Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.06
RM2660E _51 Engine / Hybrid System _052778 1GR-FE ENGINE MECHANICAL _0255061 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

a.
A225385E05
1.031,4.406 0.927,4.406 0.927,4.406 0.708,4.177 false 0.938,4.104 1.385,4.104 false 1.115,3.875 0.708,3.875 false 0.99,2.344 1.167,2.344 false 1.063,2.135 0.75,2.135 false 1.052,2.938 0.938,2.938 0.938,2.938 0.75,3.104 false 2.625,2.229 2.542,2.229 2.542,2.229 2.354,2.656 false 2.594,2.802 2.729,2.802 false 2.635,3.479 2.563,3.479 2.563,3.479 2.365,3.083 false 0.25,0.948 0.385,1.135 0.135,0.188 10 false A 0.229,0.469 0.375,0.646 0.146,0.177 10 false A 0.146,3.281 0.594,3.469 0.448,0.188 10 false A (M8) 1.854,3.25 2.333,3.427 0.479,0.177 10 false B (M6) 2.021,1.448 2.208,1.656 0.188,0.208 10 true B 3,1.021 3.198,1.24 0.198,0.219 10 true B 1.896,0.875 2.094,1.052 0.198,0.177 10 true C 3.167,1.521 3.292,1.688 0.125,0.167 10 false C 0.125,4.375 0.604,4.573 0.479,0.198 10 false C (M6) 1.073,4.333 2.135,4.531 1.063,0.198 10 false 9 mm (0.354 in.) 1.406,4.021 2.552,4.229 1.146,0.208 10 false 19 mm (0.748 in.) 1.156,3.792 2.229,3.99 1.073,0.198 10 false 9 mm (0.354 in.) 1.094,2.042 2.24,2.25 1.146,0.208 10 false 20 mm (0.787 in.) 1.052,2.875 1.75,3.229 0.698,0.354 10 false 13 mm (0.512 in.) 1.208,2.26 1.802,2.615 0.594,0.354 10 false 73 mm (2.87 in.) 2.667,3.396 3.313,3.74 0.646,0.344 10 false 9 mm (0.354 in.) 2.656,2.146 3.302,2.521 0.646,0.375 10 false 16 mm (0.630 in.) 2.75,2.719 3.323,3.104 0.573,0.385 10 false 27 mm (1.06 in.)

Install the oil pan stud bolt.

i.

Using E6 and E8 "TORX" socket wrenches, install the 6 stud bolts as shown in the illustration.

Torque:
for stud bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for stud bolt B and C : 4.0 N*m (41 kgf*cm, 35 in.*lbf)



b.
A225387E04
2.479,1.49 2.479,1.281 2.479,1.281 2.333,1.208 false 2.719,0.792 2.573,0.792 false 2.615,0.177 2.531,0.177 2.531,0.177 2.333,0.76 false 1.875,1.281 2.115,1.479 0.24,0.198 10 false M6 2.292,1.531 2.969,1.927 0.677,0.396 10 false 9 mm (0.354 in.) 2.646,0.094 3.292,0.49 0.646,0.396 10 false 21 mm (0.827 in.) 2.729,0.74 3.302,1.104 0.573,0.365 10 false 34 mm (1.34 in.)

Install the cylinder head cover LH stud bolt.

i.

Using an E6 "TORX" socket wrench, install the stud bolt as shown in the illustration.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)



Hide 2.INSTALL RING PIN

a.

Using a plastic-faced hammer, tap in new ring pins to the camshaft housing.

Standard protrusion height:

2.7 to 3.3 mm (0.106 to 0.130 in.)


A225382E06
0.185,0.013 0.439,0.208 0.254,0.195 10 *a 2.837,0.013 3.091,0.208 0.254,0.195 10 *b 6.369,1.171 6.623,1.366 0.254,0.195 10 *1

Text in Illustration
*1 Protrusion Height - -
*a LH *b RH


Hide 3.INSTALL STRAIGHT PIN

a.

Using a plastic-faced hammer, tap in new straight pins to the camshaft housing.

Standard Protrusion Height:
Item Specified Condition
Straight pin A 7.7 to 8.3 mm (0.303 to 0.327 in.)
Straight pin B 5.7 to 6.3 mm (0.224 to 0.248 in.)


A225383E06
0.268,0.022 0.470,0.215 0.202,0.193 10 *a 2.89,0.022 3.092,0.215 0.202,0.193 10 *b 1.118,0.589 1.280,0.784 0.162,0.195 10 A 4.103,0.645 4.264,0.840 0.162,0.195 10 A 2.859,0.586 3.021,0.781 0.162,0.195 10 B 2.428,0.667 2.590,0.862 0.162,0.195 10 B 4.655,2.501 4.817,2.696 0.162,0.195 10 B 0.524,2.617 0.655,2.782 0.132,0.165 10 B 5.718,0.336 5.879,0.531 0.162,0.195 10 A 5.716,1.619 5.877,1.814 0.162,0.195 10 B 6.201,0.617 6.403,0.810 0.202,0.193 10 *1 6.215,1.859 6.417,2.052 0.202,0.193 10 *1

Text in Illustration
*1 Protrusion Height - -
*a LH *b RH


Hide 11381A 4.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A076268E06
1.75,1.458 2.25,1.542 false 2.333,1.448 2.698,1.677 0.365,0.229 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear oil seal retainer edge.

SST
09223-78010  


b.

Apply MP grease to the lip of the oil seal.


Hide 11381 5.INSTALL ENGINE REAR OIL SEAL RETAINER

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the oil seal retainer or cylinder block.


b.
A076269E09
1.896,0.448 2.125,0.135 2.125,0.135 2.313,0.135 false 2.375,0.063 2.656,0.25 0.281,0.188 10 false *1

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2 to 3 mm (0.0787 to 0.118 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the oil seal retainer within 3 minutes after applying seal packing.




c.

Install the oil seal retainer with the 5 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.

·

Do not start the engine for at least 2 hours after installation.




Hide 6.INSTALL CYLINDER BLOCK WATER JACKET SPACER

A225710E03
0.396,1.896 0.396,1.708 0.396,1.708 0.635,1.438 false 2.625,1.281 2.958,1.281 false 2.094,0.875 2.208,0.875 2.208,0.875 2.396,1.156 false 1.365,1 1.25,1 1.25,1 0.833,1.344 false 3,1.219 3.188,1.385 0.188,0.167 10 false *1 0.292,1.927 0.479,2.094 0.188,0.167 10 false *1 1.854,0.792 2.052,0.958 0.198,0.167 10 false *2 1.406,0.938 1.594,1.104 0.188,0.167 10 false *3

a.

Install the 2 water jacket spacers as shown in the illustration.

Text in Illustration
*1 UP Mark
*2 L Mark
*3 R Mark

NOTICE:

Make sure that the "L mark", "R mark" and "UP mark" are oriented as shown in the illustration.



Hide 13716 13.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem caps.


b.

Install the 24 valve stem caps to the cylinder head.


Hide 13750 14.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

b.

Install the 24 valve lash adjusters to the cylinder head.

NOTICE:

Install the lash adjuster at the same place it was removed from.



Hide 13801 15.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply engine oil to the lash adjuster tips and valve stem cap ends.


b.
A221097E01
2.085,0.102 2.248,0.272 0.163,0.170 10 *1 0.426,0.941 0.597,1.110 0.171,0.170 10 *2 0.965,1.78 1.128,1.950 0.163,0.170 10 *3 2.674,0.701 2.837,0.870 0.163,0.170 10 *4 2.054,0.186 1.859,0.186 1.859,0.186 1.706,0.42 false 1.116,1.028 0.633,1.028 false 1.165,1.865 1.428,1.865 1.428,1.865 2.076,0.844 false 2.182,0.793 2.644,0.793 false

Install the 24 valve rocker arms as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Lash Adjuster
*3 Valve Stem
*4 Valve Stem Cap


Hide 16.INSTALL CAMSHAFT BEARING CAP (for Bank 2)

a.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


b.

Install the No. 3 camshaft and No. 4 camshaft to the camshaft housing.


c.
A221187

Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.


d.
A221188E04
1.438,0.063 1.552,0.208 0.115,0.146 10 false 1 2.104,0.063 2.219,0.208 0.115,0.146 10 false 3 2.771,0.052 2.885,0.198 0.115,0.146 10 false 7 2.104,1.552 2.281,1.75 0.177,0.198 10 true 4 1.448,1.552 1.615,1.708 0.167,0.156 10 true 2 0.604,1.531 0.771,1.688 0.167,0.156 10 true 6 0.615,0.031 0.792,0.188 0.177,0.156 10 true 5 2.76,1.542 2.927,1.698 0.167,0.156 10 true 8

Temporarily install the 8 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11104A 17.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A221097E01
2.085,0.102 2.248,0.272 0.163,0.170 10 *1 0.426,0.941 0.597,1.110 0.171,0.170 10 *2 0.965,1.78 1.128,1.950 0.163,0.170 10 *3 2.674,0.701 2.837,0.870 0.163,0.170 10 *4 2.054,0.186 1.859,0.186 1.859,0.186 1.706,0.42 false 1.116,1.028 0.633,1.028 false 1.165,1.865 1.428,1.865 1.428,1.865 2.076,0.844 false 2.182,0.793 2.644,0.793 false

Make sure that the valve rocker arm is installed as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Lash Adjuster
*3 Valve Stem
*4 Valve Stem Cap


b.
A221189E01
3.227,0.364 3.399,0.564 0.172,0.200 10 *1 3.209,0.458 3.012,0.458 false

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A223640E04
1.271,2.51 1.833,3.031 1.833,3.031 2.417,2.49 false 0.219,1.667 0.448,1.854 0.229,0.188 10 true 8 0.198,1.094 0.375,1.313 0.177,0.219 10 true 7 0.354,0.51 0.521,0.781 0.167,0.271 10 true 9 1.729,0.583 1.917,0.781 0.188,0.198 10 true 6 1.75,1.135 1.917,1.323 0.167,0.188 10 true 4 1.771,1.698 1.958,1.885 0.188,0.188 10 true 5 1.042,1.677 1.24,1.865 0.198,0.188 10 true 2 1.063,1.115 1.25,1.292 0.188,0.177 10 true 1 1.063,0.552 1.26,0.729 0.198,0.177 10 true 3 3.208,0.615 3.417,0.823 0.208,0.208 10 true 12 2.333,1.667 2.573,1.896 0.24,0.229 10 true 11 3.156,1.344 3.396,1.594 0.24,0.25 10 true 13 1.729,2.125 1.917,2.333 0.188,0.208 10 false *a 1.708,3.052 1.906,3.24 0.198,0.188 10 false *1 1.167,2.021 1.5,2.208 0.333,0.188 10 false 15° 2.302,1.167 2.542,1.396 0.24,0.229 10 true 10

Install the camshaft housing sub-assembly LH and tighten the 13 bolts in the order shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Text in Illustration
*1 Knock Pin
*a Front View

NOTICE:
·

When installing the camshaft housing sub-assembly LH, it is necessary to correctly position the camshafts as shown in the illustration. Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.

·

If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly LH, clean the installation surfaces and reapply seal packing.

·

If the camshaft housing sub-assembly LH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

·

Do not start the engine for at least 2 hours after installing.




d.
A221184E08
0.271,0.75 0.479,0.958 0.208,0.208 10 true 1 1.073,0.771 1.26,0.969 0.188,0.198 10 true 2 1.75,0.771 1.958,0.969 0.208,0.198 10 true 3 2.417,0.781 2.615,0.979 0.198,0.198 10 true 4 0.25,1.385 0.438,1.625 0.188,0.24 10 true 5 1.073,1.417 1.26,1.635 0.188,0.219 10 true 6 1.74,1.417 1.969,1.604 0.229,0.188 10 true 7 2.396,1.406 2.604,1.615 0.208,0.208 10 true 8

Tighten the 8 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 18.INSTALL CAMSHAFT BEARING CAP (for Bank 1)

a.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


b.

Install the camshaft and No. 2 camshaft to the camshaft housing.


c.
A221190

Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.


d.
A221387E04
0.708,0.115 0.833,0.271 0.125,0.156 10 false 7 1.396,0.115 1.521,0.271 0.125,0.156 10 false 3 2.083,0.104 2.208,0.26 0.125,0.156 10 false 1 2.698,0.073 2.927,0.24 0.229,0.167 10 true 5 2.729,1.635 2.938,1.823 0.208,0.188 10 true 6 2.104,1.646 2.302,1.833 0.198,0.188 10 true 2 1.385,1.646 1.573,1.854 0.188,0.208 10 true 4 0.708,1.625 0.875,1.854 0.167,0.229 10 true 8

Temporarily install the 8 bearing cap bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11103C 19.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

a.
A221097E03
2.085,0.102 2.248,0.272 0.163,0.170 10 *1 0.426,0.941 0.597,1.110 0.171,0.170 10 *2 0.965,1.78 1.128,1.950 0.163,0.170 10 *3 2.674,0.701 2.837,0.870 0.163,0.170 10 *4 2.054,0.186 1.859,0.186 1.859,0.186 1.706,0.42 false 1.116,1.028 0.633,1.028 false 1.165,1.865 1.428,1.865 1.428,1.865 2.076,0.844 false 2.182,0.793 2.644,0.793 false

Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Lash Adjuster
*3 Valve Stem
*4 Valve Stem Cap


b.
A221388E01
0.059,0.397 0.228,0.570 0.169,0.173 10 *1 0.238,0.483 0.607,0.483 false

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A223641E04
1.042,2.49 1.552,3.073 1.552,3.073 2.438,2.531 false 1.01,1.125 1.198,1.313 0.188,0.188 10 true 8 1.01,0.552 1.229,0.75 0.219,0.198 10 true 7 0.875,0 1.073,0.219 0.198,0.219 10 true 9 1.74,0.052 1.938,0.229 0.198,0.177 10 true 6 1.708,0.542 1.906,0.771 0.198,0.229 10 true 4 1.698,1.135 1.896,1.313 0.198,0.177 10 true 5 2.406,1.115 2.615,1.292 0.208,0.177 10 true 2 2.406,0.531 2.573,0.719 0.167,0.188 10 true 1 2.427,0 2.646,0.25 0.219,0.25 10 true 3 3.083,0 3.365,0.26 0.281,0.26 10 true 12 3.063,0.469 3.292,0.677 0.229,0.208 10 true 10 3.021,1.271 3.25,1.479 0.229,0.208 10 true 11 1.604,2.135 1.802,2.313 0.198,0.177 10 false *a 1.427,3.094 1.604,3.281 0.177,0.188 10 false *1 2.917,2.333 3.167,2.49 0.25,0.156 10 false 45°

Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the order shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Text in Illustration
*1 Knock Pin
*a Front View

NOTICE:
·

When installing the camshaft housing RH, it is necessary to correctly position the camshafts as shown in the illustration.

Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.

·

If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly RH, clean the installation surfaces and reapply seal packing.

·

If the camshaft housing sub-assembly RH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

·

Do not start the engine for at least 2 hours after installing.




d.
A221179E08
0.708,0.792 0.917,0.969 0.208,0.177 10 true 8 1.406,0.792 1.604,0.958 0.198,0.167 10 true 7 2.104,0.781 2.313,0.948 0.208,0.167 10 true 6 2.719,0.771 2.896,0.938 0.177,0.167 10 true 5 0.688,0.125 0.896,0.281 0.208,0.156 10 true 4 1.406,0.125 1.594,0.302 0.188,0.177 10 true 3 2.104,0.115 2.302,0.271 0.198,0.156 10 true 2 2.719,0.073 2.938,0.25 0.219,0.177 10 true 1

Tighten the 8 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 13560A 20.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY (for Bank 2)

a.
A222171E04
1.198,2.688 1.313,2.688 1.313,2.688 1.479,2.438 false 1.125,2.302 1.219,2.042 1.219,2.042 1.396,2.042 false 1.417,1.927 1.594,2.115 0.177,0.188 10 false *1 1,2.604 1.177,2.792 0.177,0.188 10 false *2 1.135,0.563 1.385,0.76 0.25,0.198 10 true *a

Install the No. 3 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Push in the tensioner and insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the tensioner.

Text in Illustration
*1 Pin
*2 Plunger
*a Push


Hide 21.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

a.
A227957E01
1.48,0.065 1.668,0.230 0.188,0.165 10 *1 1.52,1.692 1.718,1.862 0.198,0.170 10 *2 2.558,1.178 2.184,0.143 2.184,0.143 1.702,0.143 false 0.834,1.015 1.632,1.667 1.632,1.667 2.372,1.071 false 0.808,0.509 1.182,0.145 1.182,0.145 1.424,0.145 false

Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.

Text in Illustration
*1 Timing Mark
*2 Mark Plate


b.

Apply a light coat of engine oil to the bolt threads and bolt-seating surface.


c.

Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear LH with the No. 2 chain sub-assembly installed.


d.
A223637E01
2.722,0.19 3.100,0.402 0.378,0.211 10 SST 0.307,0 0.509,0.221 0.202,0.221 10 *a 2.962,1.134 3.164,1.355 0.202,0.221 10 *b 2.682,0.272 2.484,0.272 2.484,0.272 1.613,0.756 false

Using SST to hold the hexagonal portion of each camshaft, tighten the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

SST
09922-10010  

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Turn
*b Hold


e.

Remove the pin from the No. 3 chain tensioner assembly.


Hide 13550 22.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY (for Bank 1)

a.
A222174E01
1.856,2.144 2.036,2.328 0.180,0.185 10 *1 1.146,2.882 1.319,3.067 0.173,0.185 10 *2 2.041,2.234 2.194,2.234 2.194,2.234 2.063,2.522 false 1.346,2.967 1.464,2.967 1.464,2.967 1.621,2.718 false 2.878,1.462 3.108,1.698 0.231,0.236 2.888,1.481 3.071,1.663 0.183,0.182 10 *a

Install the No. 2 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Push in the No. 2 chain tensioner assembly and insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the tensioner.

Text in Illustration
*1 Pin
*2 Plunger
*a Push


Hide 23.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

a.
A227958E01
1.605,0.015 1.795,0.216 0.190,0.201 10 *1 1.692,1.57 1.904,1.765 0.211,0.194 10 *2 2.615,0.412 2.398,0.11 2.398,0.11 1.855,0.11 false 0.67,0.935 1.036,0.109 1.036,0.109 1.561,0.109 false 0.837,0.841 1.805,1.544 1.805,1.544 2.642,0.941 false

Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.

Text in Illustration
*1 Timing Mark
*2 Mark Plate


b.

Apply a light coat of engine oil to the bolt threads and bolt-seating surface.


c.

Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.


d.
A221177E01
0.452,0.131 0.777,0.331 0.325,0.200 10 SST 2.74,0 2.961,0.198 0.221,0.198 10 *a 0.596,1.55 0.817,1.747 0.221,0.198 10 *b 0.845,0.215 0.983,0.215 0.983,0.215 1.297,0.632 false

Using SST to hold the hexagonal portion of each camshaft, tighten the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

SST
09922-10010  

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Turn
*b Hold


e.

Remove the pin from the No. 2 chain tensioner assembly.


Hide 13561 24.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
23 N*m (229 kgf*cm, 17 ft.*lbf)


Hide 13562 25.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.

Install the 2 No. 2 chain vibration dampers.


Hide 13521 26.INSTALL CRANKSHAFT TIMING SPROCKET

a.
U147416E04
1.417,0.292 1.594,0.49 0.177,0.198 10 false *a

Align the key groove of the timing sprocket with the timing sprocket set key.


b.

Install the timing sprocket to the crankshaft with the sprocket facing inward as shown in the illustration.

Text in Illustration
*a Inward


Hide 13581 27.INSTALL NO. 1 IDLE GEAR SHAFT

a.

Apply a light coat of engine oil to the sliding surface of the No. 1 idle gear shaft.


b.
A223643E01
0.211,0.352 0.374,0.535 0.163,0.184 10 *1 0.392,0.441 0.486,0.441 0.486,0.441 0.67,0.673 false

Temporarily install the No. 1 idle gear shaft and No. 1 idle gear with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block.

Text in Illustration
*1 Knock Pin

NOTICE:

Make sure that the idle gear is installed facing the proper direction.



c.

Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


d.

Remove the bar from the chain tensioner.


Hide 13506 28.INSTALL CHAIN SUB-ASSEMBLY

a.
A223644E04
0.927,0.875 1.156,0.427 1.156,0.427 1.229,0.427 false 2.708,0.771 2.938,0.333 2.938,0.333 3.01,0.333 false 1.156,1.479 1.063,1.479 1.063,1.479 0.833,1.021 false 2.271,1.49 2.438,1.49 2.438,1.49 2.635,0.948 false 1.229,0.333 1.427,0.521 0.198,0.188 10 true *1 2.052,1.396 2.25,1.583 0.198,0.188 10 true *2 1.167,1.396 1.365,1.583 0.198,0.188 10 false *2 3.021,0.26 3.219,0.448 0.198,0.188 10 true *1

Align the mark plate and timing marks as shown in the illustration and install the chain.

Text in Illustration
*1 Mark Plate
*2 Timing Mark

HINT:

The camshaft mark plates are orange.



b.
A221174

Do not pass the chain around the crankshaft, just temporarily place it on the crankshaft.


c.
A223645E04
0.177,2.885 3.344,4.542 3.167,1.656 2.396,4.01 2.854,4.01 false 1.646,3.885 0.917,3.885 false 1.625,3.979 1.323,4.333 1.323,4.333 2.208,4.083 false 0.229,2.875 0.458,3.083 0.229,0.208 10 false *a 0.719,3.781 0.885,3.99 0.167,0.208 10 false *b 1.094,4.25 1.281,4.427 0.188,0.177 10 false *c 2.875,3.917 3.104,4.125 0.229,0.208 10 false *1

Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain between the banks.

Text in Illustration
*1 Chain Plate
*a When idle sprocket is reused
*b Mark
*c Align
V100135

Turn

NOTICE:

When the idle sprocket assembly is reused, align the chain plate with the mark where the plate had been when tightening the chain between the banks.



d.
A223646E04
2.688,0.656 2.823,0.656 2.823,0.656 2.99,1.427 true 2.854,1.406 2.25,1.833 2.25,1.833 2.802,1.604 true 2.396,0.573 2.688,0.792 0.292,0.219 10 true *1 1.958,1.75 2.208,1.958 0.25,0.208 10 true *2

Align the mark plate and timing marks as shown in the illustration and install the chain to the crankshaft timing sprocket.

Text in Illustration
*1 Mark Plate
*2 Timing Mark

HINT:

The crankshaft mark plate is yellow.



e.

Temporarily install the pulley set bolt.


f.
A223647E04
0.677,0.25 0.615,0.25 0.615,0.25 0.5,0.375 false 0.615,0.583 0.385,1.427 0.385,1.427 1.479,0.948 false 2.219,1.979 2.042,1.979 2.042,1.979 1.813,1.76 false 0.677,0.167 0.948,0.417 0.271,0.25 10 true *1 0.188,1.417 0.375,1.604 0.188,0.188 10 false *2 2.24,1.885 2.427,2.063 0.188,0.177 10 false *3

Turn the crankshaft clockwise to set it to the RH block bore center line (TDC/compression).

Text in Illustration
*1 Center Line
*2 Timing Mark
*3 Sensor Plate


Hide 13559 29.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper.


Hide 13540 30.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A178214E01
0.272,1.579 0.456,1.790 0.184,0.211 10 *1 2.042,1.649 2.263,1.869 0.221,0.221 10 *a 0.484,1.662 0.676,1.662 0.676,1.662 0.918,1.074 false 2.826,1.599 3.009,1.810 0.184,0.211 10 *1 2.584,0.956 2.934,1.414 2.934,1.414 2.934,1.569 false

Turn the stopper plate of the tensioner clockwise and push in the plunger of the tensioner as shown in the illustration.

Text in Illustration
*1 Stopper Plate
*a Push


b.

Turn the stopper plate of the tensioner counterclockwise and insert a pin with a diameter of 1.27 mm (0.0500 in.) into the holes on the stopper plate and tensioner to fix the stopper plate in place.


c.

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the pin from the No. 1 chain tensioner.


Hide 31.INSPECT VALVE TIMING

a.

Check the camshaft timing marks.

NOTICE:
·

Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear.

·

If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.




b.

Check that each camshaft timing mark is positioned as shown in the illustration.

A223648E05
1.531,0.458 0.802,0.375 0.802,0.375 1.51,0.771 true 5.865,2.375 6.615,2.229 6.615,2.229 5.896,2.625 true 4.625,0.573 3.875,0.521 3.875,0.521 4.563,0.948 true 2.042,2.521 2.781,2.385 2.781,2.385 2.052,2.927 true 0.51,4.469 0.625,4.469 0.625,4.469 0.708,4.365 false 1.208,4.073 1.323,4.073 1.323,4.073 1.406,3.979 false 3.656,3.865 3.76,3.865 3.76,3.865 3.885,3.99 false 4.313,4.125 4.396,4.125 4.396,4.125 4.542,4.365 false 0.542,0.302 0.802,0.49 0.26,0.188 10 true *1 6.635,2.146 6.906,2.333 0.271,0.188 10 true *1 3.625,0.458 3.875,0.656 0.25,0.198 10 true *1 2.813,2.302 3.052,2.552 0.24,0.25 10 true *1 0.344,4.396 0.521,4.573 0.177,0.177 10 false *a 1.042,4.01 1.219,4.188 0.177,0.177 10 false *a 3.479,3.781 3.656,3.958 0.177,0.177 10 false *a 4.146,4.052 4.323,4.229 0.177,0.177 10 false *a

Text in Illustration
*1 Timing Mark - -
*a Viewpoint - -

HINT:
U113585E08
1.906,1.281 2.427,1.281 false 1.906,0.948 2.427,0.948 false 1.906,0.667 2.104,0.573 2.104,0.573 2.438,0.573 false 1.917,1.677 2.115,1.771 2.115,1.771 2.385,1.771 false 2.458,0.469 2.594,0.635 0.135,0.167 10 false A 2.458,0.854 2.594,1.021 0.135,0.167 10 false B 2.458,1.177 2.594,1.344 0.135,0.167 10 false C 2.469,1.667 2.604,1.833 0.135,0.167 10 false D

for Intake Camshaft:

Be sure to check mark A at the point when marks B, C and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.



c.

If the valve timing is misaligned, reinstall the timing chain.


d.

Remove the pulley set bolt.


Hide 16100 32.INSTALL ENGINE WATER PUMP ASSEMBLY

a.

Install a new gasket and the engine water pump with the 8 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 11302 33.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 12121 35.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.

Install the No. 1 oil pan baffle plate with the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15104 37.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 12102A 38.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 12101A 39.INSTALL OIL PAN DRAIN PLUG

a.

Install a new gasket and the drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 41.POUR ENGINE OIL

A224782

HINT:

Before installing the cylinder head cover, pour engine oil into the locations shown in the illustration.


Hide 11193 42.INSTALL SPARK PLUG TUBE GASKET

a.
A385866

Using a cutter knife, cut off the seal part of the removed gasket.

Text in Illustration
V100155

Area to cut off


b.
A226558E01
2.363,0.351 2.546,0.545 0.184,0.194 10 *1 0.79,1.225 0.968,1.404 0.178,0.178 10 *2 2.339,0.447 2.142,0.447 2.142,0.447 1.853,0.959 false 1.004,1.312 1.153,1.312 1.153,1.312 1.563,1.095 false

Using the removed gasket and a hammer, tap in a new gasket until it stops.

Text in Illustration
*1 Removed Gasket
*2 New Gasket

HINT:

If the removed gasket does not fit on the new one, correct the removed one with pliers.



c.

Apply a light coat of MP grease to the gasket lip.


d.

Return the ventilation baffle plate claws to their original positions.


Hide 11201 43.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover or cylinder head cover.


b.
A223667

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2 to 3 mm (0.0787 to 0.118 in.)


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A221164

Install 3 new gaskets as shown in the illustration.


d.

Install a new gasket to the cylinder head cover.


e.

Install the seal washers to the bolts.


f.
A221162E04
1.385,0.792 1.74,0.979 0.354,0.188 10 true 1, 11 1.344,2 1.469,2.146 0.125,0.146 10 true 3 0.135,0.292 0.313,0.448 0.177,0.156 10 true 4 1.083,0.146 1.26,0.333 0.177,0.188 10 true 5 1.885,0.083 2.073,0.271 0.188,0.188 10 true 6 3.135,0.146 3.292,0.333 0.156,0.188 10 true 7 3.198,1.021 3.323,1.208 0.125,0.188 10 false 8 3.115,1.698 3.24,1.885 0.125,0.188 10 false 9 1.979,2.01 2.188,2.156 0.208,0.146 10 false 10 0.448,1.979 0.656,2.125 0.208,0.146 10 true 12 0.146,1.229 0.354,1.375 0.208,0.146 10 false 13 2.385,0.031 2.573,0.219 0.188,0.188 10 true 2

Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.

Torque:
for bolt A and D : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B and C : 21 N*m (214 kgf*cm, 15 ft.*lbf)

Standard Bolt:
Item Length
A 25 mm (0.984 in.)
B 35 mm (1.38 in.)
C 65 mm (2.56 in.)
D 60 mm (2.36 in.)


Text in Illustration
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 11202 44.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover or cylinder head cover.


b.
A223664

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2 to 3 mm (0.0787 to 0.118 in.)


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A223665

Install 3 new gaskets as shown in the illustration.


d.

Install a new gasket to the cylinder head cover.


e.

Install the seal washers to the bolts.


f.
A221163E04
1.802,1.063 1.958,1.24 0.156,0.177 1.833,0.76 2.188,0.948 0.354,0.188 10 true 1, 10 0.906,0.052 1.031,0.24 0.125,0.188 10 true 2 3,1.802 3.125,1.948 0.125,0.146 10 false 3 2.094,1.958 2.219,2.146 0.125,0.188 10 false 4 0.042,1.271 0.167,1.458 0.125,0.188 10 false 5 0.135,0.135 0.26,0.323 0.125,0.188 10 true 6 1.573,0.115 1.698,0.302 0.125,0.188 10 true 7 3.25,0.302 3.375,0.49 0.125,0.188 10 true 9 0.021,1.604 0.229,1.75 0.208,0.146 10 false 12 1.354,1.979 1.563,2.125 0.208,0.146 10 true 13 0.229,1.979 0.635,2.146 0.406,0.167 10 true 11, 14 2.365,0.115 2.49,0.302 0.125,0.188 10 true 8

Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.

Torque:
for bolt A and D : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B and C : 21 N*m (214 kgf*cm, 15 ft.*lbf)

Standard Bolt:
Item Length
A 25 mm (0.984 in.)
B 35 mm (1.38 in.)
C 70 mm (2.76 in.)
D 60 mm (2.36 in.)


Text in Illustration
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 16356 48.INSTALL REAR WATER BY-PASS JOINT

a.
A076535E07
1.75,0.844 2.177,0.844 false 0.5,1.479 0.635,1.813 0.635,1.813 1.51,1.604 false 0.5,1.833 0.698,2.021 0.198,0.188 10 true *2 2.219,0.75 2.427,0.938 0.208,0.188 10 true *1

Apply soapy water to a new O-ring and install it to the water outlet pipe. Then install 2 new gaskets to the water ports LH and RH.

Text in Illustration
*1 New O-Ring
*2 New Gasket


b.

Install the rear water by-pass joint with the 2 bolts and 4 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12185 54.INSTALL OIL FILLER CAP HOUSING

a.
A221161E01
2.172,1.123 2.482,1.345 0.31,0.222 2.262,1.136 2.445,1.311 0.184,0.174 10 *1 1.98,1.464 2.104,1.224 2.104,1.224 2.226,1.224 false

Install a new gasket and the oil filler cap housing with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 New Gasket


b.

Install the oil filler cap.


Hide 15340 55.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2)

Hide 15330B 56.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 2)

Hide 15330B 57.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1)

Hide 15330B 58.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 1)

Hide 11301M 60.INSTALL VVT SENSOR (for Exhaust Side of Bank 2)

Hide 11301M 61.INSTALL VVT SENSOR (for Intake Side of Bank 2)

Hide 11301M 62.INSTALL VVT SENSOR (for Exhaust Side of Bank 1)

Hide 11301M 63.INSTALL VVT SENSOR (for Intake Side of Bank 1)

Hide 11415 64.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Apply adhesive to 2 or 3 threads of the cylinder block water drain cock end.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.
A273791E05
2.677,1.094 2.865,1.271 0.188,0.177 10 false *a 0.927,1.521 1.177,1.688 0.25,0.167 10 false 15° 1.135,1.74 1.385,1.906 0.25,0.167 10 false 15° 1.01,1.969 1.25,2.115 0.24,0.146 10 false 60°

Install the cylinder block water drain cock.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

Text in Illustration
*a Front

NOTICE:
·

Install the cylinder block water drain cock within 3 minutes after applying adhesive.

·

Do not expose the cylinder block water drain cock to coolant within 1 hour of the installation.




c.

Rotate the cylinder block water drain cock clockwise to the position shown in the illustration.

NOTICE:
·

Do not rotate the cylinder block water drain cock by more than 1 revolution (360°) after tightening the cylinder block water drain cock to the specified torque.

·

Do not loosen the cylinder block water drain cock after setting it correctly.




d.

Install the cylinder block water drain cock plug to the cylinder block water drain cock.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 83520 66.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY