Home › Engine / Hybrid System › 3UR-FE (LUBRICATION) › OIL PUMP › 2015.08–2017.08
RM2660E _51 Engine / Hybrid System _052796 3UR-FE LUBRICATION _0255205 OIL PUMP A

3UR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 16322 1.INSTALL WATER INLET PIPE

a.

Apply soapy water to 2 new O-rings and install them to the inlet pipe.


b.

Install the inlet pipe to the No. 1 heat exchanger cover.


Hide 11302 2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new oil pump gasket.


b.

Install the oil pump gasket.


c.

Apply a light coat of engine oil to a new O-ring.


d.

Install the O-ring.


e.

Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

U163109E02
0.146,5.458 0.615,5.521 0.469,0.063 0.146,4.708 0.604,4.708 false 0.146,5.094 0.604,5.094 false 0.229,5.458 0.167,5.521 false 0.531,5.458 0.469,5.521 false 0.458,5.458 0.385,5.521 false 0.375,5.458 0.313,5.521 false 0.302,5.458 0.24,5.521 false 0.604,5.458 0.531,5.521 false 4.094,2.438 4.021,2.469 4.021,2.469 3.896,2.469 true 1.302,2.406 1.365,2.469 false 1.365,2.469 1.531,2.469 false 2.969,2.448 3.156,2.635 0.188,0.188 10 true E 2.125,2.385 2.26,2.552 0.135,0.167 10 true F 0.969,1.833 1.125,2.073 0.156,0.24 10 true E 4.771,5.167 5.104,5.354 0.333,0.188 10 false A - A 6.167,5.167 6.521,5.354 0.354,0.188 10 false B - B 3.927,4.167 4.469,4.344 0.542,0.177 10 false 7.0 mm 0.729,4.625 0.917,4.813 0.188,0.188 10 false *1 5.292,1.01 6.667,1.198 1.375,0.188 10 false A: 27.5 mm (1.08 in.) 5.292,1.302 6.667,1.51 1.375,0.208 10 false B: 32.5 mm (1.28 in.) 5.292,2.448 6.719,2.646 1.427,0.198 10 false F: 18.0 mm (0.709 in.) 5.292,2.167 6.74,2.365 1.448,0.198 10 false E: 16.0 mm (0.630 in.) 5.292,1.875 6.667,2.083 1.375,0.208 10 false D: 34.5 mm (1.36 in.) 5.292,1.583 6.646,1.792 1.354,0.208 10 false C: 35.0 mm (1.38 in.) 2.344,1.229 2.479,1.396 0.135,0.167 10 false A 0.698,2.813 0.833,2.979 0.135,0.167 10 false C 2.948,1.229 3.083,1.396 0.135,0.167 10 false B 4.531,2.854 4.667,3.021 0.135,0.167 10 false D 1.135,3.594 1.271,3.76 0.135,0.167 10 false E 4.01,3.594 4.146,3.76 0.135,0.167 10 false E 3.552,2.385 3.885,2.573 0.333,0.188 10 false A - A 1.563,2.396 1.917,2.583 0.354,0.188 10 false B - B 0.646,4.625 0.75,4.823 0.104,0.198 10 false : 0.646,5.021 0.75,5.219 0.104,0.198 10 false : 0.646,5.406 0.75,5.604 0.104,0.198 10 false : 5.49,4.167 6.031,4.344 0.542,0.177 10 false 7.0 mm 2.188,3.104 2.375,3.313 0.188,0.208 10 true E 0.729,5.021 0.917,5.208 0.188,0.188 10 false *2 0.729,5.417 0.917,5.604 0.188,0.188 10 false *3

Text in Illustration
*1 Continuous line area *2 Dashed line area
*3 Diagonal line area - -

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


A150825E15
1.646,1.208 2.385,0.896 2.385,0.896 2.677,0.896 true 0.656,0.302 0.969,0.5 0.313,0.198 10 false *1 0.198,0.604 0.938,0.792 0.74,0.188 10 false 6.0 (0.236) 0.198,1.104 0.938,1.292 0.74,0.188 10 false 4.0 (0.157) 0.198,1.292 0.938,1.479 0.74,0.188 10 false 3.2 (0.126) 0.208,1.625 0.948,1.813 0.74,0.188 10 false 2.0 (0.079) 2.74,0.844 3.052,1.042 0.313,0.198 10 false *5 2.656,1.573 2.969,1.771 0.313,0.198 10 false *2 1.073,1.75 1.354,1.938 0.281,0.188 10 false 8.0 1.573,1.75 1.885,1.906 0.313,0.156 10 false 10.0 2.146,1.75 2.458,1.906 0.313,0.156 10 false 12.0 0.958,1.906 1.438,2.073 0.479,0.167 10 false (0.315) 1.51,1.906 1.99,2.073 0.479,0.167 10 false (0.394) 2.063,1.906 2.542,2.073 0.479,0.167 10 false (0.472) 0.99,2.542 1.302,2.74 0.313,0.198 10 false *3 1.625,2.906 1.938,3.104 0.313,0.198 10 false *4

Apply Seal Packing as Follows:
Area Seal Packing Diameter Application Position from Inside Edge of Cover
Continuous Line Area 3.0 to 4.0 mm (0.118 to 0.157 in.) 2.5 mm (0.0984 in.)
Dashed Line Area 6.4 mm (0.252 in.) or more, or within OK area shown in illustration 7.0 mm (0.276 in.)
Diagonal Line Area 3.0 to 4.0 mm (0.118 to 0.157 in.) 5.5 mm (0.217 in.)


Text in Illustration
*1 Seal Packing Thickness mm (in.)
*2 Seal Packing Width mm (in.)
*3 Seal Packing Thickness
*4 Seal Packing Width
*5 OK Area


NOTICE:
·

When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

·

Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.




f.
A162541

Align the oil pump drive rotor spline and crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.


g.
U162880E02
2.813,0.813 2.958,0.99 0.146,0.177 10 false B 1.833,0.531 2,0.688 0.167,0.156 10 false *1 2.26,0.25 2.406,0.427 0.146,0.177 10 false A 1.781,2.063 1.969,2.271 0.188,0.208 10 true E 2.667,2.24 2.813,2.417 0.146,0.177 10 false F 2.948,1.938 3.094,2.115 0.146,0.177 10 false D 1.208,1.76 1.354,1.938 0.146,0.177 10 false C 2.542,2.781 2.688,2.958 0.146,0.177 10 false A 2.188,3.083 2.333,3.26 0.146,0.177 10 false A 1.771,3.135 1.917,3.313 0.146,0.177 10 false A 1.438,3.146 1.583,3.323 0.146,0.177 10 false A 1.021,3.073 1.167,3.25 0.146,0.177 10 false A 0.229,1.917 0.375,2.094 0.146,0.177 10 false A 0.167,1.052 0.313,1.229 0.146,0.177 10 false A 1.292,0.448 1.438,0.625 0.146,0.177 10 false A 1,0.292 1.146,0.469 0.146,0.177 10 false A 3.25,1.833 3.396,2.01 0.146,0.177 10 false A 3.156,1.052 3.302,1.229 0.146,0.177 10 false A 0.802,2.698 0.948,2.875 0.146,0.177 10 false B 0.74,2.417 0.885,2.594 0.146,0.177 10 false B 1.74,1.031 1.885,1.208 0.146,0.177 10 false B 2.594,2.479 2.74,2.656 0.146,0.177 10 false B 0.646,2.208 0.792,2.385 0.146,0.177 10 false D 2.24,1.51 2.385,1.688 0.146,0.177 10 false D 2.438,1.333 2.583,1.51 0.146,0.177 10 false D 0.927,1.344 1.115,1.542 0.188,0.198 10 true F 0.448,2.073 0.594,2.25 0.146,0.177 10 false F 1.406,0.667 1.552,0.844 0.146,0.177 10 false F 1.583,0.813 1.729,0.99 0.146,0.177 10 false F

Temporarily install the timing chain cover with the 28 bolts and nut.

Standard Bolt:
Item Length Thread Diameter
Bolt A 25 mm (0.984 in.) 8 mm (0.315 in.)
Bolt B 55 mm (2.17 in.) 8 mm (0.315 in.)
Bolt C 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt D 35 mm (1.38 in.) 10 mm (0.394 in.)
Bolt E 55 mm (2.17 in.) 10 mm (0.394 in.)
Bolt F 80 mm (3.15 in.) 10 mm (0.394 in.)


Text in Illustration
*1 Nut

NOTICE:

Make sure that there is no oil on the bolt threads.



h.
A174145E06
2.24,0.979 2.427,1.198 0.188,0.219 10 true 1 0.865,1.656 1.01,1.823 0.146,0.167 10 false 2 0.594,1.396 0.74,1.563 0.146,0.167 10 false 3

Tighten the 3 bolts in several steps in the sequence shown in the illustration.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


i.
A163330E07
2.375,1.99 2.5,2.156 0.125,0.167 10 false A 3.26,1.635 3.385,1.802 0.125,0.167 10 false B 0.521,0.146 0.677,0.344 0.156,0.198 10 true A 0.281,1.625 0.406,1.792 0.125,0.167 10 true A

Temporarily install the fluid coupling bracket with the 4 bolts.

Standard Bolt:
Item Length Thread Diameter
Bolt A 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt B 80 mm (3.15 in.) 10 mm (0.394 in.)



j.
A162527

Temporarily install the belt tensioner with the standard bolt and 6 mm hexagon wrench bolt.


k.
A174146E01
1.619,0.1 1.740,0.272 0.121,0.172 10 4 1.844,0.098 1.965,0.270 0.121,0.172 10 5 2.865,1.367 2.987,1.539 0.121,0.172 10 6 3.098,1.056 3.219,1.228 0.121,0.172 10 7 2.109,0 2.230,0.172 0.121,0.172 10 8 1.34,0 1.461,0.172 0.121,0.172 10 9 0.194,1.122 0.381,1.294 0.187,0.172 10 10 2.552,1.666 2.739,1.837 0.187,0.172 10 11

Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


l.
A162544E07
0.583,1.885 0.802,2.094 0.219,0.208 10 true 12 1.74,0.802 1.938,0.979 0.198,0.177 10 false 13 2.521,2.792 2.719,2.969 0.198,0.177 10 false 19 2.594,2.521 2.792,2.698 0.198,0.177 10 false 18 2.479,2.208 2.677,2.385 0.198,0.177 10 false 17 1.479,2.104 1.677,2.281 0.198,0.177 10 true 16 1.406,1.042 1.604,1.219 0.198,0.177 10 false 15 2.01,1.823 2.219,1.979 0.208,0.156 10 true 14 0.615,2.188 0.813,2.365 0.198,0.177 10 false 20 0.177,1.052 0.375,1.229 0.198,0.177 10 false 28 0.25,1.958 0.448,2.135 0.198,0.177 10 false 27 2.135,3.125 2.333,3.302 0.198,0.177 10 false 26 1.729,3.156 1.927,3.333 0.198,0.177 10 false 25 0.719,2.729 0.917,2.906 0.198,0.177 10 false 22 0.969,3.104 1.167,3.281 0.198,0.177 10 false 24 1.396,3.146 1.594,3.323 0.198,0.177 10 false 23 0.688,2.438 0.885,2.615 0.198,0.177 10 false 21 0.958,0.323 1.156,0.5 0.198,0.177 10 false 30 1.24,0.479 1.438,0.656 0.198,0.177 10 false 29 2.896,2.01 3.094,2.188 0.198,0.177 10 false 34 2.219,0.281 2.417,0.458 0.198,0.177 10 false 33 1.917,0.531 2.115,0.708 0.198,0.177 10 false 32 2.531,1.625 2.729,1.802 0.198,0.177 10 true 31 3.052,1.063 3.25,1.24 0.198,0.177 10 false 35

Tighten the 23 bolts and nut labeled 12 to 35 in several steps in the sequence shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after installing.

·
A162545E05
1.292,0.427 0.927,1.688 true 0.927,1.677 2.167,0.417 true 0.844,1.698 0.979,1.885 0.135,0.188 10 false A

After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.




Hide 11202 4.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.

Install 5 new gaskets to the camshaft bearing caps (No. 2, No. 3).


b.

Install a new gasket to the cylinder head cover.

NOTICE:

Remove any oil from the contact surface.



c.
A385337

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.
A162523E07
1.979,1.115 2.167,0.854 2.167,0.854 2.26,0.854 true 2.281,0.771 2.417,0.938 0.135,0.167 10 true A 1.281,0.104 1.417,0.271 0.135,0.167 10 true 1 1.677,1.906 1.813,2.073 0.135,0.167 10 true 2 1.833,0.104 1.969,0.271 0.135,0.167 10 true 3 1.135,1.885 1.271,2.052 0.135,0.167 10 true 4 0.844,0.021 0.979,0.188 0.135,0.167 10 true 5 2.531,0.115 2.667,0.281 0.135,0.167 10 true 7 0.042,1.833 0.177,2 0.135,0.167 10 false 8 0.042,0.146 0.177,0.313 0.135,0.167 10 false 9 2.667,1.906 2.854,2.073 0.188,0.167 10 true 11 3.219,0.135 3.406,0.302 0.188,0.167 10 true 12 3.229,1.5 3.417,1.667 0.188,0.167 10 true 13 1.875,1.5 2.063,1.667 0.188,0.167 10 true 14 0.01,1.313 0.198,1.479 0.188,0.167 10 true 10 2.177,1.917 2.323,2.094 0.146,0.177 10 true 6

Install the cylinder head cover and a new seal washer with the 14 bolts in the order shown in the illustration.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 11201 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.

Install 5 new gaskets to the camshaft bearing caps. (No. 1, No. 3).


b.

Install a new gasket to the cylinder head cover.

NOTICE:

Remove any oil from the contact surface.



c.
A385338

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.
A162525E07
1.49,1.115 1.677,0.854 1.677,0.854 1.771,0.854 true 1.792,0.771 1.927,0.938 0.135,0.167 10 true A 2.063,0.115 2.198,0.281 0.135,0.167 10 true 1 1.698,1.906 1.833,2.073 0.135,0.167 10 true 2 1.406,0.104 1.542,0.271 0.135,0.167 10 true 3 2.198,1.896 2.333,2.063 0.135,0.167 10 true 4 2.521,0.01 2.656,0.177 0.135,0.167 10 true 5 0.854,0.115 0.99,0.281 0.135,0.167 10 true 7 1.156,1.906 1.292,2.073 0.135,0.167 10 true 6 3.302,1.844 3.406,2.01 0.104,0.167 10 false 8 3.302,0.104 3.406,0.271 0.104,0.167 10 false 9 0.594,1.906 0.781,2.073 0.188,0.167 10 true 11 0.031,0.146 0.219,0.313 0.188,0.167 10 false 12 0.021,1.51 0.208,1.677 0.188,0.167 10 true 13 1.375,1.49 1.563,1.656 0.188,0.167 10 true 14 3.229,1.313 3.417,1.479 0.188,0.167 10 true 10

Install the cylinder head cover and a new seal washer with the 14 bolts in the order shown in the illustration.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after the installation.



e.

Install the noise filter to the cylinder head cover with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 19500 6.INSTALL IGNITION COIL ASSEMBLY

a.

Install the 8 ignition coils with the 8 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13521A 7.INSTALL CRANKSHAFT TIMING GEAR KEY

a.

Install the crankshaft timing gear key to the crankshaft.


Hide 8.CONNECT WIRE HARNESS CLAMP BRACKET

a.

Connect the bracket to the timing chain cover with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 13471 9.INSTALL CRANKSHAFT PULLEY

a.
A164230E08
1.667,1.521 1.667,1.75 1.667,1.75 2.031,1.75 true 2.031,1.333 2.031,1.875 true 0.24,0.563 0.417,0.76 0.177,0.198 10 false *a 1.854,1.875 2.188,2.063 0.333,0.188 10 false SST

Align the pulley set key with the key groove of the pulley, and slide on the pulley.


b.

Using SST, install the pulley set bolt.

SST
09213-70011  
09330-00021  

Torque:
300 N*m (3059 kgf*cm, 221 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn


Hide 16603 10.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.

Install the idler pulley with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16173 11.INSTALL WATER PUMP PULLEY

a.
A162556E05
0.604,1.521 0.604,1.458 false 0.604,1.458 1.052,1.219 false 0.479,1.573 0.813,1.76 0.333,0.188 10 false SST

Temporarily install the pulley with the 4 bolts.


b.

Using SST, hold the pulley and tighten the 4 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16323 12.INSTALL WATER INLET HOUSING

a.
A162555E08
0.51,0.375 0.802,0.375 0.802,0.375 1.229,0.74 true 0.333,0.281 0.51,0.458 0.177,0.177 10 false *1

Install a new gasket to the timing chain cover.


b.

Install the water inlet with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Text in Illustration
*1 Gasket


Hide 12611 13.INSTALL NO. 1 ENGINE COVER

Hide 11212 14.INSTALL NO. 2 ENGINE COVER

Hide 16355 15.INSTALL FRONT WATER BY-PASS JOINT

a.

Install 2 new gaskets and the water by-pass joint with the 4 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the No. 2 water by-pass hose to the water by-pass joint.


Hide 16206 16.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the 2 hoses.


b.

Install the water by-pass pipe with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16261G 17.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Install the No. 1 water by-pass hose by connecting the hose to the water inlet housing and front water by-pass joint.


Hide 44310 20.CONNECT VANE PUMP ASSEMBLY

A163333E15
1.792,1.917 1.552,1.917 1.552,1.917 0.906,1.573 true 1.823,1.833 2.031,2.021 0.208,0.188 10 true *1

HINT:

Before performing the following procedures, move the spacer until the vane pump can be installed.

Text in Illustration
*1 Spacer


a.

Connect the vane pump to the timing chain cover with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16207 24.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the 4 hoses.


b.

Install the water by-pass pipe with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 83520 25.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 23902 28.CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A165142E11
0.052,0.083 0.323,0.323 0.271,0.24 10 false *A 0.063,2.271 0.427,2.479 0.365,0.208 10 false *B

Connect the fuel tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*A LH Side
*B RH Side


Hide 88320 29.CONNECT COOLER COMPRESSOR ASSEMBLY

a.
A178491E01
3.048,1.511 3.192,1.679 0.144,0.169 10 1 3.129,1.829 3.294,1.998 0.165,0.169 10 2 3.295,1.305 3.405,1.474 0.110,0.169 10 3 2.618,1.842 2.783,2.011 0.165,0.169 10 4

Install the cooler compressor with the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the 3 bolts and nut.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)

NOTICE:

Tighten the bolts and nut in the order shown in the illustration to install the cooler compressor.



Hide 30.CONNECT WATER PIPE AND HOSE SUB-ASSEMBLY

a.

Connect the water pipe and hose to the cylinder head cover with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the 3 hoses.


Hide 31.CONNECT ENGINE WIRE

a.

Connect the 2 clamps and power steering oil pressure switch connector.


b.

Engine Room RH Side:

i.

Connect the 6 clamps.


ii.

Connect the throttle position sensor and throttle control motor connector.


iii.

Connect the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iv.

Connect the noise filter connector.


v.

Connect the 2 VVT sensor connectors.


vi.

Connect the injector connector.


vii.

Connect the 4 ignition coil connectors.


viii.

Connect the 2 camshaft timing oil control valve connectors.



c.

Engine Room LH Side:

i.

Connect the cooler compressor connector.


ii.

Connect the 3 clamps.


iii.

Connect the camshaft position sensor connector.


iv.

Connect the 2 camshaft timing oil control valve connectors.


v.

Connect the engine coolant temperature sensor connector.


vi.

Connect the 4 clamps.


vii.

Connect the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


viii.

Connect the noise filter connector.


ix.

Connect the 2 VVT sensor connectors.


x.

Connect the 4 ignition coil connectors.


xi.

Connect the injector connector.


xii.

Connect the 2 connectors and 2 clips to the engine room junction block.


xiii.

Install the engine room relay block cover.



Hide 16400 32.INSTALL RADIATOR ASSEMBLY

Hide 38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 51405C 43.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53736G 44.INSTALL FRONT FENDER APRON SEAL FRONT RH

Hide 55781E 46.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53294C 47.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 32917 48.INSTALL TRANSMISSION OIL COOLER AIR DUCT