
E119-18 (L) - M3-2 (FF2) Always Below 1 Ω
E119-35 (FV) or N1-1 (FV) - Body ground Always 10 kΩ or higher
E119-17 (FE&B) or N1-2 (FE) - Body ground Always 10 kΩ or higher
E119-33 (FR) or N1-3 (FR) Always 10 kΩ or higher
E119-34 (FR) or M3-1 (FR2) - Body Ground Always 10 kΩ or higher
E119-36 (L) or M3-3 (FV2) - Body Ground Always 10 kΩ or higher
E119-18 (L) or M3-2 (FF2) - Body Ground Always 10 kΩ or higher



Result
Result Proceed to
OK (for Double Tank) A
OK (except Double Tank) B
NG C


A

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

5.INSPECT FUEL SENDER GAUGE ASSEMBLY

C

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

A

5.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

C

D

E

5.INSPECT FUEL SENDER GAUGE ASSEMBLY


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1UR-FE) C
NG (for 3UR-FE) D
NG (for 1VD-FTV) E


A

6.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

B

C

D

E

6.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

b.
E322191E01
0.182,0.202 0.378,0.366 0.196,0.163 10 *a 0.182,1.714 0.378,1.877 0.196,0.163 10 *b 1.62,0.371 1.816,0.534 0.196,0.163 10 *c 1.62,1.775 1.816,1.939 0.196,0.163 10 *d

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-3 - B-1 Always Below 1 Ω
A-1 - B-3 Always Below 1 Ω
A-2 - B-1 Always 10 kΩ or higher
A-2 - B-3 Always 10 kΩ or higher
A-3 - B-3 Always 10 kΩ or higher


Text in Illustration
*a Upper Side
*b Lower Side
(to Fuel Sender Gauge Assembly)
*c Connector A
*d Connector B


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1UR-FE) C
NG (for 3UR-FE) D
NG (for 1VD-FTV) E


A

REPLACE COMBINATION METER ASSEMBLY

B

REPLACE FUEL SUCTION WITH PUMP ANDGAUGE TUBE ASSEMBLY

C

REPLACE FUEL SUCTION WITH PUMP ANDGAUGE TUBE ASSEMBLY

D

REPLACE FUEL SUCTION WITH PUMP ANDGAUGE TUBE ASSEMBLY

E

REPLACE FUEL SUCTION WITH PUMP ANDGAUGE TUBE ASSEMBLY